SOMMER Pearl 4018 Garage Door Remote Control User Manual

1. Introducció

This manual provides instructions for the safe and efficient operation, setup, and maintenance of your SOMMER Pearl 4018 4018V000 TX55-868-4 garage door remote control. This device utilizes the SOMloq2 radio system and is compatible with Somloq Rollingcode systems, as well as Pro Teckentrup Drive models 4020, 4026, and 4031 Slider.

Figura 1: SOMMER Pearl 4018 4018V000 TX55-868-4 Remote Control. This image shows the compact, modern design of the remote control, featuring four buttons and a stainless steel application.

2. Informació de seguretat

• Keep the remote control out of reach of children to prevent accidental operation of the garage door.
• No permeteu que els nens juguin amb el comandament a distància ni amb l'obridor de la porta del garatge.
• Ensure the garage door is visible and clear of obstructions before operating.
• Do not operate the garage door if people or objects are in its path.
• Elimineu les piles d'acord amb la normativa local. No incinereu les piles.
• Avoid exposing the remote control to extreme temperatures, moisture, or direct sunlight.

3. Contingut del paquet

Verifiqueu que tots els elements siguin presents al vostre paquet:

• SOMMER Pearl 4018 4018V000 TX55-868-4 Remote Control (quantity as purchased, typically 2 units)
• 3V CR2032 Lithium-metal battery (pre-installed or included)

4. Configuració i programació

The SOMMER Pearl 4018 remote control must be programmed to your garage door opener receiver. The exact programming steps may vary slightly depending on your specific SOMMER garage door opener model. Refer to your garage door opener's manual for precise instructions. A common programming method is outlined below:

1. Localitza el receptor: Identify the garage door opener's motor unit. On the motor unit, locate the "Learn" or "Program" button. This button is often small and may be recessed.
2. Activa el mode d'aprenentatge: Press and immediately release the "Learn" or "Program" button on your garage door opener. The indicator light on the opener will typically illuminate or flash, indicating it is in learn mode. You usually have about 30 seconds to complete the next step.
3. Programa el comandament a distància: Within the learn mode timeframe, press and hold the desired button on your SOMMER Pearl 4018 remote control that you wish to use for operating the garage door.
4. Confirma la programació: Release the button on the remote control once the garage door opener's indicator light flashes or changes color, or if the garage door moves slightly. This indicates successful programming.
5. Prova de funcionament: Premeu el botó programat del comandament a distància per assegurar-vos que funciona correctament la porta del garatge.
6. Programa comandaments a distància addicionals: Repeat these steps for any additional SOMMER Pearl 4018 remote controls you wish to program.

Note: If your garage door opener has a different programming procedure (e.g., using a master remote or a specific sequence), please consult your opener's manual.

5. Instruccions de funcionament

Once programmed, operating your SOMMER Pearl 4018 remote control is straightforward:

• Obrint/tancant la porta: Press the programmed button on your remote control once. The garage door will begin to open or close.
• Aturar la porta: Press the same programmed button again while the door is in motion to stop it.
• Portes múltiples: If you have programmed multiple garage doors to different buttons on your remote, press the corresponding button for the desired door.
• Interval: The remote control has an approximate range of 50-140 meters, depending on environmental conditions and obstructions.

6. Manteniment

6.1. Substitució de la bateria

The SOMMER Pearl 4018 remote control uses a 3V CR2032 Lithium-metal battery. When the remote's range decreases significantly or it stops responding, it is likely time to replace the battery.

1. Obriu el Casing: Obriu amb cura el comandament a distància casing. This usually involves prying it open with a small flat-head screwdriver or a similar tool at a designated notch.
2. Treure la bateria antiga: Note the orientation of the old CR2032 battery (positive (+) side up or down). Gently remove the old battery.
3. Inseriu una bateria nova: Insert a new 3V CR2032 Lithium-metal battery, ensuring the correct polarity. The positive (+) side typically faces upwards.
4. Tanca Casing: Enganxa el comandament a distància casintorneu a unir-se de manera segura.
5. Prova: Test the remote control to ensure it functions correctly with the new battery.

6.2. Neteja

Clean the remote control with a soft, dry cloth. Do not use abrasive cleaners or allow moisture to enter the casing.

7. Solució De Problemes

8. Especificacions

• Model: Pearl 4018 4018V000 TX55-868-4
• Sistema de ràdio: SOMloq2
• Botons: 4
• Freqüència de ràdio: FM 868.8 MHz, FM 868.95 MHz
• Interval: Approx. 50-140 meters (environment dependent)
• Dimensions: 79 x 26 x 13 mm (3.11 x 1.02 x 0.51 polzades)
• Tipus de bateria: 3V CR2032 Lithium-metal
• Pes: 40 g (1.41 oz)
• Compatibilitat: Somloq Rollingcode system, Pro Teckentrup Drive (compatible with 4020, 4026, 4031 Slider)

9. Garantia i Suport

For warranty information and technical support, please refer to the documentation provided with your original purchase or contact SOMMER customer service directly. Contact details can typically be found on the manufacturer's official weblloc.