1. Introducció
This manual provides essential information for the safe and efficient operation of your LEESKY 2000W Pure Sine Wave Power Inverter. Please read these instructions thoroughly before installation and use. Retain this manual for future reference.
Contingut del paquet:
- 1x LEESKY 2000 Watt Pure Sine Wave Power Inverter
- 2x Battery Cables (black and red)
- 1x 15ft Remote Controller
- 1x Earth Wire
- 8x Shockproof Pads
- 1x Manual d'usuari (aquest document)
Image 1.1: The LEESKY 2000W Pure Sine Wave Power Inverter with its included battery cables, remote controller, and GFCI outlet.
2. Informació de seguretat
Observe the following safety precautions to prevent injury or damage to the inverter and connected devices:
- NO exceed the inverter's rated power of 2000 Watts. Overloading can cause damage to the inverter and connected appliances.
- NO leave the power inverter in the ON position while your vehicle's engine is off to prevent battery drain.
- Always disconnect the positive battery terminal before performing any wiring or maintenance on the inverter.
- Install the inverter in a cool, dry environment, away from direct sunlight, moisture, and flammable materials.
- Ensure proper ventilation around the inverter to prevent overheating. Do not block cooling fan vents.
- This inverter is designed for 12V DC input. Connecting to other voltage sources may cause severe damage.
3. Configuració i instal·lació
3.1 Connecting to a Battery
- Assegureu-vos que l'interruptor d'alimentació de l'inversor estigui en la posició OFF.
- Connect the red battery cable to the positive (+) terminal of your 12V battery.
- Connect the other end of the red battery cable to the positive (+) input terminal on the inverter.
- Connect the black battery cable to the negative (-) terminal of your 12V battery.
- Connect the other end of the black battery cable to the negative (-) input terminal on the inverter.
- Assegureu-vos que totes les connexions estiguin estretes i segures.
- Connect the included earth wire to the ground terminal on the inverter and to a suitable ground point.
Nota: For optimal performance and safety, use a 12V battery with a capacity of 400 Ah or above. Always use the provided cables or cables of equivalent gauge suitable for 2000W applications.
3.2 Remote Controller Installation
The remote controller allows for convenient monitoring and control of the inverter from a distance.
- Locate the RJ10 port on the inverter.
- Connect one end of the 15ft remote controller cable to the RJ10 port on the inverter.
- Connect the other end of the cable to the remote controller unit.
The inverter can also be turned on/off using the power switch directly on the unit if the remote controller is not connected or desired.
Imatge 3.1: acabatview of inverter components including positive/negative terminals, GFCI outlets, USB ports, LCD display, and remote controller port.
4. Funcionament
4.1 Encendre l'inversor
- After ensuring all connections are secure, switch the inverter's power button to the ON position.
- The LCD display on the inverter (or remote controller) will illuminate, showing input voltage, potència de sortidatage, and battery status.
4.2 Connecting AC Devices
The LEESKY 2000W inverter provides clean, stable pure sine wave electricity, suitable for sensitive electronics.
- Plug your AC devices into the two 110-120V AC GFCI outlets.
- For charging USB devices, use the two 2.4A USB ports.
- Assegureu-vos el wat totaltagLa potència de tots els dispositius connectats no supera els 2000 W.
Image 4.1: The inverter's LCD display provides real-time information, and the GFCI outlets offer enhanced safety.
4.3 LCD Display and Remote Control
The LCD display provides critical operational data:
- Entrada Voltage: Mostra el volum actual de CCtage de la bateria.
- Potència de sortidatage: Shows the real-time power consumption of connected AC devices.
- Estat de la bateria: Indica el nivell de càrrega de la bateria.
- Codi de protecció: Displays error codes if a protection mechanism is triggered.
- Temperatura: Shows the internal temperature of the inverter.
The remote controller mirrors this information and allows for convenient power control. It also features a backlight switch for visibility in various lighting conditions.
Image 4.2: The remote control provides comprehensive monitoring and control, displaying input voltage, potència de sortidatage, battery status, and protection warnings.
5. Protection Features and Troubleshooting
The LEESKY 2000W inverter incorporates multiple protection mechanisms to ensure safe operation and prevent damage to the unit and connected devices. The LCD display will show warning symbols and protection codes when an issue occurs.
