Introducció
The Behringer CLOCKED SEQUENTIAL CONTROL MODULE 1027 is a faithful reproduction of the legendary 2500 Series 8-position step sequencer. Designed for Eurorack systems, this module provides precise control over voltage and gate signals, making it an essential tool for creating complex melodic and rhythmic patterns in your modular synthesizer setup. Its robust design and intuitive interface ensure reliable performance and creative flexibility.
Instruccions importants de seguretat
- Read these instructions thoroughly before operating the module.
- Conserveu aquestes instruccions per a referència futura.
- Tingueu en compte totes les advertències del producte i del manual.
- Seguiu totes les instruccions per a un funcionament segur.
- No utilitzeu aquest aparell a prop d'aigua o humitat.
- Netegeu només amb un drap sec.
- No obstruïu cap obertura de ventilació. Instal·leu d'acord amb les instruccions del fabricant.
- No instal·leu a prop de cap font de calor com ara radiadors, registres de calor, estufes o altres aparells (inclosos amplificadors) que produeixen calor.
- Utilitzeu només accessoris/accessoris especificats pel fabricant.
- Demaneu tot el servei a personal de servei qualificat. Cal fer servei quan l'aparell s'hagi fet malbé d'alguna manera.
Configuració
Instal·lació d'Eurorack
The CLOCKED SEQUENTIAL CONTROL MODULE 1027 is designed for installation into a standard Eurorack case. Ensure your Eurorack case has sufficient power and space (16 HP width) before installation.
- Apagar: Always disconnect power from your Eurorack case before installing or removing any modules.
- Muntatge: Align the module with an available 16 HP space in your Eurorack case. Secure it using the provided screws.
- Connexió d'alimentació: Connect the 16-pin power cable from your Eurorack power supply to the module's power header. Ensure the red stripe on the cable aligns with the -12V pin on both the module and the power supply. Incorrect connection can damage the module and/or power supply.
- Encès: Un cop muntat i connectat correctament, podeu engegar la caixa Eurorack.
Figura 1: Frontal view of the Behringer 1027 module, showing all controls and patch points. This image illustrates the module's layout for proper installation and connection within a Eurorack system.
Connexions inicials
To begin using the 1027, connect its outputs to other modules in your Eurorack system. Common connections include:
- Clock Input (CLK IN): Connect a clock signal from another module (e.g., an LFO or clock divider) to the CLK IN jack to drive the sequencer.
- CV Outputs (CH A, CH B, CH C): Patch these outputs to the CV inputs of oscillators, filters, or other modules to control pitch, cutoff, or other parameters.
- Gate Outputs (POSITION GATES 1-8): Connect these to gate inputs of envelope generators or drum modules to trigger events at specific steps.
Figura 2: Primer pla view of the input and output jacks on the Behringer 1027 module, highlighting the various patch points for integration into a modular system.
Instruccions de funcionament
Acabatview de Controls
The 1027 module features a clear layout of controls for intuitive sequencing:
- Botó de VELOCITAT: Adjusts the speed of the internal clock. The range switch (LOW/HIGH) selects the clock speed range.
- PULSE WIDTH Knob: Controls the width of the gate pulses. The switch (INT/EXT) selects between internal control or external CV control.
- Interruptor ON / OFF: Toggles the sequencer's operation.
- STEP Buttons (1-8): Each step has a corresponding button to activate/deactivate it.
- CV Knobs (A, B, C for each step): Adjust the control voltage output for each of the three channels (A, B, C) at each step.
- POSITION GATES (1-8): Individual gate outputs for each step.
- STEP/RESET Buttons: Manual step advance and reset functions.
Figura 3: Angle view of the Behringer 1027 module, providing a clear perspective of the control knobs and buttons for each step and channel.
Creating a Sequence
- Estableix el rellotge: Utilitza el TARIFA pom i BAIX/ALT switch to set the desired tempo. Alternatively, connect an external clock to the CLK IN jack.
- Activate Steps: Premeu el botó PAS buttons (1-8) to activate the desired number of steps in your sequence. Active steps will typically illuminate.
- Adjust CV: For each active step, turn the CV Knobs (A, B, C) per establir el voltage level for each channel. These voltages will be outputted sequentially.
- Configure Gates: El POSICIONAR PORTES will output a pulse when their corresponding step is active. Use these to trigger envelopes or other events.
- Inici/Parada: Utilitza el ON/OFF switch to start and stop the sequence.
Funcions avançades
- External Pulse Width Control: Connect a CV source to the EXT input for the PULSE WIDTH section to dynamically control the gate pulse width.
- Manual Step/Reset: El PAS i RESET buttons allow for manual control over the sequence progression, useful for live performance or precise programming.
Manteniment
Neteja
To maintain the appearance and functionality of your module:
- Always power off your Eurorack system before cleaning.
- Use a soft, dry, lint-free cloth to wipe the module's surface.
- Per a la brutícia persistent, lleugerament dampRenta el drap amb aigua. Evita utilitzar productes químics agressius o netejadors abrasius.
- Do not allow any liquids to enter the module through jacks or openings.
Emmagatzematge
When not in use for extended periods, store the module in a cool, dry place, away from direct sunlight and extreme temperatures. If removed from the Eurorack case, store it in anti-static packaging.
Resolució de problemes
| Problema | Causa possible | Solució |
|---|---|---|
| Module does not power on. | Incorrect power cable connection; Eurorack power supply off or faulty. | Check power cable orientation (red stripe to -12V). Ensure Eurorack power supply is on and functioning correctly. |
| Sequencer not advancing steps. | No clock signal; ON/OFF switch is OFF; RATE knob set too low. | Connect a clock signal to CLK IN. Ensure ON/OFF switch is ON. Increase the RATE knob setting. |
| No CV output from a channel. | CV knob for that step/channel is at minimum; step is not active. | Adjust the corresponding CV knob. Ensure the step is active (illuminated). |
| No Gate output from a position. | Step is not active; PULSE WIDTH set to minimum. | Ensure the step is active. Increase the PULSE WIDTH setting. |
Especificacions
| Característica | Detall |
|---|---|
| Nom del model | 1027 |
| Tipus de mòdul | Mòdul de control seqüencial cronometrat |
| Sèrie | Sèrie 2500 |
| Format | Eurorack |
| Amplada | 16 CV |
| profunditat | Not specified (typical Eurorack depth) |
| Consum d'energia | Not specified (standard Eurorack +12V, -12V) |
| Entrades | Clock In, External Pulse Width CV |
| Sortides | 3 x CV (A, B, C), 8 x Gate (Position Gates) |
| Dimensions (A x A x P) | 43 x 162 x 129 mm (aprox. 1.69 x 6.38 x 5.08 polzades) |
| Pes de l'article | 0.77 lliures (aprox. 0.35 kg) |
| Tecnologia de connectivitat | Jack TS de 3.5 mm |
| Font d'alimentació | DC power supply (via Eurorack bus) |
Garantia
Behringer products are covered by a limited warranty. For detailed information regarding warranty terms, conditions, and registration, please visit the official Behringer website or the Music Tribe Community portal. Warranty services are typically handled through authorized service centers.
Descripció de la garantia: Community. Musictribe. Com.
Suport
For further assistance, technical support, or to download the latest firmware and documentation, please visit the official Behringer weblloc:
- Oficial de Behringer Weblloc
- Music Tribe Community (for warranty and support information)
You can also contact your local Behringer dealer or distributor for product-specific inquiries.