Manual d'usuari del relé d'impulsos electromecànic Finder Sèrie 27 Tipus 270182300000

1. Introducció

This manual provides essential information for the safe and efficient installation, operation, and maintenance of the Finder Series 27 Type 270182300000 Electromechanical Pulse Relay. Please read this manual thoroughly before using the product and retain it for future reference.

The Finder Series 27 pulse relay is a 10 A, unipolar switch with 1 normally open (NO) contact, designed for AC 50/60 Hz systems at 230 V. It features a standard design with socket clamps for connection and is suitable for panel mounting.

2. Informació de seguretat

ADVERTIMENT: Electrical shock hazard. Installation and maintenance should only be performed by qualified personnel in accordance with all local and national electrical codes.

• Always disconnect power before installing, servicing, or removing the relay.
• Assegureu-vos de posar a terra correctament per evitar descàrregues elèctriques.
• Comproveu que el volum de subministramenttage and current ratings match the relay's specifications.
• Do not operate the relay in environments exceeding its specified temperature or humidity limits.
• Avoid exposing the relay to moisture or corrosive substances.

3. Producte acabatview

The Finder Series 27 Electromechanical Pulse Relay is designed for applications requiring sequential switching, such as lighting control. Key features include:

• Muntatge al panell: Designed for secure installation within electrical panels.
• AC Coils: Operates with alternating current.
• 1 NO Contact: Features one normally open contact for switching circuits.
• 3 Sequences Available: Supports various operational sequences.
• Alta capacitat de potència: Valorat per 10 Amps and 2400 Watts at 230 Volts.

Figura 3.1: Davant view of the Finder Series 27 Electromechanical Pulse Relay, showing its transparent casing and terminal connections.

4. Configuració i instal·lació

This pulse relay is designed for panel mounting. Follow these steps for proper installation:

1. Desconnexió d'alimentació: Ensure all power to the installation area is disconnected at the main circuit breaker before beginning any work.
2. Muntatge: Securely mount the relay within an electrical panel using appropriate fasteners. The relay dimensions are approximately 1.26 x 2.17 x 2.76 inches.
3. Connexions de cablejat:
   • Identify the three terminals on the relay.
   • Connect the control circuit wires to the coil terminals (A1, A2) as indicated on the relay. The coil voltage is 230 Volts AC.
   • Connect the load circuit wires to the contact terminals (1 NO) using the clamp-type connectors. The relay is rated for 10 Amps.
   • Assegureu-vos que totes les connexions estiguin ben ajustades i segures per evitar contactes solts i sobreescalfament.
4. Verificació: Double-check all wiring against the electrical diagram for your specific application.
5. Restauració d'energia: Un cop finalitzada i verificada la instal·lació, restableix l'alimentació del circuit.

Figura 4.1: Detallada view of the Finder Series 27 Relay's screw terminals, illustrating connection points for wiring.

5. Instruccions de funcionament

The Finder Series 27 pulse relay operates automatically based on the control signals it receives. It is commonly used in applications where a momentary input signal triggers a change in the output state, which then remains until the next momentary input.

• When a pulse is applied to the coil terminals (A1, A2), the internal mechanism latches, changing the state of the 1 NO contact.
• The contact remains in this new state even after the control pulse is removed.
• A subsequent pulse will revert the contact to its original state.
• The relay supports three distinct operational sequences, which are determined by the specific model variant and internal configuration. Refer to your system's wiring diagram for the exact sequence implemented.

Figura 5.1: Example of the Finder Series 27 Relay integrated into a kitchen lighting system, demonstrating its application in controlling light fixtures.

Figura 5.2: The Finder Series 27 Relay shown in a living room setting, illustrating its use for managing multiple light sources.

6. Manteniment

The Finder Series 27 pulse relay is designed for long-term, reliable operation with minimal maintenance. However, periodic inspection is recommended:

• Inspecció visual: Inspeccioneu periòdicament el relé per detectar qualsevol signe de danys físics, decoloració o connexions soltes.
• Neteja: Si cal, netegeu suaument l'exterior del relé amb un drap sec i suau. No utilitzeu dissolvents ni netejadors abrasius.
• Comprovació de la connexió: Assegureu-vos que totes les connexions del cablejat estiguin ben ajustades i segures.
• Condicions ambientals: Verifiqueu que l'entorn operatiu es mantingui dins dels rangs de temperatura i humitat especificats.

Nota: The relay is a sealed unit and is not user-serviceable internally. Do not attempt to open the casing.

7. Solució De Problemes

If the Finder Series 27 pulse relay is not functioning as expected, consider the following troubleshooting steps:

• No Response to Control Signal:
  • Check if power is supplied to the control circuit and the relay coil (A1, A2).
  • Verify that the control signal voltage coincideix amb el volum de la bobina del relétage (230 V AC).
  • Inspect control circuit wiring for breaks or loose connections.
• Càrrega no commutadora:
  • Ensure the relay is receiving control pulses and its internal mechanism is audibly clicking or visibly changing state (if applicable).
  • Check the load circuit wiring for continuity and secure connections.
  • Verifiqueu que el corrent de càrrega no superi els 10 del relé. Amp qualificació.
  • Confirm that the load itself is functional.
• Relay Overheating:
  • Ensure the load current does not exceed the relay's maximum rating.
  • Check for proper ventilation around the relay within the panel.
  • Verify that the ambient temperature is within the specified operating range.

If issues persist after performing these checks, contact a qualified electrician or Finder technical support.

8. Especificacions

9. Garantia i Suport

For information regarding warranty coverage, technical support, or service, please contact Finder directly through their official weblloc web o distribuïdors autoritzats. Conserveu el rebut de compra com a comprovant de compra.

Fabricant: TROBADOR

Número de peça: 27.01.8.230.0000