BOYA BY-WXLR8 UHF Wireless XLR Transmitter User Manual

1. Introducció

The BOYA BY-WXLR8 is a compact UHF wireless XLR transmitter designed to convert any wired XLR microphone into a wireless microphone. It is compatible with the BOYA BY-WM6 and BY-WM8 wireless microphone systems, specifically the RX8 and SPRX8 receivers. This manual provides essential information for the proper setup, operation, and maintenance of your BY-WXLR8 transmitter.

2. Producte acabatview

2.1 Components

• BY-WXLR8 Transmitter Unit
• XLR Connector (for microphone input)
• Line In Jack (3.5mm)
• Pantalla LCD
• Control Buttons (SET, UP, DOWN)
• Botó d'encesa/silenciació
• Compartiment de la bateria

2.2 Característiques clau

• UHF transmission for stable and interference-free audio.
• 48 selectable channels to avoid signal conflicts.
• Converts standard XLR microphones into wireless units.
• Includes a 3.5mm Line In jack for additional audio sources.
• Clear LCD display for channel and battery status.

Figura 1: Frontal view of the BY-WXLR8 transmitter, showing the LCD display and control buttons for channel selection and settings.

Figure 2: Detail of the XLR input connector and the 3.5mm Line In jack, indicating where to connect a microphone or external audio source.

3. Configuració

3.1 Instal·lació de la bateria

1. Localitzeu el compartiment de la bateria a la part posterior del transmissor.
2. Obriu la tapa del compartiment de la bateria.
3. Introduïu dues piles AA, assegurant-vos de la polaritat correcta (+/-).
4. Tanqueu bé la tapa del compartiment de la bateria.

Figure 3: The BY-WXLR8 transmitter with its battery compartment open, showing the slots for two AA batteries.

3.2 Connexió d’un micròfon

1. Align the XLR connector of your microphone with the XLR input on the BY-WXLR8 transmitter.
2. Push the microphone firmly into the transmitter's XLR input until it clicks into place.
3. To remove, press the release button on the XLR connector and pull the microphone out.

Figure 4: The BY-WXLR8 transmitter shown with a standard XLR microphone connected, illustrating its function as a wireless adapter.

3.3 Engegada/apagada

• To power on: Press and hold the 'POWER/MUTE' button for approximately 2 seconds. The LCD display will illuminate.
• To power off: Press and hold the 'POWER/MUTE' button for approximately 2 seconds until the display turns off.

4. Instruccions de funcionament

4.1 Selecció de canals

The BY-WXLR8 offers 48 UHF channels to minimize interference. To select a channel:

1. With the unit powered on, press the 'SET' button to enter channel selection mode. The current channel number will flash on the LCD.
2. Use the 'UP' and 'DOWN' buttons to navigate through the available channels.
3. Once your desired channel is selected, press 'SET' again to confirm and exit channel selection mode. Ensure your receiver is set to the same channel.

4.2 Funció de silenci

To temporarily mute the audio transmission:

• While the unit is powered on, short press the 'POWER/MUTE' button. The display will indicate 'MUTE'.
• Short press the 'POWER/MUTE' button again to unmute.

4.3 Using the Line In Jack

The 3.5mm Line In jack allows you to connect external audio sources directly to the transmitter. This input can be used simultaneously with the XLR microphone input, depending on the system's configuration.

5. Manteniment

5.1 Neteja

• Feu servir un drap suau i sec per netejar l'exterior del transmissor.
• No utilitzeu netejadors líquids ni dissolvents, ja que poden fer malbé el dispositiu.

5.2 Cura de la bateria

• Traieu les piles si no heu d'utilitzar la unitat durant un període prolongat per evitar fuites.
• Replace batteries when the low battery indicator appears on the LCD display.

5.3 Emmagatzematge

• Guardeu el transmissor en un lloc fresc i sec, allunyat de la llum solar directa i de temperatures extremes.
• Avoid storing in dusty environments.

6. Solució De Problemes

6.1 No Audio Signal

• Ensure the transmitter is powered on and has fresh batteries.
• Verify that the microphone is securely connected to the XLR input.
• Check that the transmitter and receiver are set to the same channel.
• Confirm the transmitter is not in mute mode.

6.2 Interference or Poor Audio Quality

• Try changing to a different channel on both the transmitter and receiver to avoid conflicting frequencies.
• Ensure there are no large metal objects or other wireless devices operating nearby that could cause interference.
• Reduir la distància entre l'emissor i el receptor.

7. Especificacions

Figure 5: The back of the BY-WXLR8 transmitter, displaying the model number and frequency range information.

8. Garantia i Suport

Information regarding product warranty and customer support was not provided in the source material. For detailed warranty terms, technical support, or service inquiries, please refer to the official BOYA weblloc web o poseu-vos en contacte amb el vostre distribuïdor autoritzat.