Oxford Essential HotHands Heated Motorcycle Overgrips Instruction Manual

1. Producte acabatview

The Oxford Essential HotHands Heated Motorcycle Overgrips are designed to provide warmth to a rider's hands in cold weather conditions. These overgrips are compatible with standard 22mm (7/8") motorcycle handlebars. The system features a rainproof switch with an LED indicator and is engineered for low battery drain, typically drawing under 4 Amperes.

Figure 1: Oxford HotHands Essential Heated Over-Grips product packaging, illustrating key features and compatibility.

2. Contingut del paquet

Verifiqueu que tots els components siguin presents al paquet:

• 2 x HotHands Heated Overgrips
• 1 x Electronic Switch/Controller with LED indicator
• 1 x Fused Wiring Loom
• Cable Ties for securing wiring
• 1 x Instruction Booklet and Warranty Form

Figure 2: A pair of Oxford HotHands Heated Overgrips, ready for installation.

Figure 3: The electronic switch/controller unit for the Oxford HotHands system.

3. Instruccions d'instal·lació

Careful installation is crucial for optimal performance and safety. The overgrips are designed to fit over existing 22mm (7/8") handlebar grips.

1. Preparació del manillar: Ensure your motorcycle's handlebars are clean and free from debris. If installing on the throttle side, some existing throttle tube ridges may need to be sanded down for a smooth fit.
2. Dry Fit Overgrips: Before applying adhesive, dry-fit both heated overgrips onto the handlebars. Ensure they slide on smoothly and that the wiring exits in a position that does not interfere with controls (e.g., clutch lever) or restrict throttle movement. For the throttle side, verify that the throttle can achieve a full range of motion without binding or stretching the overgrip's wire. Mark the desired final position.
3. Aplicar adhesiu: Apply a small amount of the provided adhesive (or a suitable alternative, such as super glue) to the inside surface of the overgrip, particularly towards the inner end. The adhesive is typically runny and sets quickly, so work efficiently. Place a rag underneath to catch any drips.
4. Install Overgrips: Slide the overgrips onto the handlebars quickly and firmly to the marked position. Once in place, avoid making adjustments as the adhesive sets rapidly.
5. Controlador de muntatge: Select a suitable mounting location for the electronic switch/controller. The kit includes a metal mounting bracket, but flexibility exists for placement. Ensure the controller is accessible and visible during operation.
6. Cablejat de ruta: Connect the overgrip wires to the main wiring loom. Route all wiring carefully, ensuring it is clear of moving parts, pinch points, and heat sources. Use the provided cable ties to secure the wiring neatly along the handlebars and frame. Ensure sufficient slack in the throttle grip wiring to allow for full throttle rotation and handlebar movement without strain.
7. Connectar a la bateria: Connect the fused wiring loom directly to your motorcycle's battery terminals. The system is designed with an auto-shutoff feature to prevent battery drain if left on after the ignition is off.
8. Optional End Cap Modification: If using bar-end weights or mirrors, the rounded end caps of the overgrips can be carefully cut off. Do not cut further up the grip, as heating elements are embedded within the material.

Figure 4: Oxford HotHands Heated Overgrips shown installed on motorcycle handlebars, demonstrating typical placement.

Figure 5: Detailed wiring diagram illustrating connections for the Oxford HotHands system, including the controller, grips, fuse, and battery terminals.

4. Instruccions de funcionament

The Oxford Essential HotHands system features an intuitive control interface for adjusting heat levels.

1. Encès/apagat: Press the '+' button on the controller to power on the system. The LED indicator will illuminate. To power off, press the '-' button repeatedly until the lowest setting is reached, then press it once more.
2. Ajustar el nivell de calor: Use the '+' and '-' buttons to cycle through the available heat settings. The LED indicator will change to reflect the current heat level. The system typically offers multiple settings, allowing for precise temperature control.
3. Escalfament inicial: For rapid heating, it is recommended to start at a higher setting. Once the desired warmth is achieved, reduce the setting to maintain comfort.
4. Mode d'estalvi de bateria: The controller is equipped with a battery saver mode that automatically shuts off the grips if the motorcycle's voltage drops below a certain threshold, preventing excessive battery drain.

Figure 6: Diagram of the Intelligent Heat Controller, showing '+' and '-' buttons and LED indicators for heat levels.

5. Manteniment

The Oxford Essential HotHands Heated Overgrips require minimal maintenance.

• Neteja: Clean the overgrips and controller with a damp cloth. Avoid using harsh chemicals or abrasive cleaners that could damage the materials or electronic components.
• Inspecció del cablejat: Periodically inspect all wiring connections for signs of wear, corrosion, or damage. Ensure cable ties remain secure and that wires are not rubbing against any motorcycle components.
• Comprovació de fusibles: If the grips stop working, check the inline fuse in the wiring loom and replace it if necessary with a fuse of the same rating (5 Amperes).

6. Solució De Problemes

• Empunyadures que no s'escalfen:
  • Check all wiring connections for proper seating and continuity.
  • Inspect the inline fuse for breakage and replace if needed.
  • Ensure the battery connections are secure and free from corrosion.
  • Verifiqueu que la bateria de la motocicleta tingui prou càrrega.
• Una empunyadura no escalfa:
  • Inspect the wiring specific to the non-functional grip for kinks or damage, especially near the connector to the main loom. Straighten any kinks and secure the connection.
• Grips Not Turning Off:
  • Ensure the controller is functioning correctly. If the auto-shutoff feature is not engaging, verify the wiring to the battery is correct.

7. Especificacions

8. Garantia i Suport

The Oxford Essential HotHands Heated Overgrips typically include a warranty. Please refer to the instruction booklet and warranty form provided in your package for specific warranty terms, conditions, and contact information for customer support.