Movo MV-B100 Motorized Sensor Cleaning Brush User Manual

1. Producte acabatview

The Movo MV-B100 Motorized Sensor Cleaning Brush is designed for the safe and effective removal of dust and loose particles from DSLR and mirrorless camera sensors, lenses, and other sensitive optical surfaces. This device utilizes a motorized brush that generates a static charge to attract and lift dust, complemented by integrated LED lights to illuminate the cleaning area.

Image 1.1: The Movo MV-B100 Motorized Sensor Cleaning Brush with its protective cap on.

Característiques principals:

• Motorized Static Charge: An ultrasonic motor spins the brush fibers to create a static charge, enhancing dust attraction.
• Safe for Sensors: Ultrasoft brush fibers are safe for all camera sensors (mirrored and mirrorless) and glass optics.
• Llums LED integrades: Four super-bright LEDs illuminate the sensor surface, making dust particles visible.
• Funció d'auto-neteja: The brush cleans itself after use by spinning off collected dust.
• Funciona amb piles: Requereix 2 piles AAA (no incloses).

2. Configuració i instal·lació de la bateria

Before using your Movo MV-B100, you will need to install two AAA batteries.

1. Traieu la tapa protectora: Gently pull off the clear protective cap from the brush head.
2. Accés al compartiment de la bateria: Locate the battery compartment cover on the handle of the device. Slide the cover open to reveal the battery slots.
3. Insereix les piles: Introduïu dues piles AAA, assegurant-vos de la polaritat correcta (+/-) tal com s'indica a l'interior del compartiment.
4. Compartiment tancat: Torneu a col·locar la tapa del compartiment de la bateria fins que sentiu un clic i quedi ben fixada al seu lloc.
5. Substituïu la tapa protectora: Place the protective cap back over the brush head when not in use to keep the bristles clean.

Image 2.1: The Movo MV-B100 with its protective cap removed, revealing the brush head. The battery compartment is located on the handle.

3. Instruccions de funcionament

Follow these steps for effective and safe cleaning of your camera sensor or lens:

1. Prepara la teva càmera: Ensure your camera's battery is fully charged. Access your camera's sensor cleaning mode (if available) or set it to Bulb mode with the shutter locked open to expose the sensor. Consult your camera's manual for specific instructions on accessing the sensor.
2. Inspect the Sensor/Lens: Use the Movo MV-B100's integrated LED lights to inspect the surface for dust. Slide the power switch to the first position to activate the motor and charge the brush. Then, slide it to the second position to turn on the LEDs and stop the brush from spinning. The bright lights will highlight dust particles.
3. Charge the Brush: Before cleaning, ensure the brush is charged. Slide the power switch to the first position (motor on) for 3-5 seconds to allow the brush fibers to static charge.
4. Netegeu la superfície: With the brush charged (and motor off, LEDs on), gently sweep the brush across the sensor or lens surface. Avoid applying pressure. The static charge will attract and lift dust particles. For camera sensors, make light, overlapping passes.


Image 3.1: Gently sweeping the Movo MV-B100 brush across a camera sensor to remove dust.

5. Self-Clean the Brush: After cleaning, slide the power switch back to the first position (motor on) to allow the brush to spin and shed collected dust. This prepares the brush for its next use.
6. Re-inspect: Use the LED lights again to check if all dust has been removed. Repeat the cleaning process if necessary.

Image 3.2: The brush can also be used to clean dust from the surrounding areas of the camera mount.
7. Apagar i emmagatzemar: Once cleaning is complete, slide the power switch to the "off" position and replace the protective cap.

Nota important: The Movo MV-B100 is designed for dry dust removal. It is not intended to remove oil, smudges, or stubborn, stuck-on particles. For such contaminants, specialized wet cleaning solutions and swabs may be required. Always ensure the sensor is free of oil or wet residue before using the brush to prevent spreading contaminants.

4. Manteniment i cura

• Brush Self-Cleaning: After each use, activate the motor (first switch position) for a few seconds to allow the brush to spin and shed any collected dust, keeping the fibers clean for the next use.
• Deep Cleaning the Brush: If the brush fibers become visibly dirty or less effective, they can be gently washed with mild soap and water. Ensure the brush head is completely dry before reattaching it to the motorized unit and before subsequent use.
• Emmagatzematge: Always store the Movo MV-B100 with its protective cap on to prevent dust accumulation on the brush fibers. Store in a clean, dry environment.
• Substitució de la bateria: Replace AAA batteries when the motor speed decreases or the LED lights dim.

5. Solució De Problemes

6. Especificacions del producte

7. Garantia i Suport

Informació de la garantia:

The Movo MV-B100 Motorized Sensor Cleaning Brush comes with a Garantia limitada de 1 anys from the date of purchase. This warranty covers manufacturing defects and workmanship under normal use. It does not cover damage caused by misuse, accident, unauthorized modification, or improper battery installation.

Conserveu el vostre comprovant de compra per a reclamacions de garantia.

Atenció al client:

For technical assistance, warranty claims, or any questions regarding your Movo MV-B100, please contact Movo's friendly US-based customer support team. You can typically find contact information on the official Movo weblloc web o a través dels canals d'assistència del vostre distribuïdor.

Weblloc: www.movophoto.com (Exampl'enllaç, l'enllaç real pot variar)

We are committed to providing reliable products and helpful support.