Philips 24675-1 40W Fluorescent Lamp Manual d'instruccions

Informació important de seguretat

Read all instructions carefully before installing or using the Philips 24675-1 fluorescent lampSi no es segueixen aquestes instruccions, es poden produir descàrregues elèctriques, incendis o altres perills.

• ADVERTIMENT: Risc de descàrrega elèctrica. Desconnecteu l'alimentació abans de la instal·lació o el manteniment.
• Assegureu-vos que lamp is compatible with your fixture's ballast and voltagrequisits electrònics (50 volts).
• Do not use with dimmers unless specifically rated for fluorescent lamps and compatible with the ballast.
• Mànec lamps carefully. Avoid dropping or subjecting them to impact.
• Dispose of fluorescent lamps according to local regulations, as they contain mercury.
• Do not operate in wet locations or where directly exposed to water.

Configuració i instal·lació

This section provides instructions for safely installing your Philips 24675-1 fluorescent lamp.

Eines i materials necessaris:

• Philips 24675-1 Fluorescent Lamp
• Compatible fluorescent fixture
• Stepladder (if necessary)
• Guants de seguretat i protecció ocular

Passos d'instal·lació:

1. Step 1: Disconnect Power. Locate the circuit breaker or fuse box that controls the power to the light fixture. Turn off the power completely. Verifiqueu que l'alimentació està apagada utilitzant un voltagprovador electrònic si està disponible.
2. Step 2: Remove Old Lamp (si escau). Si es substitueix una l existentamp, carefully twist the old fluorescent tube 90 degrees and gently pull it out of the lampholders. Dispose of the old lamp correctament.
3. Step 3: Insert New Lamp. Align the pins on both ends of the Philips 24675-1 fluorescent lamp amb les ranures a la lampholders of your fixture. Gently push the lamp a la lampsuports fins que els passadors estiguin completament assentats.
4. Step 4: Rotate Lamp. Once seated, rotate the lamp 90 degrees until it locks securely into place. Ensure both ends are firmly connected and the lamp és estable.
5. Step 5: Restore Power. Un cop lamp is securely installed, restore power to the fixture from the circuit breaker or fuse box.
6. Step 6: Test Operation. Engegueu l'interruptor de la llum per confirmar la lamp il·lumina.

Figure 1: Philips 24675-1 40W Fluorescent Lamp. This image shows the tubular shape and standard pins of the fluorescent lamp, ready for installation into a compatible fixture.

Instruccions de funcionament

The Philips 24675-1 fluorescent lamp is designed for straightforward operation within a compatible fixture.

1. Encès/apagat: Use the wall switch or fixture switch to turn the lamp encès o apagat.
2. Temps d'escalfament: Fluorescent lamps may require a brief warm-up period (a few seconds) to reach full brightness, especially in colder environments.
3. Funcionament normal: El lamp will provide consistent illumination once fully warmed up.

Note: Frequent switching on and off can reduce the lifespan of fluorescent lamps. For optimal longevity, avoid rapid cycling.

Manteniment

Proper maintenance ensures optimal performance and extends the life of your Philips 24675-1 fluorescent lamp.

• Neteja: Ensure power is off before cleaning. Gently wipe the lamp amb un drap suau, sec i sense borrissol. No utilitzeu netejadors líquids ni materials abrasius.
• Inspecció: Inspeccioneu periòdicament la lamp and fixture for any signs of damage, loose connections, or discoloration. If any issues are found, disconnect power and consult a qualified electrician.
• Substitució: Substituïu la lamp when it reaches the end of its average rated life (2000 hours) or if it begins to flicker excessively, dims significantly, or fails to illuminate.
• Eliminació: Fluorescent lamps contain small amounts of mercury. Do not dispose of them in regular household trash. Consult your local waste management authority for proper recycling or disposal procedures.

Resolució de problemes

If you experience issues with your Philips 24675-1 fluorescent lamp, consulteu els problemes i solucions habituals següents:

Especificacions del producte

Detailed technical specifications for the Philips 24675-1 40W Fluorescent Lamp.

• Número de model: 24675-1
• Marca: Philips
• Tipus de llum: Fluorescent
• Wattage: 40 watts
• Voltage: 50 Volts
• Forma: Tubular (T)
• Brillantor: 140 lúmens
• Temperatura de color: 2700 Kelvin
• Índex de reproducció del color (CRI): 80
• Vida mitjana: 2000 hores
• Dimensions del producte: 1.75 x 1.75 x 24.5 polzades
• Pes de l'article: 6.4 unces
• Usos específics: Lamp

Garantia i Suport

For warranty information or technical support regarding your Philips 24675-1 fluorescent lamp, please refer to the official Philips weblloc web o contacteu directament amb el seu servei d'atenció al client.

Note: Warranty terms and conditions may vary by region and retailer. Keep your purchase receipt for warranty claims.