WINGONEER TB6560
WINGONEER TB6560 3A Single-Axis Stepper Motor Driver Board User Manual
Introducció
This manual provides detailed instructions for the installation, operation, and maintenance of the WINGONEER TB6560 3A Single-Axis Stepper Motor Driver Board. Please read this manual thoroughly before using the product to ensure proper function and safety.
Informació de seguretat
- Ensure power is disconnected before making any wiring connections or adjustments.
- Operate the board within the specified voltage i límits de corrent per evitar danys.
- Avoid touching components while the board is powered, especially the heatsink, as it may become hot.
- This device is intended for use by individuals familiar with electronics and stepper motor control.
Producte acabatview
The WINGONEER TB6560 3A Single-Axis Stepper Motor Driver Board is designed for controlling a single stepper motor. It features adjustable current settings and microstepping capabilities, making it suitable for various applications requiring precise motor control.
Figure 1: Top angled view of the TB6560 driver board, highlighting the terminal blocks for motor and power connections, as well as the DIP switches for configuration.
Figura 2: Angle view of the TB6560 board, showing the heatsink attached to the TB6560 chip, which is crucial for heat dissipation during operation.
Figura 3: A baix view of the TB6560 driver board, illustrating the printed circuit board (PCB) layout and the underside of the heatsink.
Especificacions
| Característica | Valor |
|---|---|
| Marca | WINGONEER |
| Voltage | 10 Volts, 24 Volts (Operating Range) |
| Material | Plastic (Board components) |
| Pes de l'article | 73 grams (2.57 unces) |
| Fabricant | WINGONEER |
| UPC | 723466639095 |
| Dimensions del paquet | 4.72 x 4.09 x 0.94 polzades |
Configuració i instal·lació
1. Connexions de cablejat
Before connecting any wires, ensure the power supply is disconnected. Refer to the board's labels for correct polarity and pin assignments.
- Font d'alimentació: Connect a DC power supply (10V-24V) to the designated power input terminals. Observe polarity: V+ for positive, V- for negative.
- Motor pas a pas: Connect your 4-wire or 6-wire stepper motor to the motor output terminals (A+, A-, B+, B-). For 6-wire motors, the center taps are typically left unconnected or connected as per specific motor requirements.
- Control Signals: Connect your control signals (STEP, DIR, ENA) from your microcontroller or CNC controller to the corresponding input pins on the driver board. Ensure a common ground connection.
2. Configuració del commutador DIP
The TB6560 board features DIP switches to configure the output current and microstepping resolution. Always adjust DIP switches when the board is unpowered.
Configuració actual
The output current can be set using a combination of DIP switches. Refer to the silkscreen on the board or the following table for common settings. The maximum current is 3A.
| Interruptor DIP 1 | Interruptor DIP 2 | Output Current (Approx.) |
|---|---|---|
| ON | ON | 100% (e.g., 3A) |
| OFF | ON | 75% (e.g., 2.25A) |
| ON | OFF | 50% (e.g., 1.5A) |
| OFF | OFF | 25% (e.g., 0.75A) |
Note: The exact current percentage may vary slightly. Always match the current to your stepper motor's rated current to prevent overheating.
Microstepping Setting
Microstepping allows for smoother motor operation and finer resolution. The TB6560 supports full step, half step, 1/8 step, and 1/16 step modes.
| Interruptor DIP 3 | Interruptor DIP 4 | Microstepping Mode |
|---|---|---|
| ON | ON | Pas complet |
| OFF | ON | Half Step |
| ON | OFF | 1/8 pas |
| OFF | OFF | 1/16 pas |
Note: Higher microstepping values result in smoother motion but may require higher step pulse frequencies from your controller.
Instruccions de funcionament
- Engegada inicial: After all connections are secure and DIP switches are set, apply power to the board. The power indicator LED should illuminate.
- Control Signal Input: Send STEP pulses to the STEP input pin to move the motor. The DIR pin controls the direction of rotation. The ENA (Enable) pin, when active (typically low), enables the motor driver.
- Motor Movement: Observe the motor's response. If the motor does not move or moves erratically, refer to the Troubleshooting section.
- S'apagui: Always disconnect the power supply before making any changes to wiring or DIP switch settings.
Manteniment
- Neteja: Keep the board free from dust and debris. Use a soft, dry brush or compressed air for cleaning. Do not use liquid cleaners.
- Condicions ambientals: Operate the board in a dry, well-ventilated environment. Avoid extreme temperatures and high humidity.
- Dissipador de calor: Ensure the heatsink remains clear of obstructions to allow for efficient heat dissipation. Periodically check for dust buildup on the heatsink fins.
Resolució de problemes
| Problema | Causa possible | Solució |
|---|---|---|
| Motor does not move. | No power, incorrect wiring, ENA pin disabled, no STEP pulses. | Check power supply, verify all wiring connections, ensure ENA is active, confirm STEP pulses are being sent. |
| Motor moves erratically or skips steps. | Insufficient current, excessive speed, incorrect microstepping, loose connections. | Increase current setting (if safe for motor), reduce step pulse frequency, verify microstepping settings, check all connections. |
| El motor es sobreescalfa. | Current setting too high, inadequate cooling. | Reduce current setting via DIP switches, ensure proper ventilation around the heatsink. |
| La placa no s'encén. | Sense font d'alimentació, volum incorrectetage, reversed polarity. | Verify power supply connection and voltage, check for correct polarity (V+ to positive, V- to negative). |
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.