PerTronix Flame-Thrower Electronic Ignition Distributor User Manual

1. Introducció

This manual provides comprehensive instructions for the installation, operation, maintenance, and troubleshooting of your PerTronix Flame-Thrower Electronic Ignition Distributor (Model D134600). This distributor is designed to provide enhanced ignition performance for compatible Ford Small Block engines, featuring integrated Ignitor electronic ignition technology for improved reliability and power.

Si us plau, llegiu aquest manual detingudament abans de la instal·lació i l'ús per garantir el funcionament correcte i la seguretat.

2. Informació de seguretat

Observeu sempre les precaucions de seguretat següents:

• Desconnecteu la bateria del vehicle abans de realitzar qualsevol treball elèctric.
• Utilitzeu l'equip de protecció individual (EPI) adequat, incloent-hi ulleres i guants de seguretat.
• Ensure the engine is cool before working on ignition components.
• Keep ignition components away from flammable materials.
• Consult a qualified mechanic if you are unsure about any installation steps.
• Aquest producte conté productes químics coneguts per l'estat de Califòrnia per causar càncer i defectes de naixement o altres danys reproductius. Rentar-se les mans després de la manipulació.

3. Què hi ha a la caixa

Verifiqueu que tots els components siguin presents abans de començar la instal·lació:

• PerTronix Flame-Thrower Electronic Ignition Distributor (Model D134600)
• Distributor Cap
• Rotor
• Instruccions d'instal·lació (aquest manual)

Image: PerTronix Flame-Thrower Electronic Ignition Distributor with cap, rotor, and wiring visible.

4. Configuració i instal·lació

Una instal·lació correcta és crucial per a un rendiment òptim. Seguiu aquests passos amb atenció:

1. Preparació:
   • Desconnecteu el cable negatiu de la bateria.
   • Mark the position of the rotor on the old distributor relative to the distributor body, and the position of the distributor body relative to the engine block. This will help with re-timing.
   • Label all spark plug wires before removal.
2. Old Distributor Removal:
   • Remove the distributor cap and spark plug wires.
   • Disconnect any electrical connections to the old distributor.
   • Loosen the distributor hold-down clamp and carefully lift the old distributor out of the engine block. Note the rotation of the rotor as it comes out.
3. New Distributor Installation:
   • Ensure the engine is at Top Dead Center (TDC) on the compression stroke for cylinder #1.
   • Align the new PerTronix distributor's gear with the camshaft gear. The rotor should point to the #1 spark plug terminal on the cap when fully seated. You may need to slightly rotate the rotor or the oil pump drive shaft to engage the gears.
   • Once seated, ensure the distributor body is oriented correctly as marked during removal.
   • Secure the distributor with the hold-down clamp, but do not fully tighten yet to allow for timing adjustments.
4. Connexions de cablejat:
   • The PerTronix Ignitor module has two wires: a red wire and a black wire.
   • Connecteu el fil vermell to a switched 12-volt power source that is active when the ignition is in the "ON" and "START" positions. This must be a full 12V source, not a resisted wire.
   • Connecteu el filferro negre to the negative (-) terminal of the ignition coil.
   • Ensure all connections are clean and secure.
5. Final Assembly and Timing:
   • Install the new distributor cap and reattach the spark plug wires in the correct firing order.
   • Torneu a connectar el cable negatiu de la bateria.
   • Start the engine and use a timing light to set the ignition timing according to your vehicle's specifications.
   • Once timing is set, fully tighten the distributor hold-down clamp.

Imatge: Examples of Flame-Thrower distributors, illustrating the "Stock Look" and "Billet Plug n' Play" designs. The D134600 is a "Stock Look" model.

5. Instruccions de funcionament

The PerTronix Flame-Thrower Electronic Ignition Distributor operates automatically once installed and timed correctly. It replaces traditional points and condenser systems with a maintenance-free electronic module.

• The integrated Ignitor system delivers a consistent, high-energy spark to the spark plugs, improving combustion efficiency.
• The precision timing control ensures stable engine performance across all RPM ranges.
• No adjustments are required for the electronic ignition system itself after initial timing.

6. Manteniment

The PerTronix Flame-Thrower Electronic Ignition Distributor is designed for minimal maintenance. Unlike traditional points systems, there are no points to adjust or replace.

• Inspecció periòdica: Periodically inspect the distributor cap and rotor for cracks, carbon tracking, or excessive wear. Replace if necessary.
• Cablejat: Check all electrical connections for tightness and corrosion. Ensure wiring is routed away from hot or moving engine components.
• Neteja: Keep the exterior of the distributor clean and free from oil, grease, and dirt. Use a clean, dry cloth.
• Spark Plugs & Wires: For optimal performance, ensure your spark plugs and spark plug wires are in good condition and are compatible with electronic ignition systems.

7. Solució De Problemes

If you experience issues with your ignition system, consider the following common problems and solutions:

If problems persist after troubleshooting, contact PerTronix technical support.

8. Especificacions

9. Garantia i Suport

PerTronix products are manufactured to high standards and are backed by a limited warranty. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official PerTronix weblloc.

For technical support, installation assistance, or warranty claims, please contact PerTronix customer service:

• Weblloc: www.pertronix.com
• Telèfon: Consulteu el weblloc web per a números de contacte actuals.
• When contacting support, please have your product model number (D134600) and purchase information ready.