Geberit 115222111 200 F Actuator Plate User Manual

1. Introducció

This manual provides instructions for the installation, operation, and maintenance of the Geberit 115222111 200 F Actuator Plate. This product is designed for use with specific Geberit concealed cisterns to enable stop-and-go flushing functionality. Please read this manual thoroughly before installation and use to ensure proper function and longevity of the product.

2. Informació de seguretat

• Always ensure the water supply to the cistern is turned off before beginning any installation or maintenance work.
• Si no esteu segurs de cap pas, la instal·lació l'ha de dur a terme un professional qualificat.
• Use only genuine Geberit replacement parts if any components need to be replaced.
• Mantingueu les peces petites allunyades dels nens per evitar perills d'asfixia.
• Do not use abrasive cleaners or solvents on the actuator plate, as this may damage the finish.

3. Contingut del paquet

The Geberit 115222111 200 F Actuator Plate package includes:

• 1 x Geberit 200 F Actuator Plate
• Mounting frame (if applicable, refer to packaging)
• Actuator rods (if applicable, refer to packaging)
• Fastening material (screws, etc.)

Figura 1: Frontal view of the Geberit 200 F Actuator Plate. This image shows the multi-colour single flush plate with its two distinct buttons for stop-and-go flushing.

4. Configuració i instal·lació

The Geberit 200 F Actuator Plate is designed for front actuation and is compatible with the following Geberit concealed cisterns:

• Concealed cisterns: 110.700, 110.745, 110.800, 110.845
• Kombi fix: 110.755, 110.840, 110.850
• Duo fix: 111.100
• UP cisterns: UP320, UP300

4.1. Comprovacions prèvies a la instal·lació

• Ensure the concealed cistern is correctly installed and accessible.
• Verify that the mounting frame for the actuator plate is securely in place.
• Confirm that the water supply to the cistern is turned off.

4.2. Passos d'instal·lació

1. Prepare the Cistern: Open the inspection opening of the concealed cistern. Ensure all internal components are correctly positioned.
2. Insert Actuator Rods: Carefully insert the actuator rods into the designated holes on the flush mechanism. Ensure they are seated correctly and move freely.
3. Attach Mounting Frame: If not already installed, attach the mounting frame to the cistern according to the cistern's specific instructions. Secure it firmly.
4. Position Actuator Plate: Align the Geberit 200 F Actuator Plate with the mounting frame. The actuator rods should pass through the holes on the back of the plate.
5. Assegura la placa: Gently press the actuator plate onto the mounting frame until it clicks into place. Ensure it is flush with the wall and securely fastened. Some models may require tightening screws from the side or bottom.
6. Funcionalitat de prova: Turn the water supply back on. Press both flush buttons to ensure they actuate the flush mechanism correctly and return to their original position smoothly.

Figura 2: Pro lateralfile illustrating the depth dimension of the actuator plate, approximately 39mm (1.54 inches).

Figura 3: Frontal view illustrating the width and height dimensions of the actuator plate, approximately 340mm (13.39 inches) wide and 185mm (7.28 inches) high.

5. Instruccions de funcionament

The Geberit 200 F Actuator Plate features a stop-and-go flush function, allowing for water conservation.

• Initiate Flush: Press the larger flush button (typically the upper one) to start the water flow.
• Stop Flush: To stop the water flow prematurely and save water, press the same button again. The flush will cease immediately.
• Full Flush: For a full flush, press the larger button once and release. The flush will complete its cycle automatically.

6. Manteniment

6.1. Cleaning the Actuator Plate

• Clean the surface of the actuator plate regularly with a soft, damp tela.
• Use mild, non-abrasive cleaning agents. Avoid harsh chemicals, abrasive sponges, or solvents, as these can damage the finish.
• Dry the plate with a soft cloth after cleaning to prevent water spots.

6.2. Using Cleaning Tablets

The Geberit 200 F Actuator Plate is designed with a feed chute for cleaning tablets, compatible with UP cisterns UP320 and UP300.

1. Access the Chute: Gently pull the actuator plate forward from the top or side to access the cleaning tablet chute. Refer to your cistern's specific instructions for exact access.
2. Insereix la tauleta: Place a suitable toilet cleaning tablet into the designated chute. Ensure it drops into the cistern.
3. Re-secure Plate: Push the actuator plate back into its original position until it clicks securely.
4. Flux: Flush the toilet to dissolve the tablet and distribute the cleaning agent.

Note: Only use cleaning tablets specifically designed for in-cistern use and compatible with Geberit products. Avoid tablets that contain chlorine or other corrosive substances.

7. Solució De Problemes

If the problem persists after attempting these solutions, please contact Geberit customer support or a qualified plumber.

8. Especificacions

• Model: Geberit 200 F Actuator Plate (115222111)
• Aplicació: For stop-and-go flush, front actuation
• Compatible Cisterns: Geberit concealed cisterns 110.700, 110.745, 110.800, 110.845; Kombi fix 110.755, 110.840, 110.850; Duo fix 111.100; UP320, UP300
• Material: material d'art (plàstic)
• Color: Multi-colour (Alpine White)
• Product Dimensions (as listed): 0.39" de llargada x 7.48" d'amplada
• Actual Dimensions (approximate, based on diagrams):
  • Amplada: 340 mm (13.39 polzades)
  • Alçada: 185 mm (7.28 polzades)
  • Profunditat: 39 mm (1.54 polzades)
• Pes de l'article: 0.5 quilos
• Components inclosos: 1 x Geberit Actuator Plate 200 F

9. Garantia i Suport

For information regarding warranty coverage, please refer to the warranty card included with your product or visit the official Geberit website. For technical support, spare parts, or further assistance, please contact Geberit customer service through their official channels.

Geberit Oficial Weblloc: www.geberit.com