PROFLO PF5112HE Jerrit Toilet Tank Instruction Manual

1. Introducció

This manual provides detailed instructions for the installation, operation, and maintenance of your PROFLO PF5112HE Jerrit Toilet Tank. Please read all instructions carefully before beginning installation or use to ensure proper function and safety.

2. Informació de seguretat

• Tanqueu sempre el subministrament d'aigua del vàter abans de començar qualsevol instal·lació o manteniment.
• Durant la instal·lació, utilitzeu l'equip de protecció individual adequat, com ara guants i ulleres de protecció.
• Ceramic products can be heavy and fragile. Handle with care to prevent damage or injury.
• Ensure all connections are tightened securely to prevent leaks, but do not overtighten, which can crack ceramic or strip threads.
• Advertència de la proposta 65: Aquest producte us pot exposar a substàncies químiques, com ara el plom, que l'estat de Califòrnia sap que causa càncer i defectes de naixement o altres danys reproductius. Per a més informació aneu a www.P65Warnings.ca.gov.

3. Contingut del paquet

Your PROFLO PF5112HE Jerrit Toilet Tank package includes the following components:

• PROFLO PF5112HE Jerrit Toilet Tank (Vitreous China)
• Tapa del dipòsit
• Pre-installed fill valve and flush valve assembly
• Tank-to-bowl gasket
• Tank-to-bowl bolts, washers, and nuts
• Toilet base bolt caps

Note: A toilet bowl and toilet seat are not included with this tank and must be purchased separately.

4. Eines necessàries per a la instal·lació

• Clau ajustable
• Screwdriver (Phillips or flathead, depending on bolt type)
• Alicates
• Cinta mètrica
• Bucket and sponge (for cleanup)
• New water supply line (recommended)

5. Instruccions d'instal·lació

Follow these steps to install your PROFLO PF5112HE Jerrit Toilet Tank onto a compatible toilet bowl.

1. Preparar la tassa del vàter: Ensure the toilet bowl is clean and free of any old gaskets or debris. The bolt holes on the bowl should align with the tank's bolt spacing (approximately 5.5 inches center-to-center). The drain hole should be compatible with a 2-inch drain.
2. Install Tank-to-Bowl Gasket: Place the large rubber tank-to-bowl gasket over the flush valve opening on the bottom of the toilet tank. Ensure it is seated firmly and evenly.
3. Position the Tank: Carefully lift the toilet tank and align the bolt holes on the tank with the bolt holes on the toilet bowl. Gently lower the tank onto the bowl, ensuring the gasket creates a seal.
4. Assegureu el tanc: Insert the tank-to-bowl bolts through the tank and bowl holes. Place washers and nuts onto the bolts from underneath the bowl. Hand-tighten the nuts initially, then use an adjustable wrench to tighten them evenly, alternating between bolts. Do not overtighten, as this can crack the ceramic. The tank should be stable but not excessively rigid.
5. Connectar el subministrament d'aigua: Connect a new water supply line (recommended) from the shut-off valve to the fill valve on the bottom of the tank. Hand-tighten, then use a wrench for a final quarter-turn.
6. Restaurar el subministrament d'aigua: Slowly turn on the water supply valve. Check for any leaks around the tank-to-bowl connection and the water supply line. Tighten connections slightly if leaks are observed.
7. Comprovar el nivell d'aigua: Allow the tank to fill. The water level should stop below the overflow tube. Adjust the fill valve if necessary to achieve the correct water level.
8. Install Tank Lid: Place the tank lid securely on top of the tank.

6. Instruccions de funcionament

The PROFLO PF5112HE Jerrit Toilet Tank is designed for efficient flushing with a 1.28 gallons-per-flush (GPF) rate.

• To flush, press down firmly on the flush lever located on the side of the tank.
• For a thorough flush, hold the lever down until the tank is completely empty.
• Allow the tank to refill completely before flushing again.

7. Manteniment

• Neteja: Clean the exterior of the tank with a soft cloth and mild, non-abrasive cleaner. Avoid harsh chemicals that can damage the ceramic finish.
• Components interns: Periodically inspect the fill valve, flush valve, and flapper for wear or damage. Replace components as needed to maintain optimal performance and prevent leaks.
• Detecció de fuites: Regularly check for visible leaks around the base of the tank, the water supply line, and inside the tank. Address any leaks promptly to prevent water damage.

8. Solució De Problemes

• Problema: El vàter funciona contínuament o s'encén i s'apaga cíclicament.
  Solució: Check the fill valve for proper adjustment. Ensure the water level is not too high, causing water to flow into the overflow tube. Inspect the flapper for a proper seal; replace if worn or damaged.
• Problema: Esbandida feble o incompleta.
  Solució: Ensure the water level in the tank is at the maximum recommended level. Adjust the fill valve if the water level is too low. Check that the flapper opens fully and stays open long enough for the tank to empty.
• Problema: Leaks around the base of the tank.
  Solució: Turn off the water supply. Gently tighten the tank-to-bowl bolts evenly. If the leak persists, the tank-to-bowl gasket may need to be replaced.
• Problema: Slow tank refill.
  Solució: Check the water supply valve to ensure it is fully open. Inspect the fill valve for any obstructions or debris that might be restricting water flow.

9. Especificacions

10. Garantia i Suport

For detailed warranty information and customer support, please refer to the official PROFLO website or the documentation included with your product. You may also contact PROFLO customer service directly for assistance with product inquiries, parts, or troubleshooting not covered in this manual.