1. Introducció
This user manual provides comprehensive instructions for the installation, operation, maintenance, and troubleshooting of the Mean Well RSP-3000-48 AC-DC Power Supply. Please read this manual thoroughly before using the product to ensure safe and efficient operation. Keep this manual for future reference.
Image: The Mean Well RSP-3000-48 AC-DC Power Supply unit, shown with its detailed technical specifications table.
2. Característiques
- Entrada de CA: 180 - 264VAC
- Active Surge Current Limiting: Integrated for enhanced protection.
- Alta eficiència: Fins al 91.5%
- Funció PFC activa: Power Factor (PF) greater than 0.95.
- Proteccions: Includes Short Circuit, Overload, Over Voltage, Over Temperature, and Fan Alarm.
- Refrigeració: Forced air cooling via built-in DC fan with speed control function.
- Vol. De sortidatage Trim: Adjustable between 20-110% of the rated output voltage.
- High Power Density: Compact design for efficient power delivery.
- Compartició actual: Supports up to 3 units for increased power capacity.
- Alarm Signal Output: Provides relay contact and TTL signal for status monitoring.
- Sortida auxiliar: Built-in 12V/0.1A auxiliary output for remote control.
- Comandament a distància: Built-in remote ON-OFF control and remote sense function.
- Garantia: 5 years manufacturer's warranty.
3. Configuració i instal·lació
3.1 Precaucions de seguretat
- Ensure the power supply is disconnected from the AC mains before any installation or wiring.
- La instal·lació només l'ha de fer personal qualificat.
- Comproveu que l'entrada voltage range matches the power supply's specifications (180-264VAC).
- La connexió a terra adequada és essencial per evitar descàrregues elèctriques.
- No feu funcionar la unitat en ambients que superin els límits de temperatura i humitat especificats.
3.2 Muntatge
The RSP-3000-48 is designed for panel mounting. Ensure adequate ventilation space around the unit to allow for proper airflow and heat dissipation. Mount the unit on a metal plate of sufficient thickness (e.g., 360mm x 360mm x 1mm) to meet EMC directives and ensure proper thermal management.
3.3 Connexions de cablejat
- Entrada de CA: Connect the AC mains (Line, Neutral, Ground) to the designated input terminals. Use appropriate gauge wiring for the current rating.
- Sortida de corrent continu: Connect the load to the DC output terminals (+V, -V). Observe correct polarity.
- Detecció remota (opcional): If remote sense is used, connect the +S and -S terminals to the load's positive and negative terminals, respectively, to compensate for voltagcaiguda de e a través dels cables de sortida.
- Remote ON/OFF Control (Optional): Connect external control signals to the designated terminals for remote power management. Refer to the function manual for detailed wiring.
- Auxiliary Output (Optional): The 12V/0.1A auxiliary output can be used for remote control circuits.
- Current Sharing (Optional): For parallel operation, connect the current sharing terminals of multiple units as per the function manual.
4. Instruccions de funcionament
4.1 Engegada inicial
After completing all wiring connections and verifying safety precautions, apply AC power to the unit. The built-in fan will activate, and the output voltage should stabilize at the factory-set or previously adjusted level.
4.2 Vol. de sortidatage Ajust
El voltage can be trimmed between 20-110% of the rated output voltage (41-56V for 48V model) using an external control signal. Refer to the detailed function manual for specific instructions on how to implement this feature. Incorrect use of the Output Voltage TRIM function can damage internal components.
4.3 Seguiment
The unit provides an alarm signal output for monitoring operational status. Consult the function manual for details on interpreting these signals.
5. Manteniment
The Mean Well RSP-3000-48 power supply is designed for reliable operation with minimal maintenance. However, periodic checks are recommended:
- Neteja: Ensure the ventilation openings and fan blades are free from dust and debris to maintain optimal cooling performance. Disconnect power before cleaning.
- Inspecció del ventilador: Periodically check the cooling fan for proper operation. A malfunctioning fan can lead to overheating and reduced lifespan.
- Integritat de la connexió: Verify that all wiring connections are secure and free from corrosion.
- Condicions ambientals: Assegureu-vos que l'entorn de funcionament es mantingui dins dels rangs de temperatura i humitat especificats.
6. Solució De Problemes
If the power supply is not functioning correctly, perform the following basic checks:
- Sense Vol de sortidatage:
- Check if AC input power is present and correctly connected.
- Verify that the remote ON/OFF control is not activated (if used).
- Check for short circuits or overloads on the output. The unit has overload protection that may shut down the output.
