Lutron Diva DVFSQ-F-AL 3-Speed Fan Control User Manual

Introducció

The Lutron Diva 3-Speed Fan Control (model DVFSQ-F-AL) provides convenient control over your ceiling fan's speed. This switch allows you to select from three quiet fan speeds and turn the fan on or off. It is designed for use in both single-pole and 3-way wiring configurations. A coordinating Claro wall plate is sold separately.

Informació de seguretat

ADVERTIMENT: To avoid fire, shock, or death, turn off power at the circuit breaker or fuse box and test that power is off before wiring. This device must be installed by a qualified electrician in accordance with all national and local electrical codes. Use only with permanently installed ceiling paddle fans. Do not use with fans that have proprietary remote controls, DC motor fans, or exhaust fans.

• Do not exceed the maximum electrical ratings: 1.5 Amps, 120 Volts AC, 60 Hz.
• Assegureu-vos una correcta connexió a terra.
• Do not use for controlling lighting loads.

Què s'inclou

El paquet inclou:

• One (1) Lutron Diva 3-Speed Fan Control (DVFSQ-F-AL)

Note: A coordinating Claro wall plate is sold separately and is not included with this unit.

Image: The Lutron Diva 3-Speed Fan Control in Almond, shown without a wall plate.

Compatibilitat

This fan control is designed for use with indoor ceiling paddle fans only. It is compatible with standard 3-speed ceiling fans that use a pull chain for speed control. It is no compatible amb:

• Ceiling fans with proprietary remote controls.
• DC motor fans.
• Exhaust fans.
• Lights or other electrical loads.

Image: A compatibility chart showing a checkmark for ceiling fans with pull chains and an 'X' for ceiling fans with pull chains and remotes.

Configuració i instal·lació

Abans de començar: Ensure power is turned off at the circuit breaker. This device requires a neutral wire for proper operation. If you are unsure about wiring, consult a qualified electrician.

Eines necessàries:

• Tornavís (Phillips i cap pla)
• Pelacables
• Cinta elèctrica
• Voltage provador

Instruccions de cablejat:

1. Apagueu l'alimentació: Locate the circuit breaker controlling the fan and turn it off. Verify power is off using a voltage provador.
2. Elimina l'interruptor existent: Traieu amb cura la placa de paret i descargoleu l'interruptor existent de la caixa de connexió. Desconnecteu els cables de l'interruptor antic.
3. Identificar els cables:
   • Hot (Line) Wire: Normalment negre, porta alimentació del disjuntor.
   • Cable de càrrega: Typically black, goes to the fan.
   • Fil neutre: Typically white, required for this switch.
   • Cable de terra: Normalment coure nu o verd.
   • Traveler Wires (for 3-way only): Two wires (often red and black) that connect between two 3-way switches.
4. Connecteu els cables:
   • Connecteu el Terra wire from the wall box to the green ground wire on the Lutron fan control.
   • Connecteu el Neutre wire from the wall box to the white neutral wire on the Lutron fan control.
   • Per Unipolar installation: Connect the Hot (Line) wire to one of the black wires on the fan control. Connect the Carrega wire (to the fan) to the other black wire on the fan control.
   • Per 3 vies installation: This control can be used with a standard 3-way switch. Connect the Hot (Line) wire to one of the black wires on the fan control. Connect the Carrega wire (to the fan) to the other black wire on the fan control. The traveler wires will connect to the corresponding terminals on the standard 3-way switch. Refer to the diagram provided with your standard 3-way switch for specific traveler connections.
5. Cablejat segur: Use wire nuts to secure all connections. Ensure no bare wire is exposed.
6. Interruptor de muntatge: Gently fold the wires into the wall box and secure the fan control with the provided screws.
7. Instal·leu la placa de paret: Attach the coordinating Claro wall plate (sold separately).
8. Restaura l'alimentació: Torneu a encendre l'alimentació al disjuntor.

Image: The Lutron Diva 3-Speed Fan Control installed in a wall, demonstrating its appearance with a wall plate.

Instruccions de funcionament

The Lutron Diva 3-Speed Fan Control features a large paddle switch and a linear slider for easy operation.

• Activació/desactivació: Press the large paddle switch to turn the ceiling fan on or off. The fan will resume at the last selected speed setting.
• Ajust de la velocitat del ventilador: Use the small linear slider located on the right side of the paddle switch to adjust the fan speed.
  • Slide the control up for higher fan speeds.
  • Slide the control down for lower fan speeds.
  • The control offers three distinct quiet fan speeds.

Image: A living space with a ceiling fan, illustrating the comfort provided by the 3 quiet fan speeds controlled by the Lutron Diva switch.

Image: The Lutron Diva fan control in a room setting, emphasizing its ability to eliminate the need for pull chains on ceiling fans.

Manteniment

The Lutron Diva 3-Speed Fan Control requires minimal maintenance.

• Neteja: To clean the surface of the control, wipe with a soft, damp cloth. Do not use chemical cleaners or abrasive materials, as these can damage the finish.
• Sense peces reparables per l'usuari: There are no user-serviceable parts inside the control. Do not attempt to disassemble or repair the unit.

Resolució de problemes

Especificacions

Garantia i Suport

Lutron provides comprehensive support for its products. For assistance with installation, operation, or troubleshooting, please contact Lutron customer support.

Lutron offers 24/7 customer support to help you with your project. You can reach them anytime for assistance.

For the most current warranty information, please refer to the documentation included with your product or visit the official Lutron weblloc.