Introducció
This manual provides detailed instructions for the installation, operation, and maintenance of the DIGITEN G1 Water Flow Sensor, Model FL-808. This Hall effect flow sensor is designed for accurate measurement of liquid flow within a range of 1 to 60 liters per minute. Please read this manual thoroughly before use to ensure proper function and safety.
Producte acabatview
The DIGITEN G1 Water Flow Sensor (Model FL-808) is a robust and reliable device for measuring water flow. It features G1 (0.5 inch) threaded connections for easy integration into various systems. The sensor outputs a square wave pulse signal proportional to the flow rate, making it suitable for microcontrollers and other electronic systems.
Característiques principals:
- Construcció duradora: Waterproof, heat-resistant, pressure-resistant, and cold-resistant design.
- Ampli rang de flux: Measures flow from 1 to 60 Liters per minute.
- Fàcil instal·lació: Simple G1 (0.5 inch) threaded connections.
- Sortida de pols: Generates a square wave pulse signal for flow rate calculation.
- Conforme a RoHS: Compleix amb els estàndards mediambientals.
Informació de seguretat
- Assegureu-vos que la font d'alimentació estigui desconnectada abans de la instal·lació o el manteniment.
- Do not exceed the maximum operating pressure of 1.75 MPa.
- Verify correct wiring connections to prevent damage to the sensor or connected equipment.
- Avoid installing the sensor in locations with extreme vibrations or corrosive environments.
- This device is intended for water flow measurement. Do not use with other liquids without verifying compatibility.
Contingut del paquet
- 1 x DIGITEN G1 Water Flow Sensor (Model FL-808)
Especificacions tècniques
| Model | FL-808 |
| Material | Metal (Internal components), Plastic (Housing) |
| Mida de la connexió d'entrada/sortida | G1 (0.5 inch) Threaded |
| Interval de cabal | 1 - 60 l/min |
| Pressió màxima de funcionament | 1.75 MPa (17.5 bar) |
| Vol. Operatiutage Rang | DC 5 - 24 V |
| Corrent de funcionament | Cannot exceed 10 mA (at DC 5V) |
| Senyal de sortida | Square Wave Pulse |
| Frequency Formula | F = 4.8 * Q (L/min) ± 2% |
| Output Pulse per Liter | Approximately 450 pulses/liter |
| Temperatura de funcionament | ≤ 80°C |
| Humitat de funcionament | 35% - 90% HR |
| Temperatura d'emmagatzematge | -25 °C a +80 °C |
| Humitat d'emmagatzematge | 25% - 95% HR |
| Resistència d'aïllament | > 100 MΩ |
| Longitud del cable | 15 cm |
| Pes del producte | 80 grams |
Configuració i instal·lació
1. Instal·lació mecànica
The flow sensor features G1 (0.5 inch) male threaded connections on both ends. Ensure the flow direction arrow on the sensor body aligns with the intended water flow in your system. Apply appropriate thread sealant (e.g., PTFE tape) to prevent leaks. Tighten connections securely but do not overtighten.
Figura 1: Frontal view of the DIGITEN G1 Water Flow Sensor, showing the G1 threaded connections and the product label.
Figure 2: Technical drawing illustrating the dimensions and internal structure of the DIGITEN G1 Water Flow Sensor.
2. Cablejat elèctric
The sensor has a 3-wire connection. Connect the wires as follows:
- Fil vermell: VCC (+) - Connect to DC 5V to 24V power supply.
- Fil negre: GND (-) - Connect to ground.
- Fil groc: Signal Output - Connect to your microcontroller or data acquisition system's input pin.
Assegureu-vos que el vol operatiutage is within the specified range of DC 5-24V. The current drawn by the sensor should not exceed 10mA at 5V DC.
Figura 3: Primer pla view of the sensor's wiring connections: Red (VCC), Black (GND), and Yellow (Signal).
Figura 4: Detallada view of the 3-pin connector attached to the sensor's cable.
Instruccions de funcionament
Principi de funcionament
The DIGITEN G1 Water Flow Sensor uses a Hall effect sensor to detect the rotation of an internal turbine. As water flows through the sensor, it spins a turbine, and a magnet attached to the turbine generates a series of electrical pulses. The frequency of these pulses is directly proportional to the flow rate of the water.
Flow Rate Calculation
The output signal is a square wave. The flow rate (Q in L/min) can be calculated from the measured frequency (F in Hz) using the following formula:
F = 4.8 * Q (L/min)
Therefore, to find the flow rate:
Q (L/min) = F / 4.8
The sensor provides approximately 450 pulses per liter of water. The accuracy is ±2%.
Figura 5: Intern view of the sensor, highlighting the turbine mechanism responsible for pulse generation.
Figure 6: The sensor with its label clearly visible, detailing model number, working range, and wiring information.
Manteniment
- Inspecció periòdica: Periodically check for any signs of leaks at the connections or damage to the sensor body and wiring.
- Neteja: If the sensor's accuracy degrades, it may be due to debris accumulation inside the turbine. Disconnect power and water supply, then carefully remove the sensor for inspection and cleaning. Use a soft brush and clean water to remove any obstructions.
- Emmagatzematge: If storing the sensor for an extended period, ensure it is clean, dry, and kept within the specified storage temperature and humidity ranges (-25°C to +80°C, 25%-95% RH).
Resolució de problemes
| Problema | Causa possible | Solució |
|---|---|---|
| Sense sortida de senyal |
|
|
| Inaccurate flow readings |
|
|
| Fuites a les connexions |
|
|
Garantia i Suport
For warranty information or technical support, please contact DIGITEN customer service through the retailer where the product was purchased or visit the official DIGITEN website. Please have your product model number (FL-808) and purchase details ready when contacting support.