Hormann HSE 4 BS Hand Transmitter User Manual

1. Introducció

This manual provides essential information for the proper setup, operation, and maintenance of your Hormann HSE 4 BS Hand Transmitter. This device is designed for convenient control of compatible garage door and gate operators. Please read these instructions carefully before using the product to ensure safe and efficient operation.

2. Instruccions de seguretat

• Keep the hand transmitter out of reach of children to prevent accidental operation.
• The device is intended for use in dry environments only. Avoid exposure to moisture, rain, or extreme temperatures.
• Do not attempt to open or repair the hand transmitter yourself. Refer to qualified personnel for service.
• Ensure the area around the garage door or gate is clear before operating to prevent injury or damage.
• Eliminar les bateries usades d'acord amb la normativa local.

3. Contingut del paquet

Verifiqueu que tots els elements siguin presents al vostre paquet:

• 1x Hormann HSE 4 BS Hand Transmitter (Classic Grey Chrome)
• 1x CR2032 Lithium Button Cell Battery (pre-installed or included separately)
• 1x Key Ring

4. Producte acabatview

The Hormann HSE 4 BS Hand Transmitter is a compact and durable remote control featuring a high-gloss plastic surface with chrome-plated die-cast zinc caps. It is designed for ease of use with a single button operation.

Image showing the Hormann HSE 4 BS hand transmitter, a compact remote control with a high-gloss classic grey finish and chrome accents. It features a single button and a key ring attachment.

5. Configuració

5.1. Instal·lació de la bateria

The hand transmitter uses a 3V Lithium button cell battery, type CR2032. The battery is typically pre-installed. If replacement is needed:

1. Obriu amb cura la casing de l'emissor manual.
2. Traieu la bateria CR2032 antiga.
3. Insert the new CR2032 battery with the positive (+) side facing up.
4. Tanca el casing de manera segura.

5.2. Programming the Hand Transmitter

The HSE 4 BS hand transmitter supports both BiSecur radio and fixed code 868 MHz operation. The programming procedure depends on your specific garage door or gate operator model.

General Programming Steps (Refer to your operator's manual for detailed instructions):

1. Activate the programming mode on your garage door or gate operator. This usually involves pressing a 'P' or 'Learn' button on the operator's control unit. Consult your operator's manual for the exact location and procedure.
2. While the operator is in programming mode, press and hold the button on your HSE 4 BS hand transmitter that you wish to program.
3. Hold the button until the operator's indicator light confirms successful programming (e.g., flashes, changes color, or turns off).
4. Release the button on the hand transmitter.
5. Test the hand transmitter to ensure it operates the door or gate correctly.

For specific programming instructions for your Hormann operator, please refer to the operator's instruction manual or visit the official Hormann weblloc.

6. Instruccions de funcionament

To operate your garage door or gate:

1. Ensure you are within range of your garage door or gate operator.
2. Press the single button on the HSE 4 BS hand transmitter.
3. The door or gate will begin to open or close. Pressing the button again during operation will typically stop the movement.

7. Manteniment

7.1. Substitució de la bateria

When the range of your hand transmitter decreases significantly, or if the indicator light (if present) does not illuminate, it is likely time to replace the battery. Follow the steps outlined in Section 5.1 for battery installation.

7.2. Neteja

Clean the hand transmitter with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these can damage the surface.

8. Solució De Problemes

• Hand Transmitter Not Working: Check if the battery is correctly inserted and has sufficient charge. Replace the battery if necessary. Ensure the hand transmitter is properly programmed to your operator.
• Abast reduït: This often indicates a low battery. Replace the CR2032 battery. Obstructions between the hand transmitter and the operator's receiver can also reduce range.
• Door/Gate Not Responding: Verify that the operator itself is powered and functioning correctly. Check for any physical obstructions preventing the door or gate from moving.

If problems persist, consult your garage door or gate operator's manual or contact Hormann customer support.

9. Especificacions

10. Garantia i Suport

For information regarding warranty terms and conditions, please refer to the documentation provided with your garage door or gate operator, or visit the official Hormann website. If you require technical assistance or have questions not covered in this manual, please contact Hormann customer support.