- Sobreescalfament:
- Ensure adequate ventilation and that the cooling fan is operating.
- Check for excessive ambient temperature.
- Reduce the load if it exceeds the rated power.
- Vol. De sortidatage Fluctuació:
- Verify that the load is stable and not causing transient demands.
- Comproveu les connexions de teledetecció si s'han utilitzat.
- Alarm Signal Active:
- Consult the function manual to identify the specific alarm condition (e.g., fan alarm, over temperature).
If the problem persists after performing these checks, contact Mean Well technical support or your local distributor for assistance.
7. Specifications (RSP-3000-48)
The following table details the technical specifications for the Mean Well RSP-3000-48 AC-DC Power Supply:
| Categoria | Especificació | Value (RSP-3000-48) |
|---|---|---|
| Sortida | DC Voltage | 48 V |
| Corrent nominal | 62.5A | |
| Interval actual | 0-62.5A | |
| Potència nominal | 3000W | |
| Onda i soroll (màx.) | 200 mVp-p | |
| Voltage Adj. Interval | 41-56V | |
| Voltage Tolerància | ±1.0% | |
| Entrada | Voltage Rang | 180-264VCA, 254-370VDC |
| Interval de freqüència | 47-63 Hz | |
| Factor de potència (típ.) | PF>0.95/230VAC a plena càrrega | |
| Eficiència (Tipus) | 91.5% | |
| Corrent alterna (típ.) | 16 A/230 VCA | |
| Corrent d'entrada (típ.) | 60 A/230 VCA | |
| Protecció | Sobrecàrrega | 105-112% rated output power, constant current limiting with delay shutdown after 5 seconds, re-power on to recover |
| Més del voltage | 57.6-67.2V, shutdown, re-power on to recover | |
| Sobretemperatura | Shut down, re-power on to recover | |
| Funció | Auxiliary Power (AUX) | 12V@0.1A (Only for Remote ON/OFF control) |
| Control remot d'encesa/apagada | Please see the Function Manual | |
| Sortida de senyal d'alarma | Please see the Function Manual | |
| Vol. De sortidatage Trim | 8.6-56V (Note 3) | |
| Medi ambient | Temps de treball. | -20~+70°C (Refer to "Derating Curve") |
| Humitat de treball | ~ 20 90% d'humitat relativa sense condensació | |
| Temp. d'emmagatzematge, humitat | -40~+85°C, 10~95% HR sense condensació | |
| Temp. Coeficient | ±0.03%/°C (0~50°C) | |
| Vibració | 10~500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes | |
| Seguretat i EMC | Normes de seguretat | UL60950-1, TUV EN60950-1 approved |
| Resistir voltage | I/P-O/P:3KVAC, I/P-FG:2KVAC, O/P-FG:0.5KVAC | |
| Resistència d'aïllament | I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25°C / 70% RH | |
| Emissió EMC | Conformitat amb EN55022 (CISPR22) Classe B, EN61000-3-2,-3 | |
| Altres | MTBF | 184.9K hores min. MIL-HDBK-217F (25 °C) |
| Mida (L*W*H) | 278 x 177.8 x 63.5 mm | |
| Pes de l'article | 9.25 lliures |
Notes:
- All parameters not specifically mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature.
- Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair wire terminated with a 0.1uF & 47uF parallel capacitor.
- Tolerance includes set up tolerance, line regulation and load regulation.
- The power supply is considered a component which will be installed into a final equipment. All EMC tests have been executed by mounting the unit on a 360mm*360mm metal plate with 1mm of thickness. The final equipment must be re-confirmed to meet EMC directives. For guidance on how to perform these EMC tests, please refer to "EMI testing of component power supplies" (as available on www.meanwell.com).
- The PWM signal cannot be used to control the output voltage.
- If the "Output Voltage TRIM" function is not used, P/PFC and P/PWM of CN1 or CN2 must be shorted. If the "Output Voltage TRIM" function is used, P/PFC and P/PWM of CN1 or CN2 must be disconnected. Failure to follow these instructions may damage internal electrical components.
8. Garantia i Suport
8.1 Garantia
The Mean Well RSP-3000-48 AC-DC Power Supply comes with a Garantia del fabricant de 5 anys from the date of purchase. This warranty covers defects in materials and workmanship under normal use. It does not cover damage caused by improper installation, misuse, unauthorized modifications, or natural disasters.
8.2 Suport tècnic
For technical assistance, troubleshooting beyond the scope of this manual, or warranty claims, please contact your authorized Mean Well distributor or visit the official Mean Well weblloc web per a recursos de suport i informació de contacte.
