Producte acabatview
The DAYBETTER 44-Key Remote Control is designed to manage 12-24V DC 4-pin LED strip lights, offering a wide range of color and mode options. It features a dual-port connector, allowing control of one or two LED strips simultaneously.
DAYBETTER 44-Key Remote Control and Controller Box with LED Strip Lights
Contingut del paquet
- 1 comandament a distància IR de 44 tecles
- 1 x LED Controller Box (with two 4-pin output ports)
- 1 x adaptador de corrent
Instruccions de configuració
Follow these steps to properly set up your DAYBETTER LED strip light system.
- Step 1: Prepare the Remote Control. Before first use, locate the plastic insulation tab in the battery compartment of the 44-key remote control. Pull this tab out to activate the battery.
- Step 2: Connect LED Strips to the Controller. Ensure the power adapter is disconnected. Connect your 4-pin LED strip lights to the output ports on the LED controller box. Align the arrow on the LED strip connector with the arrow on the controller's output port. The controller box has two 4-pin ports, allowing connection of one or two LED strips.
- Step 3: Connect Power Adapter. Connect the power adapter to the DC input port on the LED controller box.
- Step 4: Connect to Power Source. Plug the power adapter into a suitable 12-24V DC power outlet.
Removing the plastic insulation tab from the remote control battery compartment.
Proper alignment of 4-pin LED strip connector with the controller port, ensuring arrow-to-arrow connection.
Primer pla view of the LED controller box, showing the DC power input port and IR sensor.
Diagram illustrating the complete connection process: Power Adapter to IR Receiver, IR Receiver to LED Controller, and LED Controller to LED Strip Lights, highlighting correct 4-pin connector orientation.
Operating Your LED Controller
The 44-key remote control allows for comprehensive control over your LED strip lights. Ensure the remote is pointed directly at the IR sensor on the controller box within approximately 30 feet for optimal functionality.
Diagram of the 44-key remote control, detailing the function of each button for color selection, brightness adjustment, and mode changes.
- Encès/apagat: Premeu el botó ON/OFF botó per encendre o apagar els llums.
- Ajust de brillantor: Utilitza el Brillantor cap amunt (up arrow) and Brillantor avall (down arrow) buttons to adjust the light intensity (7 levels).
- Colors estàtics: Select from 20 static colors by pressing the corresponding color buttons.
- RGB Adjustment: Utilitza el R, G, B buttons to fine-tune red, green, and blue color levels.
- Quick/Slow: Adjust the speed of dynamic modes (Jump3, Jump7, Fade3, Fade7, Flash) using the RÀPID i LENTA botons.
- Mode automàtic: Premeu AUTO for automatic color cycling through various modes.
- Mode de flaix: Activates a rapid flashing effect.
- Fade Modes:
- FADE7: Gradually fades through 7 colors.
- FADE3: Gradually fades through 3 colors.
- Modes de salt:
- JUMP7: Jumps between 7 colors.
- JUMP3: Jumps between 3 colors.
- DIY Buttons (DIY1-DIY6): These buttons allow you to save custom color settings. To set a custom color:
- Premeu a DIY botó.
- Utilitza el R, G, B adjustment arrows to create your desired color.
- Premeu el mateix DIY button again to save the color.
Manteniment
- Neteja: Use a dry, soft cloth to clean the controller and remote. Do not use liquid cleaners or abrasive materials.
- Substitució de la bateria: If the remote control's range or responsiveness decreases, replace the battery (CR2025 coin cell, not included). Ensure correct polarity.
- Emmagatzematge: Guardeu el dispositiu en un lloc fresc i sec, allunyat de la llum solar directa i de temperatures extremes quan no l'utilitzeu durant períodes prolongats.
Resolució de problemes
| Problema | Solució |
|---|---|
| Els llums no s'encenen. | Check power connections. Ensure the power adapter is plugged in and the LED strips are correctly connected (arrow to arrow). Verify the remote control battery is active and correctly inserted. |
| El comandament a distància no respon. | Ensure the plastic insulation tab has been removed from the remote. Point the remote directly at the IR sensor on the controller box. Replace the remote control battery if necessary. The effective range is approximately 30 feet. |
| Les llums són tènues o parpellejant. | Check the power adapter for sufficient voltage (12-24V DC). Ensure all connections are secure. Reduce the length of the LED strip if it exceeds the controller's maximum current capacity (6A). |
| Incorrect colors displayed. | Ensure the 4-pin connectors are aligned correctly (arrow to arrow). Disconnect and reconnect the LED strips. |
| Only one LED strip works. | Verify both 4-pin connectors are properly inserted into the controller's dual ports. Check the connections of the non-working strip. |
Especificacions del producte
- Model: DRF-0362-W
- Marca: MILLOR DIA
- Tipus de controlador: 44-Key IR Remote Control
- Entrada Voltage: 12-24V DC
- Ports de sortida: 2 x 4 pins
- Corrent màxima: 6A
- Mètode de control: Infrared (IR) Remote
- Distància remota: Approximately 30 feet (line of sight required)
- Material: Plàstic
- Ús interior/exterior: Interior
- Característiques especials: Dimmable, 20 Static Colors, Dynamic Modes (Flash, Fade, Jump), DIY Color Saving
- Compatible LED Strips: 5050, 3528, 2835 (4-pin RGB)
Informació de la garantia
For warranty details, please refer to the product packaging or contact DAYBETTER customer service. Keep your purchase receipt as proof of purchase for any warranty claims.
Atenció al client
If you encounter any issues or have questions regarding your DAYBETTER 44-Key Remote Control, please contact DAYBETTER customer support through the retailer's platform or visit the official DAYBETTER weblloc d'assistència.