Schlage FE695 CAM 716 ACC Touch Camelot Lock with Accent Lever Instruction Manual

Introducció

The Schlage Touch Keyless Touchscreen Lever provides convenience and security for your home. This manual will guide you through the installation, operation, and maintenance of your electronic keyless entry lock.

Imatge: Frontal view of the Schlage FE695 CAM 716 ACC Touch Camelot Lock with Accent Lever in Aged Bronze finish, showing the keypad and lever.

Configuració i instal·lació

Before beginning installation, ensure you have the necessary tools: a tape measure, a #1 Phillips head screwdriver, and a #2 Phillips head screwdriver. If using a drive-in faceplate, you may also need a hammer, a block of wood, and a flat-head screwdriver. Do not use an electric drill as it can overtighten screws and damage the lock.

Door Measurement Verification

Verify your door dimensions to ensure proper fit:

• Diàmetre transversal: 2 1/8 polzades.
• Part posterior: Either 2 3/8 inches or 2 3/4 inches from the door edge to the center of the crossbore.
• Latch Bore: 1 inch in diameter.
• Gruix de la porta: Between 1 3/8 inches and 1 3/4 inches.

Image: Diagram showing the dimensions of the Schlage Touch Lock, including crossbore, backset, and thickness measurements.

Passos d'instal·lació

Follow these steps for installing your Schlage Touch lock. For a detailed visual guide, refer to the official installation video below.

1. Elimina el maquinari existent: Remove any existing lock hardware from your door.
2. Instal·leu el tancament: Insert the latch into the door edge, ensuring the bevel of the latch faces the door jamb and strike. Secure it with the provided shorter screws. If using a drive-in faceplate, remove the rectangular face and replace it with the round drive-in faceplate, then tap it into place flush with the door edge using a block of wood to protect it.
3. Determine Lever Orientation: Hold the exterior keypad up to the exterior of your door. Choose the lever that points away from the door jamb, with the tip pointed down.
4. Instal·lar palanques: Slide each lever onto its post and snap it into place.
5. Route Battery Cable: Route the battery cable over the latch and snap the exterior assembly into the crossbore. Snap-and-stay clips will help hold the touchscreen in place.
6. Position Interior Assembly: Route the battery cable through the wire routing slot on the rear of the inside assembly. Position the inside assembly on the door to align with the outside assembly.
7. Secure Assemblies: Connect the inside and outside assemblies with the two longer screws. Do not fully tighten yet.
8. Alinear i estrènyer: Check that the lock is straight, then fully tighten the mounting screws.
9. Connecta la bateria: Connect the exterior and interior battery cables. Attach the 9V battery and insert it into the holder. Carefully tuck the wires into the space surrounding the battery.
10. Substituïu la coberta de la bateria: Replace the battery cover on the inside assembly.

Instruccions de funcionament

Your Schlage Touch lock offers convenient keyless entry and customizable security features.

Entrada sense clau

• Pre-programmed Codes: Use the 2 pre-programmed codes for immediate use.
• Codis personalitzats: Assign up to 19 unique 4-digit user codes for trusted individuals.
• Introducció de codis: The downlighting illuminates numbers for easy entry in the dark. The fingerprint-resistant touchscreen helps protect the privacy of your access codes.

Modes de bloqueig

• Auto-locking Mode: The lock will automatically re-lock after a set period.
• Mode desbloquejat: The lock remains unlocked, allowing free entry and exit without a code.
• Interior Lever: The inside lever is always unlocked for easy exit, ensuring safety.

Image: The Schlage Touch Lock installed on a door, showcasinel seu disseny elegant i el seu teclat numèric.

Manteniment

Canvi de bateria

The lock operates with an included 9V battery. A dedicated low-battery indicator will alert you when the battery needs replacement. To replace the battery, remove the battery cover on the inside assembly, disconnect the old battery, connect the new 9V battery, carefully tuck the wires, and replace the cover.

Jumpstart Feature

In case of complete battery failure, a jumpstart feature is available. Locate the two pins on the very bottom just under the handle. Touch a 9V battery to these posts to temporarily provide power, allowing you to enter your code and gain access. This feature only provides power for code entry; it does not automatically unlock the door.

Resolució de problemes

If your lock does not perform properly after installation or during use, consult the troubleshooting section of your user guide. Common issues may include:

• Lock failing to latch.
• El teclat no respon.
• Difficulty entering codes.

Ensure all connections are secure and the battery has sufficient charge. For further assistance, refer to the support section.

Especificacions

• Marca: ESCHAGE
• Número de model: FE695CAM716ACC
• Tipus de bloqueig: Teclat
• Material: Plàstic
• Color: Bronze envellit
• Nom d'estil: Palanca d'accent
• Dimensions de l'article (L x A x A): 3 x 2.25 x 2.25 polzades
• Pes de l'article: 1.74 kg
• Font d'alimentació: Bateria de 9 V (inclosa)
• Security Rating: Grade 2/AAA
• Usos recomanats: Residential doors, home offices, wine cellars

Informació de la garantia

Schlage locks are backed by a limited lifetime mechanical and finish warranty, and a 3-year electronics warranty. Please refer to the official Schlage warranty documentation for full details and terms.

Image: Icon representing lifetime warranty.

Suport

For additional information, support, or to view more instructional videos, please visit:

• Weblloc: www.schlage.com
• Atenció al client: 888.805.9837