BIG RED TAM825051 Torin Hydraulic Low Profile Trolley Floor Jack User Manual

Introducció

This manual provides essential instructions for the safe and effective use of your BIG RED TAM825051 Torin Hydraulic Low Profile Trolley Floor Jack. This hydraulic floor jack is designed for lifting vehicles with a maximum capacity of 2.5 tons (5,000 lb). It features a low-profile design, a single piston quick lift pump, and a safety bypass system to prevent overloading. Please read and understand all instructions and safety warnings before operation.

Informació de seguretat

WARNING: Failure to heed these warnings may result in personal injury and/or property damage.

• Always wear ANSI-approved safety goggles during setup and use.
• No supereu la capacitat nominal de 2.5 tones (5,000 lliures).
• Utilitzeu només en una superfície dura i plana.
• Immediately after lifting, support the vehicle with appropriate jack stands. Do not rely solely on the hydraulic jack for support.
• No utilitzeu el gat per a altres finalitats que no siguin aixecar vehicles.
• Assegureu-vos que el fre d'estacionament del vehicle estigui accionat i que les rodes estiguin bloquejades abans d'aixecar-lo.
• Keep hands and feet clear of the jack and vehicle during lifting and lowering.
• No treballeu mai sota un vehicle suportat només per un gat.
• Do not modify the jack or use it with unauthorized attachments.

Contingut del paquet

Verify that all components are present before assembly and operation:

• Gat de sòl hidràulic
• 2-Piece Handle
• Manual d'usuari (aquest document)

Assemblea

The BIG RED TAM825051 floor jack requires minimal assembly, primarily attaching the handle.

1. Insert the lower handle section into the handle socket on the jack.
2. Align the holes and secure the handle with the provided pin or screw, if applicable.
3. Attach the upper handle section to the lower section, ensuring it is firmly connected.

Once assembled, the handle is used for both pumping the jack and operating the release valve.

Muntatge i preparació

Before using the jack, perform the following steps:

1. Purgar l'aire del sistema hidràulic: Before first use, or if the jack has been stored for a long time, it may be necessary to purge air from the hydraulic system. To do this, open the release valve by turning the handle counter-clockwise. Pump the handle several times to remove any trapped air. Close the release valve by turning the handle clockwise.
2. Inspect the Jack: Check for any visible damage, leaks, or loose parts. Do not use the jack if it appears damaged.
3. Preparar el vehicle: Park the vehicle on a hard, level surface. Engage the parking brake and place wheel chocks on the wheels that will remain on the ground.

Image: The BIG RED TAM825051 Torin Hydraulic Low Profile Trolley Floor Jack, showcasinpel seu disseny compacte i el seu acabat vermell.

Instruccions de funcionament

Aixecar el Vehicle

1. Position the jack under the vehicle's designated lifting point. Refer to your vehicle's owner's manual for correct lifting points.
2. Ensure the saddle of the jack is centered and securely contacting the lifting point.
3. Close the release valve by turning the handle clockwise until it is firm. Do not overtighten.
4. Bombeu la maneta amunt i avall per elevar el vehicle a l'alçada desitjada.
5. Once the vehicle is lifted, immediately place appropriately rated jack stands under the vehicle's frame at the manufacturer's recommended support points.
6. Slowly lower the vehicle onto the jack stands by gently turning the release valve counter-clockwise. Ensure the vehicle is stable on the jack stands before performing any work.

Image: The red BIG RED floor jack positioned under the side of a red car, ready for lifting. This demonstrates proper placement for vehicle support.

Baixant el Vehicle

1. Raise the vehicle slightly off the jack stands using the hydraulic jack.
2. Traieu amb cura els suports del gat de sota el vehicle.
3. Slowly turn the release valve counter-clockwise to gradually lower the vehicle to the ground. Control the lowering speed to prevent sudden drops.
4. Once the vehicle is fully lowered, remove the jack from under the vehicle.

Manteniment

Un manteniment regular garanteix la longevitat i el funcionament segur del vostre gat hidràulic.

• Lubricació: Keep all moving parts of the jack well-lubricated. Apply light oil to pivot points and axles periodically.
• Fluid hidràulic: Check the hydraulic fluid level regularly. To check, fully lower the jack, remove the oil filler plug, and ensure the fluid is at the correct level. Use only high-quality hydraulic jack oil. Do not use brake fluid or motor oil.
• Neteja: Keep the jack clean from dirt, grease, and corrosive materials.
• Emmagatzematge: Store the jack in a fully lowered position in a clean, dry area.

Imatge: Una imatge detallada view of the handle and release valve area of the BIG RED floor jack, highlighting key operational components.

Resolució de problemes

If you encounter issues with your jack, refer to the following common problems and solutions:

Especificacions

• Número de model: TAM825051
• Capacitat de càrrega: 2.5 tons (5,000 lb)
• Alçada mínima d'elevació: 3-3/8 inches (approximately 8.57 cm)
• Alçada màxima d'elevació: 14-15/16 inches (approximately 37.94 cm)
• Material: Acer d'aliatge
• Pes de l'article: 27.7 lliures (aproximadament 12.56 kg)
• Dimensions de l'article (LxWxH): 24.5 x 10.3 x 5.7 polzades (aproximadament 62.23 x 26.16 x 14.48 cm)
• Tipus de servei de vehicles: Car (Note: Not recommended for all SUVs and trucks due to height limitations)

Image: A visual representation of the BIG RED floor jack, indicating its minimum height of 3-3/8 inches and maximum height of 14-15/16 inches.

Garantia i Suport

This BIG RED TAM825051 Torin Hydraulic Low Profile Trolley Floor Jack includes a limited 1-year manufacturer warranty. For warranty claims, technical support, or replacement parts, please contact BIG RED customer service. Keep your purchase receipt as proof of purchase.