National Specialty Lighting XTL-1-HW/WH Xenon Under Cabinet Light Manual

Introducció

This manual provides detailed instructions for the installation, operation, and maintenance of your National Specialty Lighting XTL-1-HW/WH Xenon Under Cabinet Light. Please read all instructions carefully before beginning installation and retain this manual for future reference.

Instruccions importants de seguretat

• Llegeix totes les instruccions: Ensure you understand all steps before installation or operation.
• Ús només en interiors: This fixture is designed for dry, indoor locations. Do not install in wet or damp ambients.
• Desconnecteu l'alimentació: Always disconnect power at the circuit breaker before installing, servicing, or replacing bulbs.
• Electricista qualificat: La instal·lació l'ha de dur a terme un electricista qualificat o una persona familiaritzada amb el cablejat elèctric.
• Connexió a terra adequada: Assegureu-vos que l'aparell estigui correctament connectat a terra per evitar descàrregues elèctriques.
• Voltage: This fixture operates on 120V AC input, converting to 12V for the Xenon bulb.
• Tipus de bombeta: Use only the specified 18W T5 Wedge 12V Xenon bulb.

Contingut del paquet

Verifiqueu que tots els components siguin presents abans de començar la instal·lació:

• XTL-1-HW/WH Under Cabinet Light Fixture (1)
• 18W T5 Wedge 12V Xenon Bulb (1)
• Push-in Connectors (for wiring)
• Maquinari de muntatge (cargols)
• Manual d'instruccions (aquest document)

Configuració i instal·lació

Eines necessàries

• Tornavís (Phillips i/o de punta plana)
• Pelafils
• Drill (if pre-drilling pilot holes)
• Llapis
• Cinta mètrica

Muntatge de l'aparell

1. Apagueu l'alimentació: Locate the circuit breaker controlling the area where the light will be installed and turn off the power. Verify power is off using a voltage provador.
2. Determinar la ubicació: Choose a suitable location under a cabinet, ensuring adequate clearance and access for wiring. The fixture dimensions are 9" L x 4.63" W x 1.25" H.
3. Mark mounting points: Hold the fixture in the desired position and mark the mounting screw locations with a pencil.
4. Secure fixture: Using the provided mounting screws, attach the fixture securely to the underside of the cabinet.

Electrical Connection (Hardwire)

1. Preparació del cablejat: Route the 120V AC supply wires to the fixture's wiring compartment. Strip approximately 1/2 inch of insulation from the ends of the supply wires (black, white, ground).
2. Connecteu els cables: Use the provided push-in connectors to connect the fixture's wires to the supply wires:
   • Connecteu el negre (hot) wire from the supply to the negre wire of the fixture.
   • Connecteu el blanc (neutral) wire from the supply to the blanc wire of the fixture.
   • Connecteu el verd (ground) wire from the supply to the verd or bare copper wire of the fixture.
3. Connexions segures: Ensure all connections are tight and secure. Tuck wires neatly into the wiring compartment.
4. Install bulb: Gently insert the 18W T5 Wedge 12V Xenon bulb into the fixture's socket. Avoid touching the glass portion of the bulb with bare hands.
5. Close diffuser: Close the frosted glass diffuser lens. It features a simple hinged push-to-open mechanism.
6. Restaurar l'energia: Torneu a encendre l'alimentació al disjuntor.

Figura 1: Acabatview of the National Specialty Lighting XTL-1-HW/WH Xenon Under Cabinet Light, showing its compact design and key dimensions (Length: 9 inches, Width: 4.63 inches, Height: 1.25 inches). The image also highlights the frosted glass diffuser and the integrated hi-lo dimmer switch.

Funcionant la teva llum

The XTL-1-HW/WH fixture is equipped with an integrated hi-lo dimmer switch for adjustable light output.

• Per activar: Premeu l'interruptor a la posició 'ON'.
• Per ajustar la brillantor: The switch typically has a 'HI' and 'LO' setting. Select the desired brightness level.
• Per apagar: Press the switch to the 'OFF' position.

Manteniment

Substitució de bombetes

The Xenon bulb has an average life of 10,000 hours. When replacement is necessary:

1. Apagueu l'alimentació: Desconnecteu l'alimentació de l'aparell a l'interruptor automàtic.
2. Open diffuser: Gently push the hinged frosted glass diffuser to open it. No tools are required.
3. Treure la bombeta antiga: Carefully pull the old 18W T5 Wedge 12V Xenon bulb straight out of its socket.
4. Instal·lar una bombeta nova: Insert a new 18W T5 Wedge 12V Xenon bulb into the socket. Avoid touching the glass with bare hands; use a clean cloth or gloves if necessary.
5. Close diffuser: Close the frosted glass diffuser until it latches securely.
6. Restaurar l'energia: Torneu a encendre l'alimentació al disjuntor.

Neteja

To clean the fixture, ensure power is off. Wipe the exterior surfaces with a soft, dry cloth. For stubborn marks, a slightly damp cloth may be used, followed by drying. Do not use abrasive cleaners or solvents.

Resolució de problemes

Especificacions del producte

Garantia i assistència al client

For warranty information or technical assistance, please contact National Specialty Lighting customer support. Keep your purchase receipt as proof of purchase.

La informació de contacte normalment es pot trobar a la pàgina oficial del fabricant weblloc web o a l'embalatge del producte.