Itho Daalderop Close-In Electric Water Heater 10l with Copper Tub

Introducció

This manual provides essential information for the safe and efficient installation, operation, and maintenance of your Itho Daalderop Close-In Electric Water Heater. Please read this manual thoroughly before installation and retain it for future reference.

Figura 1: Frontal view of the Itho Daalderop Close-In Electric Water Heater. This compact unit features a white casing, a control dial on the upper right, and water inlet/outlet connections on top.

Informació de seguretat

Seguiu sempre les següents precaucions de seguretat per evitar lesions o danys a l'aparell:

• Installation must be performed by a qualified professional in accordance with local regulations and standards.
• Ensure the power supply matches the specifications of the water heater (2.3E+2 Volts AC).
• No feu funcionar l'escalfador d'aigua si està danyat o no funciona correctament.
• Desconnecteu l'alimentació abans de realitzar qualsevol manteniment o reparació.
• Mantingueu els nens i les mascotes lluny de l'aparell durant el funcionament.
• No bloquejar les obertures de ventilació.

Contingut del paquet

Verifiqueu que tots els components siguin presents i no estiguin danyats en desembalar-los:

• Itho Daalderop Close-In Electric Water Heater (10L capacity)
• Mounting bracket (if applicable, typically pre-attached or included)
• Manual d'instruccions (aquest document)
• Pressure relief valve (may be pre-installed or separate)

Configuració i instal·lació

The Itho Daalderop Close-In water heater is designed for indoor installation, typically under a sink or in a cupboard. It is a wall-mounted unit.

1. Selecció de l'emplaçament

• Choose a location close to the point of use to minimize heat loss.
• Ensure the wall can support the weight of the heater when full (approx. 10 kg + 10 litres = 20 kg).
• Provide adequate clearance for ventilation and maintenance access.
• The unit must be installed in an area not subject to freezing temperatures.

2. Muntatge de la unitat

1. Mark the drilling points for the mounting bracket on the wall.
2. Perfora forats i insereix els tacs de paret adequats.
3. Fixeu fermament el suport de muntatge a la paret.
4. Carefully lift the water heater and hang it onto the mounting bracket. Ensure it is level and securely seated.

3. Connexions de fontaneria

• Connect the cold water supply to the inlet pipe (usually marked blue or with a 'C').
• Connect the hot water outlet to the fixture (usually marked red or with an 'H').
• Install a pressure relief valve on the cold water inlet, if not already integrated. Ensure proper drainage for the relief valve.
• Open the hot water tap at the fixture to allow air to escape while the tank fills.
• Once water flows steadily from the hot tap, close the tap. Check all connections for leaks.

4. Connexió elèctrica

• Assegureu-vos que l'alimentació principal estigui DESCONNECTADA a l'interruptor.
• Connect the water heater to a dedicated electrical circuit as per local electrical codes. The unit operates at 2.3E+2 Volts (AC).
• Verify all wiring connections are secure and correctly insulated.
• Tanqueu el panell d'accés elèctric.

Instruccions de funcionament

1. Posada en marxa inicial

1. Ensure the tank is completely filled with water (as per plumbing connection step).
2. Turn on the main power supply to the water heater at the circuit breaker.
3. The heater will begin to heat the water to the set temperature. This may take some time depending on the initial water temperature and the set point.

2. Ajust de temperatura

The water heater features a temperature control dial on the front panel. Rotate the dial to adjust the desired water temperature. The dial typically ranges from minimum to maximum settings. For energy efficiency and safety, it is recommended to set the temperature between 60°C and 65°C to prevent bacterial growth and scalding.

3. Funcionament normal

The water heater will automatically maintain the set temperature. When hot water is drawn, cold water enters the tank, and the heating element activates to reheat the new water.

Manteniment

Regular maintenance ensures optimal performance and extends the lifespan of your water heater. Always disconnect power before maintenance.

1. Annual Inspection

• Inspect the pressure relief valve: Manually open the valve briefly to ensure it is not seized and water flows freely.
• Check for leaks: Visually inspect all plumbing connections for any signs of water leakage.
• Examine electrical connections: Ensure all wiring is secure and free from corrosion.

2. Descaling (Every 1-3 Years, depending on water hardness)

Mineral deposits (limescale) can build up inside the tank and on the heating element, reducing efficiency. Consult a qualified technician for descaling procedures, especially for units with copper tubs.

Resolució de problemes

Especificacions

• Marca: Itho Daalderop
• Model: Close-In
• Número de peça: SZID-07.02.27.631
• Capacitat: 10 litres
• Voltage: 2.3E+2 volts (CA)
• Estil: Instal·lació interior
• Tipus de muntatge: Mur
• Element de calefacció: Elèctric
• Material de la banyera: coure

Garantia i Suport

For warranty information, technical support, or service requests, please refer to the warranty card included with your product or visit the official Itho Daalderop website. It is recommended to have your model number (Close-In) and part number (SZID-07.02.27.631) ready when contacting support.