Taidacent TTL to CAN Bus Converter (STM32f103c8t6) User Manual

1. Introducció

This module converts a TTL signal into a CAN signal, simplifying data transmission for embedded systems. It eliminates the need to learn complex CAN protocols, thereby shortening development cycles and reducing costs. The module supports both 3.3V and 5V power supplies and features semi-hole technology for easy integration into various systems. It is equipped with a 32-bit ARM processor and a CAN level shifting chip, offering 14 sets of masking filters with five frame filtering methods each. Parameters are configured via simple AT commands, with only 6 instructions required. Its wide baud rate range enhances network adaptability.

2. Característiques del producte

• Processador: ARM processor with Cortex M3 core for enhanced data processing and lower power consumption. Integrated CAN controller for efficient transmission.
• Font d'alimentació: Compatible with 5V and 3.3V power supplies, featuring an LDO linear regulator.
• Velocitat de transmissió CAN: Supports 3Kbps to 1Mbps, fully compliant with CAN bus 2.0A and 2.0B specifications.
• Velocitat en baudios del port sèrie: Supports 4800bps to 460800bps.
• Sampling Point: Automatically adjusted to or near the CIA value.
• Filtrat: 14 sets of 32-bit shielding filters, freely configurable.
• Configuració: Parameters set via AT commands and saved after power down.
• Velocitat de transferència de dades: Over 600 frames per second.
• Recuperació: Offline self-recovery function.
• Configuració per defecte: Hardware and software restore default parameters.
• Message Data Length: 0-8 bytes, arbitrarily settable.
• Protecció: Includes surge protection circuit to suppress transient interference.
• Indicador d'estat: LED indicator shows 1 Hz in communication mode and 5 Hz in configuration mode.
• Nota de compatibilitat: The serial port is TTL 3.3V signal; not compatible with 232 signal. A 5V to 3.3V circuit is recommended for interfacing with 5V systems.

3. Configuració i connexions

Proper connection of the module is essential for correct operation. Refer to the pinout diagram and descriptions below for guidance.

Figura 3.1: Pinout diagram of the Taidacent TTL to CAN Bus Converter module, highlighting connection points.

Descripcions de pins:

• 5 V: Connect to a 5V power supply.
• 3.3 V: Connect to a 3.3V power supply.
• GND: Connect to power ground.
• CFG: Configuration pin. Set to 0 for configuration mode, 1 for working mode.
• TXD: Connect to the RXD pin of your target board (e.g., STM32).
• RXD: Connect to the TXD pin of your target board (e.g., STM32).
• CANL: Connect to the CANL signal line of the CAN network.
• CANH: Connect to the CANH signal line of the CAN network.

Nota important: The serial port of this module operates with a TTL 3.3V signal. It is not compatible with 232 signals. If integrating with a 5V system, it is strongly recommended to use a 5V to 3.3V level shifter circuit to prevent damage to the module or target board.

Figura 3.2: A dalt view of the module, showing the STM32 microcontroller and other components.

Figura 3.3: A baix view of the module, indicating pin labels for connection.

4. Instruccions de funcionament

4.1 modes de funcionament

• Mode de configuració: Set the CFG pin to 0. In this mode, the module accepts AT commands for parameter setup. The status indicator LED will flash at 5 Hz.
• Mode de treball: Set the CFG pin to 1. In this mode, the module performs TTL to CAN signal conversion. The status indicator LED will flash at 1 Hz.

4.2 Configuració del comandament AT

The module's parameters, such as CAN baud rate, serial port baud rate, and filter settings, are configured using a set of simple AT commands. There are only 6 instructions to manage the module's settings. These settings are saved automatically after power down, ensuring persistent configuration.

For detailed AT command syntax and usage, refer to the specific programming guide or datasheet provided by Taidacent (not included in this manual).

4.3 Transmissió de dades

Once configured and in working mode, the module facilitates high-speed data transfer between TTL serial and CAN bus interfaces. It supports data transfer speeds exceeding 600 frames per second. The message data length can be set arbitrarily from 0 to 8 bytes.

5. Manteniment

The Taidacent TTL to CAN Bus Converter module is designed for reliable operation with minimal maintenance. To ensure longevity and optimal performance:

• Mantingueu el mòdul net i lliure de pols i humitat.
• Eviteu exposar el mòdul a temperatures o humitat extremes.
• Ensure proper ventilation if enclosed in a casing.
• Manipuleu amb cura per evitar danys físics als components o a les unions de soldadura.

6. Solució De Problemes

• Sense comunicació:
  • Verify all power and signal connections (5V, 3.3V, GND, TXD, RXD, CANL, CANH) are secure and correct as per Section 3.
  • Ensure the CFG pin is set correctly for the desired mode (0 for configuration, 1 for working).
  • Check that the serial port of your target board is indeed TTL 3.3V. If it's a 5V system, confirm a level shifter is used.
  • Confirm baud rates (serial and CAN) are correctly configured and match the connected devices.
• Incorrect LED Indicator Behavior:
  • If the LED is not flashing as expected (1 Hz in working mode, 5 Hz in configuration mode), recheck the CFG pin setting and power supply.
• Mòdul no respon:
  • The module features offline self-recovery. Disconnect and reconnect power to attempt a reset.
  • You can restore hardware and software default parameters if configuration issues persist. Refer to the AT command documentation for the specific command to reset to factory defaults.
• Corrupció/errors de dades:
  • Verify CAN bus termination resistors are correctly implemented in your network, if applicable.
  • Check for electrical noise or interference in the environment. The module has surge protection, but extreme conditions can still affect performance.

7. Especificacions

8. Garantia i Suport

Specific warranty information for the Taidacent TTL to CAN Bus Converter (STM32f103c8t6) is not provided in this manual. For details regarding warranty coverage, technical support, or further assistance, please contact Taidacent directly or refer to their official website. You may also reach out to the retailer from whom the product was purchased.

Manufacturer: Taidacent