ELEGOO 8-Channel 5V DC Relay Module Instruction Manual

1. Producte acabatview

The ELEGOO 8-Channel 5V DC Relay Module is designed for controlling various electrical loads using a microcontroller. It features 8 independent relays, each with normally open (NO) and normally closed (NC) contacts, and is optically isolated for enhanced safety and interference protection. This module is compatible with a wide range of microcontrollers including 8051, AVR, PIC, DSP, ARM, and MSP430.

Figure 1: ELEGOO 8-Channel Relay Module product packaging.

Característiques principals:

• 8-channel 5V DC relay interface board.
• Each channel requires approximately 70mA drive current.
• Equipped with high-current relays: 230V AC 10A, 30V DC 10A.
• Normally open and normally closed contacts available for each relay.
• Jumper selectable for TTL high or low level trigger.
• Power indicator and individual status indicators for each channel.
• Integrated freewheeling diode to protect the coil.
• Standard interface for direct control by microcontrollers.
• Optically isolated channels for safety and anti-interference.

2. Configuració i connexions

This section details the physical connections required to integrate your ELEGOO 8-Channel Relay Module into your project.

2.1 Components del mòdul

The module consists of:

• Relleus: Eight individual 5V relays.
• Pins d'entrada: VCC, GND, IN1-IN8.
• Terminals de sortida: Normally Open (NO), Common (COM), Normally Closed (NC) for each relay.
• LED indicador d'alimentació: Illuminates when the module is powered.
• LED indicadors d'estat: One for each relay, indicating its activation status.
• Jumper (JD-VCC): Used to select the power source for the relay coils (isolated or shared with logic).

Figura 2: Angle view of the ELEGOO 8-Channel Relay Module, showing relays and input pins.

Figura 3: De dalt a baix view of the module, illustrating component layout and pin labels.

2.2 Font d'alimentació

The module requires a 5V DC power supply. It is recommended to use a separate power supply for the relay coils to prevent interference with the microcontroller, especially when switching high-current loads.

• Shared Power (Default): If the JD-VCC jumper is in place, the relay coils are powered by the same 5V supply as the logic circuit (VCC pin). This is suitable for low-power applications where isolation is not critical.
• Isolated Power: For better stability and to avoid potential noise feedback to the microcontroller, remove the JD-VCC jumper. Connect an external 5V DC power supply to the JD-VCC and GND pins on the module. The VCC pin will still connect to your microcontroller's 5V output to power the optocouplers.

Figure 4: Close-up of the JD-VCC jumper and power input terminals.

2.3 Input Connections (Microcontroller)

Connect the IN1 to IN8 pins of the relay module to the digital output pins of your microcontroller (e.g., Arduino, Raspberry Pi). Each IN pin controls one relay.

• Nivell d'activació: The module can be configured to trigger on a high (+5V TTL) or low (GND) signal. This is typically set by a jumper on the module (often labeled S1, S2, etc., or indicated by the silkscreen). Refer to the module's silkscreen for specific jumper settings.
• When an input pin (e.g., IN1) receives the trigger signal (high or low, depending on configuration), the corresponding relay will activate.

Figure 5: Relay module connected to an Arduino board.

2.4 Output Connections (Load)

Each relay has three terminals for connecting your load:

• COM (Comú): Connect one side of your load's power source here.
• NO (normalment obert): The circuit is open (disconnected) when the relay is inactive. It closes (connects to COM) when the relay is activated.
• NC (normalment tancat): The circuit is closed (connected to COM) when the relay is inactive. It opens (disconnects from COM) when the relay is activated.

Choose between NO and NC depending on whether you want the load to be ON or OFF by default when the relay is not activated.

3. Funcionament

Once connected, the ELEGOO 8-Channel Relay Module operates by receiving control signals from your microcontroller.

3.1 Relay Activation

To activate a relay, send the appropriate digital signal (HIGH or LOW, depending on your module's trigger configuration) from your microcontroller to the corresponding IN pin. For example, if configured for low-level trigger, sending a LOW signal to IN1 will activate Relay 1.

3.2 Indicadors d'estat

Each relay has an associated LED that illuminates when the relay is activated, providing visual feedback on its status.

3.3 Switching Loads

When a relay activates, its internal switch changes state, connecting COM to NO and disconnecting COM from NC (or vice-versa). This allows you to control AC or DC loads up to the specified current and voltage ratings (230V AC 10A, 30V DC 10A).

Precaució: Always ensure the load's voltage and current ratings do not exceed the relay's maximum specifications. Working with AC mains voltage can be dangerous; exercise extreme caution and consult a qualified electrician if unsure.

4. Manteniment

The ELEGOO 8-Channel Relay Module is designed for durability and requires minimal maintenance.

• Mantenir net: Ensure the module is free from dust and debris. Use a soft, dry brush or compressed air for cleaning.
• Condicions ambientals: Operate the module within its specified temperature range (up to 85°C). Avoid exposure to excessive moisture or corrosive environments.
• Integritat de la connexió: Reviseu periòdicament totes les connexions dels cables per assegurar-vos que estiguin ben fixades i que no presentin corrosió.
• Inspecció de components: Visually inspect the relays and other components for any signs of damage or overheating.

5. Solució De Problemes

If you encounter issues with your ELEGOO 8-Channel Relay Module, consider the following troubleshooting steps:

• Relé no activat:
  • Verify the 5V DC power supply to the module (VCC and GND).
  • Check the control signal from your microcontroller to the IN pin. Ensure it's the correct trigger level (HIGH or LOW) as configured.
  • Confirm the JD-VCC jumper is correctly set for your power configuration (shared or isolated).
  • Test the relay with a simple direct 5V signal to its IN pin and GND to confirm the relay itself is functional.
• Càrrega no commutadora:
  • Ensure the relay activates (check the status LED).
  • Verify the load connections to the COM, NO, or NC terminals are correct and secure.
  • Check the load's power supply.
  • Confirm the load's voltage and current are within the relay's specifications.
• Interference or Unstable Operation:
  • If experiencing erratic behavior, especially with high-current loads, ensure you are using an isolated power supply for the relay coils (remove JD-VCC jumper and provide external 5V to JD-VCC and GND).
  • Ensure proper grounding of all components in your circuit.
• Audible Noise from Relays:
  • Relays inherently produce a clicking sound when switching. This is normal.
  • If the noise is excessive or constant when it shouldn't be, check for rapid switching or unstable control signals.

6. Especificacions tècniques

The following table details the technical specifications of the ELEGOO 8-Channel 5V DC Relay Module:

7. Informació de la garantia

The ELEGOO 8-Channel 5V DC Relay Module comes with a 1-year manufacturer's warranty. Please retain your proof of purchase for warranty claims. For detailed warranty terms and conditions, please refer to the official ELEGOO weblloc o contacteu amb el servei d'atenció al client.

8. Atenció al client

For technical assistance, troubleshooting, or further inquiries regarding your ELEGOO 8-Channel 5V DC Relay Module, please visit the official ELEGOO website or contact their customer support team. You can often find additional resources, tutorials, and FAQs on the brand's support pages.

Fabricant: ELEGOO

Model: FR-EL-SM-005

ASIN: B06XL1F53G