Hantek DSO2D15 2-Channel Digital Storage Oscilloscope Instruction Manual

1. Introducció

The Hantek DSO2D15 is a 2-channel digital storage oscilloscope featuring a 150MHz bandwidth, 1GSa/s sampling rate, and 8M memory depth. It also includes a built-in 25MHz DDS waveform generator. This instrument is designed for various electronic testing and measurement applications, offering advanced trigger modes, serial protocol decoding, and automatic measurement functions.

This manual provides essential information for the safe and efficient operation of your DSO2D15 oscilloscope. Please read it thoroughly before use and retain it for future reference.

2. Informació de seguretat

Always observe the following safety precautions to prevent injury and avoid damage to the instrument or connected devices.

• Font d'alimentació: Ensure the oscilloscope is connected to a power source within the specified voltage range (100-240V AC, 50/60Hz). Use only the provided power cord or an approved equivalent.
• Posada a terra: The instrument must be properly grounded to prevent electric shock. Do not defeat the grounding feature of the power plug.
• Condicions ambientals: Operate the oscilloscope in a dry, well-ventilated area. Avoid exposure to extreme temperatures, humidity, dust, or corrosive gases.
• Voltage: Vol perillóstages are present inside the device. Do not remove the cover unless performed by qualified service personnel. Refer to the warning label on the rear panel.
• Sondes: Use only probes rated for the voltage and frequency being measured. Ensure probes are properly connected before making measurements.
• Neteja: Desconnecteu l'alimentació abans de netejar. Feu servir un drap suau i sec.amp tela. No utilitzeu netejadors abrasius ni dissolvents.
• Manteniment: Demaneu tot el servei a personal qualificat.

Figure 2.1: Rear panel of the DSO2D15, highlighting the power input and safety warning label regarding hazardous voltage.

3. Configuració

3.1 Desembalatge i inspecció

Carefully unpack the oscilloscope and all accessories. Inspect for any signs of damage during transit. If any damage is found, contact your supplier immediately.

3.2 Contingut del paquet

The standard package for the Hantek DSO2D15 includes the following items:

• Hantek DSO2D15 Oscilloscope Unit
• 1 PP150B 150MHz Probe
• 1 Hantek PP150 100MHz Probe (for 2nd channel)
• 1 cable USB
• 2 Clip Lines
• 1 US Power Cable (Note: Some units may include a European power cable. If so, a compatible US power cable will be required for operation in the US.)

Figure 3.1: The DSO2D15 oscilloscope unit shown with its various included accessories, such as probes, cables, and clip lines.

Figure 3.2: A closer look at the included oscilloscope probes, various clip lines, and a wire stripping tool, essential for connecting to circuits.

3.3 Connexió d'alimentació

1. Connect the provided power cable to the AC input on the rear panel of the oscilloscope.
2. Connecteu l'altre extrem del cable d'alimentació a una presa de corrent de CA amb connexió a terra.
3. Ensure the power switch (usually located near the AC input) is in the OFF position before connecting to power.

3.4 Connexió de la sonda

Connect the oscilloscope probes to the BNC input connectors on the front panel (CH1, CH2). Ensure a secure connection by twisting the BNC connector until it locks.

Before making measurements, perform probe compensation to ensure accurate readings. Refer to the "Probe Compensation" section in the Operating Instructions.

4. Instruccions de funcionament

4.1 Engegada/apagada

1. To power on, press the power switch located on the rear panel. The display will illuminate, and the system will boot up.
2. Per apagar, premeu l'interruptor d'alimentació de nou.

4.2 Tauler frontal sobreview

The front panel of the DSO2D15 features a large display, control buttons, and input connectors. Familiarize yourself with the layout for efficient operation.

Figure 4.1: Front panel of the DSO2D15, showing the display, function buttons (F1-F6), vertical and horizontal controls, trigger controls, and channel inputs.

