NEO Z-Wave Plus Smart Light Switch User Manual

1. Introducció

This manual provides comprehensive instructions for the installation, setup, operation, and maintenance of your NEO Z-Wave Plus Smart Light Switch. This intelligent device allows for remote control through a Z-Wave network and radio waves, integrating seamlessly into your smart home system. It requires a Z-Wave gateway controller to function.

The switch features two touch buttons, each capable of controlling an independent relay to turn devices on or off. Each gang supports a maximum of 16A. You can set timers for automated lighting and control the switch remotely.

2. Informació de seguretat

• ADVERTÈNCIA: Risc de descàrrega elèctrica. Installation should only be performed by a qualified electrician or a person with a thorough understanding of electrical systems.
• Disconnect power at the circuit breaker or fuse box before installation.
• Assegureu-vos que totes les connexions de cablejat siguin segures i que compleixin els codis elèctrics locals.
• Do not exceed the maximum load rating of 16A per gang.
• Aquest dispositiu està dissenyat només per a ús en interiors.
• Mantenir allunyat de l'aigua i la humitat excessiva.

3. Producte acabatview

The NEO Z-Wave Plus Smart Light Switch features a sleek touch panel design with integrated indicator lights for status feedback.

Figura 3.1: Frontal view of the NEO Z-Wave Plus Smart Light Switch, showing two touch-sensitive circles.

Figura 3.2: lateral view illustrating the thin 1mm tempered glass panel of the switch, highlighting its anti-shock and bending strength properties.

Figure 3.3: Detailed technical drawing showing the dimensions (120mm x 74mm x 37mm) and internal components of the smart light switch.

4. Instal·lació

Before beginning installation, ensure the power is OFF at the circuit breaker. This device is designed for in-wall installation in a standard electrical box.

4.1 Esquema de cablejat

The switch requires Live (Line), Load, and Neutral connections. A ground wire should also be connected for safety.

Figure 4.1: Simplified wiring diagram showing connections for Live, Load, and Neutral wires. Consult a qualified electrician if unsure.

4.2 Passos d'instal·lació

1. Apagueu l'alimentació: Locate the circuit breaker controlling the switch location and turn it OFF. Verify power is off using a voltage provador.
2. Treure l'interruptor antic: Traieu amb cura la placa de paret i l'interruptor existents de la caixa elèctrica. Desconnecteu els cables.
3. Wire the NEO switch: Connect the wires to the corresponding terminals on the NEO Z-Wave Plus Smart Light Switch.
   • Connect the Live (Line) wire to the 'L' terminal.
   • Connect the Load wire(s) to the 'L1' and 'L2' terminals (for 1st and 2nd gang respectively).
   • Connecteu el cable neutre al terminal 'N'.
   • Connect the Ground wire to the ground screw in the box.

   Note: Some users have reported issues with terminal design and mounting. Ensure wires are neatly tucked into the electrical box to prevent interference with the mounting plate. Spacers or washers may be needed between the back plate and the wall if the main unit clips do not seat properly.

4. Muntar l'interruptor: Secure the switch into the electrical box using the provided screws.
5. Attach faceplate: Encaixeu la placa frontal de vidre al mòdul de l'interruptor.
6. Restaurar l'energia: Torneu a encendre l'alimentació a l'interruptor.

5. Z-Wave Network Setup

The NEO Z-Wave Plus Smart Light Switch must be included (paired) into a Z-Wave network to enable smart control features. It works with most Z-Wave hubs, including SmartThings, Vera, Fibaro, HomeSeer, Iris, and Aeotec.

5.1 Inclusion (Pairing)

1. Ensure your Z-Wave gateway controller is in inclusion mode (refer to your gateway's manual for specific instructions).
2. On the NEO Smart Light Switch, quickly press one of the touch buttons three times. The indicator light will flash to confirm inclusion mode.
3. The gateway will detect and add the device. Once successfully included, the indicator light will stop flashing and show its normal status.

5.2 Exclusion (Unpairing)

1. Ensure your Z-Wave gateway controller is in exclusion mode.
2. On the NEO Smart Light Switch, quickly press one of the touch buttons three times. The indicator light will flash to confirm exclusion mode.
3. The gateway will remove the device from the network.

6. Instruccions de funcionament

The NEO Smart Light Switch offers both manual touch control and remote Z-Wave control.

6.1 Control manual

Simply touch the circular icons on the glass panel to toggle the connected lights or devices ON/OFF.

Figure 6.1: Indicator lights on the touch panel. When power is ON, the LED is red. When power is OFF, the LED is blue.

6.2 Control remot mitjançant Z-Wave Hub

Once paired with your Z-Wave hub, you can control the switch remotely using your hub's mobile application or other integrated smart home systems. This allows for scheduling, scene creation, and control from anywhere.

Figure 6.2: Illustration of a smartphone app controlling the smart light switch through a Z-Wave hub, enabling remote management.

7. Manteniment

The NEO Z-Wave Plus Smart Light Switch requires minimal maintenance.

• Neteja: To clean the glass panel, gently wipe it with a soft, damp cloth. Do not use abrasive cleaners or solvents, as these may damage the surface.
• Actualitzacions de firmware: Check your Z-Wave hub's documentation for information on potential firmware updates for connected devices.

8. Solució De Problemes

If you encounter issues with your NEO Z-Wave Plus Smart Light Switch, refer to the following common problems and solutions:

9. Especificacions

10. Garantia i Suport

For warranty information and technical support, please refer to the documentation included with your product packaging or visit the official NEO weblloc. Conserveu el rebut de compra per a reclamacions de garantia.