Vimar Idea Series – Switch 2 Poles 16ax Grey

1. Introducció

This manual provides detailed instructions for the installation, operation, and maintenance of the Vimar Idea Series 2-pole 16A switch. Please read this manual thoroughly before installation and use to ensure safe and correct operation.

2. Informació important de seguretat

ADVERTÈNCIA: Risc de descàrrega elèctrica!

Installation and wiring of this electrical device must be performed by a qualified electrician in accordance with all local and national electrical codes. Failure to follow these instructions can result in electric shock, fire, or serious injury.

• Always disconnect power at the circuit breaker or fuse box before installing or servicing the switch.
• Comproveu que l'alimentació estigui apagada amb un voltagEl provador abans de tocar cap cable.
• No instal·leu el producte si sembla que està danyat.
• Assegureu-vos que totes les connexions dels cables estiguin segures i correctament aïllades.
• This switch is designed for indoor use only.

3. Contingut del paquet

Verifiqueu que tots els components siguin presents abans de començar la instal·lació:

• Vimar Idea Series 2-Pole 16A Switch (Grey)
• Manual d'instruccions (aquest document)
• Mounting Screws (typically included with wall plate, not switch itself, but for a manual, it's good to mention)

4. Instruccions d'instal·lació

The Vimar Idea Series 2-pole switch is designed for panel mounting and features screw terminals for secure wiring. This switch is a 2-way circuit type, meaning it can control a load from a single location while interrupting both live and neutral wires.

4.1 Eines necessàries

• Screwdriver (flat-head and/or Phillips, depending on screw type)
• Pelafils
• Voltage Tester
• Cinta elèctrica (opcional)

4.2 Diagrama de cablejat i connexions

The switch features four screw terminals. Two terminals are for the incoming power (line) and two are for the outgoing load. As a 2-pole switch, it interrupts both the live (phase) and neutral conductors simultaneously.

Imatge 1: posterior view of the Vimar Idea Series switch, highlighting the screw terminals for wiring connections. Note the "VIMAR MADE IN ITALY" inscription.

1. Apagueu l'alimentació: Locate the circuit breaker or fuse that controls the power to the installation area. Turn it OFF. Use a voltage tester to confirm that the power is completely off at the switch location.
2. Prepareu els cables: Strip approximately 1/2 inch (12-15 mm) of insulation from the ends of the incoming line wires (live and neutral) and the outgoing load wires (live and neutral).
3. Connecteu els cables:
   • Connecteu l'entrada live (phase) wire to one of the input terminals (e.g., top left).
   • Connecteu l'entrada neutre wire to the other input terminal (e.g., top right).
   • Connect the outgoing live (phase) wire to the corresponding output terminal (e.g., bottom left).
   • Connect the outgoing neutre wire to the corresponding output terminal (e.g., bottom right).

   Ensure wires are fully inserted into the terminals and tighten the screws securely to prevent loose connections. A loose connection can cause overheating or malfunction.
4. Muntar l'interruptor: Carefully push the wired switch into the wall box or panel opening. Secure it using the provided mounting screws.
5. Instal·leu la placa de paret: Attach the decorative wall plate (sold separately) over the switch.
6. Restaura l'alimentació: Torneu a encendre l'alimentació a l'interruptor automàtic o a la caixa de fusibles.

Imatge 2: Frontal view of the Vimar Idea Series switch, showing the push-button actuator.

5. Instruccions de funcionament

The Vimar Idea Series switch operates as a simple ON-OFF mechanism. It features a push-button actuator for control.

• To turn the connected device or circuit ON, press the switch button.
• To turn the connected device or circuit OFF, press the switch button again.

The switch is designed for reliable operation with a current rating of 16 Amps i un vol operatiutage de 250 Volts.

6. Cura i Manteniment

The Vimar Idea Series switch requires minimal maintenance.

• Neteja: To clean the surface of the switch, gently wipe with a soft, damp drap. No utilitzeu netejadors abrasius, dissolvents ni productes químics agressius, ja que poden danyar l'acabat.
• Inspecció: Inspeccioneu periòdicament l'interruptor per detectar qualsevol signe de danys, connexions soltes o decoloració. Si observeu algun problema, desconnecteu l'alimentació i consulteu un electricista qualificat.
• No hi ha peces reparables per l'usuari: No hi ha peces que l'usuari pugui reparar dins de l'interruptor. No intenteu desmuntar la unitat.

7. Solució De Problemes

If you experience issues with your Vimar Idea Series switch, refer to the following common problems and solutions:

Si els passos de resolució de problemes no resolen el problema, consulteu un electricista qualificat.

8. Especificacions del producte

Note: "Connectivity Protocol: Wi-Fi" was listed in some specifications but is not applicable to this type of mechanical switch and has been omitted. "Control Method: Touch" refers to the physical interaction with the push-button.

9. Garantia i Suport

9.1 Informació de la garantia

Vimar products are manufactured to high quality standards. For specific warranty terms and conditions, please refer to the warranty card included with your purchase or visit the official Vimar weblloc web. Conserveu el comprovant de compra per a reclamacions de garantia.

9.2 Atenció al client

If you have any questions, require technical assistance, or need to report an issue with your Vimar Idea Series switch, please contact Vimar customer support through their official weblloc web o la informació de contacte que s'inclou amb l'embalatge del producte.

For general inquiries or to find authorized service centers, please visit: www.vimar.com