1. Introducció
Welcome to the user manual for your Thincol Shore A Durometer Tester. This digital hardness meter is designed for accurate measurement of various soft materials such as rubber, gel, tires, plastics, leather, and wax. Please read this manual thoroughly before operating the device to ensure proper use and longevity.
2. Producte acabatview
2.1 Característiques clau
- Pantalla digital per a lectures fàcils i precises.
- Measures hardness of general rubber, synthetic rubber, soft rubber, multi-element grease, leather, and wax.
- Compact and pocket-sized for portability.
- Power switch allows unit change and reset at any position.
- High accuracy with a scale value of 0-100 degrees.
2.2 Components
The Shore A Durometer Tester consists of a main body with an LCD display, control buttons, and an indenter for measurement.
3. Configuració
3.1 Instal·lació de la bateria
The Shore A Durometer Tester requires one 1.5V button battery (LR44 type) for operation. This battery is no inclòs al paquet.
- Localitza el compartiment de la bateria al dispositiu, normalment a la part posterior o lateral.
- Obriu la tapa del compartiment de la bateria.
- Insert the 1.5V LR44 button battery, ensuring correct polarity (+/-).
- Tanqueu bé la tapa del compartiment de la bateria.
4. Instruccions de funcionament
4.1 Encès/Apagat
Premeu el botó OFF/ON button located on the front panel to power the device on or off.
4.2 Zeroing the Device
Before each measurement, it is crucial to zero the device to ensure accuracy.
- Ensure the indenter is not touching any surface.
- Check the LCD display. If it does not show '000', press the ZERO botó per reiniciar-lo.
4.3 Verification (Calibration Check)
To verify the device's calibration, perform the following check:
- Press the hardness tester firmly onto a flat, rigid surface such as a glass plate.
- Ensure the end face of the pressing needle and the bottom face of the pressing foot are in close contact with the glass plate.
- The display should read '100' degrees. If it does not, the device may require servicing or recalibration.
4.4 Prendre una mesura
Follow these steps to take an accurate hardness measurement:
- Assegureu-vos que el sample material is placed on a firm, flat surface.
- Position the indenter at least 12mm away from the edge of the sample.
- Press the indenter firmly and vertically onto the sample material. Apply steady pressure until the indenter is in full contact with the sample.
- Read the measurement displayed on the LCD within 1 second of full contact.
4.5 Consideracions importants
- When the indicated value of the Type A hardness tester is lower than 10 degrees, the reading is considered inaccurate and should not be used.
- Eviteu deixar caure el dispositiu o sotmetre-lo a forts impactes.
- No exposeu el dispositiu a temperatures o humitat extremes.
5. Manteniment
Proper maintenance ensures the longevity and accuracy of your Shore A Durometer Tester.
- After each use, wipe the hardness tester clean with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Store the device in its original instrument box when not in use.
- Keep the device in a dry place, away from direct sunlight and moisture, to prevent damage to electronic components.
- If the device will not be used for an extended period, remove the battery to prevent leakage.
6. Solució De Problemes
| Problema | Causa possible | Solució |
|---|---|---|
| El dispositiu no s'encén. | La bateria està morta o mal instal·lada. | Check battery polarity. Replace with a new 1.5V LR44 button battery. |
| Display shows erratic readings or does not zero. | Indenter is touching a surface during zeroing. Device needs reset. | Ensure indenter is free, then press the ZERO button. If problem persists, replace battery. |
| Readings are consistently below 10 degrees. | Material is too soft for Shore A scale, or measurement technique is incorrect. | Note that readings below 10 degrees are inaccurate for Shore A. Consider if a different durometer type (e.g., Shore OO) is needed for extremely soft materials. Review measurement steps. |
7. Especificacions
| Propietat | Valor |
|---|---|
| Tipus | Digital display Hardness tester (Type A) |
| Interval | 0-100° |
| Precisió | 0.1° |
| Dividint el valor | 0.1° |
| Interval de mesura | 0-100° |
| Model de bateria | 1.5V button battery (LR44, not included) |
| Dimensions del producte | 56 x 85 x 25 mm (2.2 x 3.3 x 1 polzades) |
| Pes | Aprox. 197 g (6.9 oz) |
| Número de model de l'article | Thincol7akvurmgws |
| ASIN | B07SHB5KRP |
| Fabricant | Thincol |
| País d'origen | Xina |
8. Contingut del paquet
The standard package for your Shore A Durometer Tester includes:
- 1 x Shore A Durometer Tester (battery not included)
- 1 x Caixa d'emmagatzematge
9. Garantia i Suport
For warranty information, technical support, or any inquiries regarding your Thincol Shore A Durometer Tester, please refer to the contact information provided on the product packaging or reach out to the seller directly. Keep your purchase receipt as proof of purchase for warranty claims.