1. Introducció
Thank you for choosing the pTron Mount ST4F Adjustable Car Mount Phone Holder. This manual provides detailed instructions for the safe and effective use of your new car mount. Please read this manual thoroughly before installation and operation, and retain it for future reference.
2. Informació de seguretat
- Ensure the mount is securely installed before placing a device in it. A loose mount can obstruct your view or become a projectile in an accident.
- Do not install the mount in a location that obstructs your driving view or interferes with airbags.
- Evita ajustar el suport o el dispositiu mentre condueixes. Atura't sempre en un lloc segur si cal ajustar-ho.
- Keep the mount away from extreme temperatures, direct sunlight for prolonged periods, and moisture to prevent damage to the product and your device.
- This product is designed for holding smartphones and small tablets within the specified size range. Do not use it for other purposes.
3. Contingut del paquet
Si us plau, verifiqueu que tots els elements siguin presents al vostre paquet:
- Mobile Holder (Clamp)
- Base (with Suction Cup and Telescopic Arm)
4. Configuració i instal·lació
The pTron Mount ST4F can be installed on your car's dashboard or windshield.
4.1. Triar una ubicació d'instal·lació
Select a flat, clean surface on your dashboard or windshield that does not obstruct your view of the road or interfere with vehicle controls and safety features like airbags.
4.2. Attaching the Suction Base
- Clean the chosen surface thoroughly to ensure optimal suction.
- Traieu la pel·lícula protectora de la ventosa.
- Col·loqueu la ventosa fermament contra la superfície desitjada.
- Premeu cap avall 1-button lock lever located on the base to create a strong vacuum seal. Ensure the base is securely attached and does not wobble.
Image 4.2.1: Suction base with locking mechanism.
4.3. Attaching the Mobile Holder
- Loosen the collar nut on the ball joint of the telescopic arm.
- Align the mobile holder (clamp) with the ball joint and push it onto the ball until it is seated properly.
- Tighten the collar nut to secure the mobile holder in place. Do not overtighten.
Image 4.3.1: Fully assembled pTron Mount ST4F.
5. Instruccions de funcionament
5.1. Inserting Your Device
- Gently pull apart the two side arms of the mobile holder. The holder is designed to accommodate devices with a screen size range of 50mm-95mm (width).
- Place your smartphone or small tablet into the holder, ensuring it is centered and held securely by the cushion-based side arms.
- Release the side arms slowly to allow them to grip your device firmly. The cushion padding protects your device from scratches.
Image 5.1.1: Smartphone secured in the holder.
5.2. Ajust Viewing Angle and Position
- Rotació de 360°: The mobile holder can be rotated 360 degrees to switch between portrait and landscape viewing modes. Loosen the collar nut slightly, adjust the angle, and then re-tighten.
- Telescopic Arm: The telescopic arm can be extended by approximately 2 inches to bring your device closer for better viewing. Loosen the locking knob on the arm, extend or retract, and then re-tighten the knob.
- Ajust d'inclinació: The ball joint allows for tilting the device up, down, left, or right. Loosen the collar nut, adjust the tilt, and then re-tighten.
Image 5.2.1: Demonstrating the adjustable arm and rotation.
6. Manteniment
6.1. Cleaning the Suction Base
If the suction base loses its grip, it can often be restored to its prime condition:
- Carefully detach the mount from the surface.
- Rinse the suction cup with warm water.
- Allow it to air dry completely. Do not use cloths or paper towels, as they can leave lint.
- Once dry, the suction power should be restored.
6.2. Neteja general
Netegeu la muntura amb un drap suauamp cloth. Do not use harsh chemicals or abrasive cleaners, as these can damage the material.
7. Solució De Problemes
| Problema | Causa possible | Solució |
|---|---|---|
| Mount does not stick securely to the surface. | Surface is dirty or oily; suction cup is dirty or damaged; locking lever not fully engaged. | Clean the surface and the suction cup (see Section 6.1). Ensure the locking lever is fully pressed down. Try a different, smoother surface. |
| Phone wobbles or falls out of the holder. | Side arms not gripping firmly; device is too large/small for the holder; holder not tightened on ball joint. | Ensure the side arms are fully closed around the device. Verify your device's width is within 50mm-95mm. Tighten the collar nut on the ball joint. |
| Telescopic arm or rotation joint is loose. | Locking knob/collar nut is not tightened. | Tighten the respective locking knob for the telescopic arm or the collar nut for the rotation joint. |
8. Especificacions
| Característica | Detall |
|---|---|
| Marca | pTron |
| Nom del model | Mount ST4F |
| Color | Negre |
| Dispositius compatibles | Smartphones (All iOS & Android Devices) |
| Amplada del telèfon compatible | 50 mm - 95 mm |
| Tipus de muntatge | Tauler de control, parabrisa |
| Característiques del producte | Adjustable, Hands-Free, Rotatable (360°), Telescopic Arm, Strong Suction Base |
| Material | Acrilonitril butadiè estirè (ABS) |
| Dimensions de l'article (L x A x A) | 11.5 x 10 x 9 centímetres |
| Pes de l'article | 147 grams |
9. Informació de la garantia
The pTron Mount ST4F comes with a 6 mesos de garantia del fabricant des de la data de compra. Aquesta garantia cobreix els defectes de fabricació. Si us plau, conserveu el rebut de compra com a comprovant de compra per a reclamacions de garantia. La garantia no cobreix els danys causats per un mal ús, accidents, modificacions no autoritzades o desgast normal.
10. Suport i informació de contacte
For any support, queries, or warranty claims, please contact:
Importer Contact Information:
Palred Electronics Pvt. Ltd.,
Plot no. 2, 8-2-703/2/B, Road no. 12,
Banjara Hills, Hyderabad – 500034,
Telangana, Índia
Informació de contacte del fabricant:
Building A1, Red Box Creative Park,
No. 3 Huancheng South Road, Bantian Street,
Longgang District, Shenzhen City, China 518116.
Parude Technology (Shenzhen) Co. Ltd.