Fuers TL-2600 Fake Camera Instruction Manual

1. Producte acabatview

The Fuers TL-2600 is a high-quality, durable dummy surveillance camera designed to deter potential intruders. It features a realistic appearance, a flashing LED light, and is suitable for both indoor and outdoor use. This device provides a cost-effective solution to enhance security visibility without the complexity of a real surveillance system.

Característiques principals:

• Disseny realista: High resemblance to actual security cameras.
• Llum LED intermitent: Simulates active surveillance, powered by 2 AAA batteries (not included).
• Construcció duradora: Made from high-quality ABS material, weather-resistant for outdoor use.
• Angle ajustable: Features a mounting bracket allowing for 90° vertical and 360° horizontal rotation.
• Fàcil instal·lació: No wiring required, mounts quickly to walls or ceilings.

Image 1.1: The Fuers TL-2600 Fake Camera featuring a red flashing LED light, simulating active operation.

Image 1.2: The camera's adjustable bracket allows for 90-degree vertical and 360-degree horizontal rotation for optimal positioning.

2. Contingut del paquet

Si us plau, verifiqueu que tots els elements que s'enumeren a continuació estiguin inclosos al vostre paquet:

• 1 x Fuers TL-2600 Dummy Camera Unit
• 1 x Suport de muntatge (preinstal·lat)
• 3 x cargols de muntatge
• 3 x endolls de paret
• 1 x CCTV Warning Sticker

Nota: 2 x AAA batteries are no inclòs i s'han de comprar per separat.

Image 2.1: Contents of the package including the dummy camera, mounting hardware, and a CCTV sticker. Dimensions are also shown.

3. Configuració

3.1 Instal·lació de la bateria

1. Locate the battery compartment on the underside of the camera body.
2. Obriu amb cura la tapa del compartiment.
3. Insert two (2) AAA batteries (not included) into the compartment, ensuring correct polarity (+/-).
4. Close the battery compartment cover securely. The LED light should begin flashing immediately.

Imatge 3.1: View of the battery compartment opened to insert two AAA batteries.

Image 3.2: Step-by-step guide for installing batteries into the dummy camera.

3.2 Muntatge de la càmera

1. Choose a suitable location for installation, such as a wall or ceiling, ensuring good visibility and deterrence.
2. Position the mounting bracket at the desired location and mark the three screw holes.
3. Drill pilot holes at the marked spots. For masonry or drywall, insert the provided wall plugs.
4. Fixeu el suport de muntatge a la superfície amb els cargols proporcionats.
5. Adjust the camera angle as needed (refer to Section 4.1).
6. Affix the included CCTV warning sticker in a prominent location nearby to further enhance deterrence.

4. Instruccions de funcionament

4.1 Ajust de l'angle de la càmera

The camera's mounting bracket allows for flexible positioning:

• Ajust vertical: Loosen the side screw on the bracket to tilt the camera up or down (up to 90°). Tighten the screw once the desired angle is achieved.
• Ajust horitzontal: The base of the bracket allows for full 360° rotation. Simply rotate the camera body to face the desired direction.

4.2 LED intermitent

Once batteries are correctly installed, the red LED light will automatically begin to flash continuously. There is no separate on/off switch for the LED. The flashing LED simulates the operation of a real security camera, enhancing its deterrent effect.

5. Manteniment

• Substitució de la bateria: Replace the two AAA batteries when the LED light stops flashing or becomes dim. Always use fresh batteries for optimal performance.
• Neteja: Wipe the camera body and lens area with a soft, damp drap per eliminar la pols i la brutícia. Eviteu utilitzar productes químics aggressivs o netejadors abrasius.
• Resistència a la intempèrie: While designed for outdoor use, extreme weather conditions (e.g., heavy storms, prolonged direct sunlight) may affect its lifespan. Periodically check the unit for any signs of wear or damage.

6. Solució De Problemes

• LED Not Flashing:
  • Comproveu si les piles estan instal·lades correctament amb la polaritat correcta.
  • Substituïu-les per piles AAA noves.
• Camera Feels Loose After Mounting:
  • Ensure all mounting screws are tightened securely.
  • If mounted on drywall, ensure wall plugs are properly seated.

7. Especificacions