Introducció
This manual provides detailed instructions for the ASHATA DC 12V Digital Relay Board. This versatile module is designed for various timing and control applications, including delay, cycle timing, and intermittent timing. It features a dual LED display for clear indication of timing parameters and can handle a maximum working current of 10A and a maximum power of 1500W.
Setup and Wiring
Proper wiring is essential for the safe and correct operation of the relay board. Refer to the wiring diagram below for connection details.
Figura 1: Diagrama de cablejat. This diagram illustrates how to connect the DC 12V power source and the load to the relay board. Ensure correct polarity for the DC 12V input and proper connection of the load to the relay output terminals.
The relay board requires a DC 12V power supply. Connect the positive (+) terminal of your 12V DC power source to the '+' terminal on the board and the negative (-) terminal to the '-' terminal. The load (e.g., a light, motor, or other device) should be connected to the relay output terminals. The relay acts as a switch, controlling the power to your load. Ensure all connections are secure before applying power.
Figure 2: Terminal Blocks. Un primer pla view of the blue and green terminal blocks for power input and load connection.
Instruccions de funcionament
The ASHATA Digital Relay Board features a dual LED display and several buttons for configuration. Understanding these components is key to operating the device.
Figure 3: Front Panel Layout. This image highlights the LED indicator, Timing T1 display, Timing T2 display, Reset button, Set key, and adjustment buttons (+/-).
Funcions clau:
- LED Indicator (OUT): Illuminates when the relay is active.
- Timing T1 Display: Shows the primary timing value (red display).
- Timing T2 Display: Shows the secondary timing value (blue display).
- Botó de reset: Resets the current timing operation or settings.
- SET Key (Gear Icon): S'utilitza per entrar al mode de programació i confirmar la configuració.
- '+' Button (Up Arrow): Increases the timing value or navigates through options.
- '-' Button (Down Arrow): Decreases the timing value or navigates through options.
Setting Timing Parameters:
- Introduïu el mode de programació: Manteniu premut el botó SET key (gear icon) for a few seconds until the display starts flashing or shows a mode selection.
- Select Time Unit: Utilitza el '+' or '-' buttons to cycle through time units: seconds (S), minutes (M), or hours (H). Press SET per confirmar.
- Set T1 Value: The T1 display will flash. Use the '+' or '-' buttons to adjust the desired timing value for T1 (0-999). Press SET per confirmar.
- Set T2 Value: If applicable for the selected function mode, the T2 display will flash. Use the '+' or '-' buttons to adjust the desired timing value for T2 (0-999). Press SET per confirmar.
- Seleccioneu el mode de funció: The display will show a function code (e.g., P-1, P-2, etc.). Use the '+' or '-' buttons to select one of the 18 available function combinations (delay, timing, cycle, intermittent timing). Refer to the product's detailed function table for specific mode descriptions. Press SET to confirm and exit programming mode.
Once settings are confirmed, the module will begin operation according to the selected mode and timing parameters. The LED indicator will show the relay's status.
Manteniment
The ASHATA DC 12V Digital Relay Board is designed for low maintenance. To ensure optimal performance and longevity:
- Mantingueu el dispositiu net i lliure de pols i brutícia. Feu servir un drap suau i sec per netejar-lo.
- Avoid exposing the module to excessive moisture or extreme temperatures.
- Regularly check wiring connections to ensure they remain secure.
- No intenteu obrir la casing or modify the internal components, as this may void the warranty and cause damage.
Resolució de problemes
If you encounter issues with your ASHATA Digital Relay Board, refer to the following common problems and solutions:
| Problema | Causa possible | Solució |
|---|---|---|
| El dispositiu no s'encén. | Incorrect power connection or no power supply. | Verify DC 12V power supply is connected correctly and is active. Check polarity. |
| El relé no s'activa. | Incorrect function mode selected, timing values set to zero, or load not connected properly. | Review function mode and timing settings. Ensure the load is correctly wired to the relay output. |
| Display is blank or erratic. | Power fluctuations or internal fault. | Disconnect and reconnect power. If the issue persists, contact customer support. |
| No es pot canviar la configuració. | Not in programming mode. | Manteniu premut el botó SET key to enter programming mode. |
Especificacions
Below are the technical specifications for the ASHATA DC 12V Digital Relay Board:
- Model: ASHATAmei46std7w
- Entrada Voltage: DC 12V
- Corrent de treball màxim: 10A
- Potència màxima: 1500W
- Interval de temps: 0-999 seconds, 0-999 minutes, 0-999 hours (selectable)
- Modes de funció: 18 types (Delay, Timing, Cycle Timing, Intermittent Timing, etc.)
- Visualització: Dual LED (Red for T1, Blue for T2)
- Material: Plàstic
- Mida del producte: Aproximadament 3 x 9.7 x 5.2 cm (1.1 x 3.8 x 2.0 polzades)
- ASIN: B07X5L8PPP
- UPC/GTIN: 748904169309
Figura 4: Dimensions del producte. This image shows the approximate measurements of the relay board.
Informació de la garantia
ASHATA products typically come with a standard manufacturer's warranty. For specific warranty details, including duration and coverage, please refer to the documentation provided with your purchase or contact ASHATA customer support. Keep your proof of purchase for warranty claims.
Atenció al client
For further assistance, technical support, or inquiries regarding your ASHATA DC 12V Digital Relay Board, please contact ASHATA customer service. You can typically find contact information on the product packaging or the official ASHATA weblloc.