Loctite 5188 Gasket Sealant User Manual

Producte acabatview

The Loctite 5188 Gasket Sealant is an anaerobic flange sealant designed for rigid iron, aluminum, and steel flanged mating surfaces. It cures when confined in the absence of air between close-fitting metal surfaces. This product provides a flexible, solvent-resistant seal that will not tear or degrade. It is ideal for sealing close-fitting joints between rigid metal faces and flanges.

Figura 1: A red tube of Loctite 5188 Flange Sealant, 50ml size, with white cap and nozzle. The label clearly shows 'LOCTITE 5188 FLANGE SEALANT' and 'NET 1.69 FL. OZ. (50 ml)'.

Informació de seguretat

Always read the Material Safety Data Sheet (MSDS) prior to use. This product contains chemicals that may be harmful if misused. Keep out of reach of children. Use in a well-ventilated area.

• Eviteu el contacte amb la pell i els ulls. En cas de contacte, esbandiu immediatament amb aigua abundant i consulteu un metge.
• Do not ingest. If swallowed, do not induce vomiting; call a physician immediately.
• Utilitzeu equips de protecció personal (EPI) adequats, com ara guants i ulleres de seguretat.
• Emmagatzemar en un lloc fresc i sec, lluny de la llum solar directa i de les fonts de calor.

Setup and Surface Preparation

1. Superfícies netes: Ensure all mating surfaces are clean, dry, and free from oil, grease, and old gasket material. Use a suitable solvent cleaner if necessary.
2. Roughen Surfaces (Optional): For best adhesion, lightly abrade smooth surfaces with an abrasive pad or fine sandpaper, then clean again.
3. Comprova l'ajust: Verify that the parts to be sealed fit closely together. This product is designed for close-fitting metal surfaces.

Instruccions d'ús (aplicació)

1. Dispensar producte: Apply a continuous bead of Loctite 5188 to one of the flange faces. Ensure complete coverage around all bolt holes and mating surfaces.
2. Muntar peces: Assemble the components immediately after application. Light clamping is recommended to ensure intimate metal-to-metal contact.
3. Temps de curació:
   • Hora de fixació: The product will fixture (become tack-free) in approximately 20 minutes at room temperature (22°C / 72°F).
   • Curació completa: Full cure is typically achieved within 24 hours.
   • Nota: Cure speed can vary depending on the substrate material, bondline gap, and temperature. Active metals like brass or copper will cure faster, while passive substrates like stainless steel may require an activator (e.g., Loctite 7649) for faster cure.
4. Prova: Allow sufficient cure time before subjecting the assembly to operational pressures or temperatures.

Manteniment i emmagatzematge

• Emmagatzematge: Store the product in its original container in a cool, dry location. Optimal storage temperature is between 8°C and 21°C (46°F and 70°F).
• Vida útil: Refer to the product packaging for specific shelf life information.
• Neteja: Uncured product can be cleaned with organic solvents. Cured product must be removed mechanically (e.g., scraping).
• Eliminació: Dispose of product and packaging in accordance with local, regional, national, and international regulations.

Resolució de problemes

Especificacions

• Tipus de producte: Anaerobic Gasket Sealant
• Número de model: 1253203
• Volum: 50 mL (1.69 fl. oz.)
• Color: Vermell
• Interval de temperatura: -65 °F a 300 °F (-54 °C a 149 °C)
• Hora de fixació: Approximately 20 minutes (on steel)
• Temps de curació completa: 24 hores
• Flexibilitat: Altament flexible
• Fabricant: Loctite (Henkel)
• Country of Manufacturer: Estats Units

Informació de suport

For technical assistance, product inquiries, or safety data sheets, please visit the official Loctite weblloc o poseu-vos en contacte amb el seu servei d'atenció al client.

Loctite Official Weblloc: www.loctite.com

Botiga de la marca Amazon: Visit the Loctite Store on Amazon