4.3 Basic Oscilloscope Functions

• Controls verticals: Ajusta el voltage per divisió (Volts/Div) i posició vertical per a cada canal (CH1, CH2).
• Controls horitzontals: Adjust time per division (Sec/Div) and horizontal position to control the time base.
• Sistema de disparador: Use the trigger controls to stabilize waveforms. Select trigger type (Edge, Pulse, Video, Slope, etc.), source, and level. The DSO2D15 offers 14 kinds of trigger modes.
• Acquisition Mode: Select between Normal, Peak Detect, and Average modes for waveform acquisition.
• Mides: Access automatic measurement functions (32 kinds available) to display parameters like frequency, period, Vpp, Vmax, Vmin, etc.
• Serial Protocol Decoding: The unit supports 5 kinds of serial protocol decoding. Refer to the on-screen menu for specific setup and analysis.

4.4 DDS Waveform Generator

The DSO2D15 includes a built-in 25MHz DDS waveform generator. This generator can produce various standard waveforms (sine, square, triangle, etc.) for testing circuits.

1. Connect the DDS output (labeled EXT TRIG/GEN OUT) to the circuit under test.
2. Access the generator menu via the front panel controls.
3. Select the desired waveform type, frequency, amplitude, and offset.
4. Enable the output to generate the waveform.

Note: The built-in DDS generator is suitable for general testing but should not be confused with a dedicated arbitrary waveform generator for complex signal generation.

5. Manteniment

5.1 Atenció general

• Mantingueu l'instrument net i sec.
• Eviteu deixar caure la unitat ni sotmetre-la a impactes forts.
• Emmagatzemar en un entorn sense pols quan no estigui en ús.

5.2 Neteja

To clean the exterior of the oscilloscope:

1. Desconnecteu el cable d'alimentació de la presa de CA.
2. Utilitzeu un drap suau lleugerament dampnetejat amb aigua o un netejador suau i no abrasiu.
3. Wipe the surfaces gently. Do not allow liquids to enter the instrument.
4. Assegureu-vos que la unitat estigui completament seca abans de tornar a connectar l'alimentació.

5.3 actualitzacions de microprogramari

Consulteu periòdicament el lloc web oficial de Hantek website for available firmware updates. Updating the firmware can improve performance, add features, or resolve known issues. Follow the instructions provided with the firmware update package carefully.

6. Solució De Problemes

This section addresses common issues you might encounter with your DSO2D15 oscilloscope.

7. Especificacions

The following are key technical specifications for the Hantek DSO2D15 oscilloscope:

• Ample de banda: 150 MHz
• Canals: 2 canals analògics
• SampTarifa de ling: 1 GSa/s (Real-time)
• Profunditat de memòria: 8M points
• Built-in DDS Waveform Generator: 25 MHz
• Modes d'activació: 14 types (Edge, Pulse, Video, Slope, etc.)
• Serial Protocol Decoding: 5 tipus
• Mesures automàtiques: 32 tipus
• Visualització: LCD TFT de 7 polzades
• Connectivitat: USB Host, USB Device

Físiques i Ambientals

• Dimensions del paquet: 14.3 x 8.25 x 7.75 polzades
• Pes de l'article: 6.14 lliures
• Fabricant: Qingdao Hantek Electronic Co., Ltd.
• Vol. Operatiutage: 100-240V AC, 50/60Hz
• Data de primera disponibilitat: 24 de març de 2021

8. Garantia i Suport

8.1 Informació de la garantia

Hantek products are typically covered by a limited warranty against defects in materials and workmanship. The specific terms and duration of the warranty may vary by region and retailer. Please retain your proof of purchase for warranty claims.

For detailed warranty information, please refer to the warranty card included with your product or visit the official Hantek weblloc.

8.2 Suport tècnic

If you encounter issues not covered in this manual or require further assistance, please contact Hantek technical support. You can typically find contact information on the official Hantek weblloc web o a través del vostre distribuïdor de productes.

When contacting support, please have your product model (DSO2D15) and serial number ready, along with a detailed description of the issue.

També podeu visitar el Hantek Store on Amazon per obtenir informació i recursos addicionals sobre el producte.