BESTTEN Almond Dimmer Light Switch User Manual

1. Producte acabatview

The BESTTEN Almond Dimmer Light Switch is designed to provide adjustable lighting levels for various bulb types. It supports both single-pole and 3-way applications and includes a decorator wall plate. This dimmer features a memory function to recall the last dimmed setting and an adjustable dimming range to prevent flickering.

Figure 1: BESTTEN Almond Dimmer Light Switch with included wall plate.

2. Contingut del paquet

• Interruptors de regulació
• Cargols
• Plaques de paret

3. Informació de seguretat

• ADVERTIMENT: Per evitar incendis, descàrregues elèctrices o la mort, desconnecteu l'alimentació a l'interruptor o a la caixa de fusibles i comproveu que estigui apagada abans de connectar el cablejat.
• Instal·leu segons tots els codis elèctrics nacionals i locals.
• Use only with compatible dimmable bulbs (LED, CFL, Incandescent, Halogen).
• Do not use with non-dimmable bulbs or motor-driven appliances like fans.
• Only one dimmer switch can be installed in a 3-way circuit.

4. Instruccions d'instal·lació

4.1 Wiring for Single-Pole Application

A single-pole application controls a light fixture from one location. Ensure power is off before proceeding.

Figure 2: Single-pole wiring diagram. Connect the hot wire to the silver screw, the load wire to the brass screw, and the ground wire to the green screw. No neutral wire is required.

4.2 Wiring for 3-Way Application

A 3-way application controls a light fixture from two locations. Only one dimmer switch can be installed in a 3-way circuit. Ensure power is off before proceeding.

Figure 3: 3-way wiring diagram. Connect the hot wire to the silver screw, the load wire to one brass screw, and the traveler wire to the other brass screw. Connect the ground wire to the green screw. No neutral wire is required.

4.3 Dimming Range Adjustment

This dimmer features an adjustable dimming range to optimize performance and eliminate flickering with various dimmable LED/CFL bulbs. Follow these steps to adjust the dimming range:

1. Enceneu l'interruptor i moveu el regulador lliscant a la configuració més baixa (la més a l'esquerra).
2. Rotate (counter-clockwise) the sensitivity dial (located on the side of the switch) all the way up. NOTA: If the dial stops in either direction, do not force it.
3. Rotate (clockwise) the sensitivity dial down slowly until the preferred lowest light level is achieved and the lights are not flickering.

Figure 4: Location of the sensitivity dial for dimming range adjustment.

5. Funcionament

• On/Off: Press the top or bottom of the rocker switch to turn the lights on or off.
• Dimecres: Use the horizontal slider to adjust the light intensity. Move the slider up for brighter light and down for dimmer light.
• Funció de memòria: The switch remembers the last dimmed light setting and will turn on to that exact light level when activated.

6. Compatibilitat

This dimmer switch is universally compatible with most dimmable LED, CFL, incandescent, and halogen bulbs.

• LED/CFL regulable: Up to 150 Watts (minimum load: 3W)
• Incandescent/Halògens: Fins a 600 watts

Figure 5: Bulb compatibility and wattage qualificacions.

7. Dimensions del producte

Figure 6: Product dimensions. The switch measures approximately 4.13 x 2.12 x 1.35 inches. Ensure your electrical box has a depth of at least 2 inches for proper fit.

8. Especificacions

9. Solució De Problemes

• Llums intermitents: If your lights are flickering, rotate the side adjustment wheel (sensitivity dial) as described in Section 4.3 to fine-tune the dimming range. Dimmable LEDs may not dim the same as incandescent or halogen bulbs, and their dimming range can vary by manufacturer.
• Lights Not Turning On/Off Consistently (3-Way): In 3-way applications, ensure the line and load wires are correctly identified and connected. Incorrect wiring can cause inconsistent operation or flickering. Only one dimmer switch should be installed in a 3-way circuit.
• Switch Does Not Fit in Electrical Box: The dimmer switch has dimensions of 4.13 x 2.12 x 1.35 inches. Ensure your electrical box has a depth of at least 2 inches to accommodate the switch.

10. Manteniment

To clean the dimmer switch and wall plate, wipe with a soft, damp drap. No utilitzeu productes de neteja abrasius ni dissolvents. Assegureu-vos que l'alimentació estigui apagada abans de netejar.

11. Garantia i Suport

Per obtenir informació sobre la garantia o assistència tècnica, consulteu el lloc web oficial del fabricant. website or contact their customer service. Keep your purchase receipt for proof of purchase.