5.1 Built-in Protections:
- Protecció de sobrecàrrega: Activates when output power exceeds 2000W-2200W. The inverter will shut down to prevent damage.
- Protecció de sobretemperatura: Engages if the internal temperature reaches approximately 149℉ (65℃). The intelligent cooling fan runs automatically when the temperature reaches 104℉ (40℃) or load power exceeds 40% of rated power.
- Low-input Voltage Protecció: Triggers an alarm at 9.8V±0.5VDC and shuts down at 9.5V±0.5VDC to protect the battery from over-discharge.
- High-input Voltage Protecció: Shuts down the inverter if input voltage exceeds 16V±0.5VDC.
- Protecció contra curtcircuits: Automatically protects against output short circuits.
- Protecció de polaritat inversa: Evita danys causats per connexions incorrectes dels terminals de la bateria.
- Input/Output Isolated Design: Enhances safety by electrically separating input and output circuits.
Image 5.1: The inverter's multi-protection system safeguards against common electrical faults.
5.2 Troubleshooting Common Issues:
| Problema | Causa possible | Solució |
|---|---|---|
| L'inversor no s'encén. | Connexions de bateria fluixes, baix volum de bateriatage, inverter switch off. | Check battery connections, charge battery, ensure inverter switch is ON. |
| Sense sortida de CA. | Overload, short circuit, high/low input voltage, GFCI tripped. | Reduir la càrrega, comprovar si hi ha curtcircuits, verificar el vol de la bateriatage, reset GFCI. |
| Inverter shuts down. | Overload, overheating, low/high input voltage. | Reduce load, allow inverter to cool, check battery voltage. |
| El ventilador funciona constantment o sorollosament. | High internal temperature, heavy load. | Ensure adequate ventilation, reduce load. This is normal operation under certain conditions. |
6. Manteniment
Regular maintenance ensures the longevity and reliable performance of your LEESKY inverter.
- Neteja: Netegeu periòdicament l'exterior de l'inversor amb un drap sec i suau. No utilitzeu netejadors líquids ni dissolvents.
- Ventilació: Ensure the cooling vents are free from dust and debris. Blocked vents can lead to overheating.
- Connexions: Regularly check all battery and output connections to ensure they are tight and free from corrosion.
- Emmagatzematge: Si guardeu l'inversor durant un període prolongat, desconnecteu-lo de la bateria i guardeu-lo en un lloc fresc i sec.
7. Especificacions
| Característica | Especificació |
|---|---|
| Model | LEESKY 2000W Pure Sine Wave Inverter |
| Potència nominal | 2000 W (continu) |
| Forma d'ona de sortida | Onda senyal pura |
| Distorsió harmònica total (THD) | < 3% |
| Entrada Voltage | 12V DC |
| Vol. De sortidatage | 110-120 VAC ± 10% |
| Freqüència de sortida | 60 Hz |
| Corrent inactiu | Aproximadament 1.7 Amps |
| Eficiència | Fins al 90% |
| Punts de venda | 2x GFCI Sockets |
| Ports USB | 2x 2.4A USB |
| Longitud del cable del comandament a distància | 15 peus |
| Protecció de sobrecàrrega | 2000W ~ 2200W |
| Protecció contra la temperatura | Around 149°F (65°C) |
| Temperatura de treball | -22 ° F ~ 140 ° F (-30 ° C ~ 60 ° C) |
| Sobrevoltage Tancament | 16V ± 0.5VDC |
| Baix voltage Alarma | 9.8V ± 0.5VDC |
| Baix voltage Tancament | 9.5V ± 0.5VDC |
| Dimensions del producte | 19.85 x 9.4 x 3.8 polzades |
| Pes de l'article | 13.46 lliures |
Image 7.1: Physical dimensions and weight of the inverter, along with battery cable specifications.
8. Garantia i Suport
8.1 Informació de la garantia
The LEESKY 2000W Pure Sine Wave Power Inverter comes with an 18-month maintenance period from the date of purchase. This warranty covers manufacturing defects and ensures product reliability. Please retain your proof of purchase for warranty claims.
8.2 Atenció al client
For technical assistance, troubleshooting, or warranty inquiries, please contact LEESKY customer support through the retailer where the product was purchased or refer to the official LEESKY weblloc per obtenir dades de contacte.
An additional user guide in PDF format is available for download: Descarrega la Guia de l'usuari (PDF)
