ChiliTec 23522 LED and Halogen Foot Dimmer Switch Instruction Manual

1. Introducció

The ChiliTec 23522 foot dimmer switch is designed for stepless brightness control of compatible lighting fixtures. This versatile device supports dimmable LED lamps ranging from 3-100W and traditional incandescent or halogen lamps from 75-300W. It features a robust, non-slip plastic housing and is intended for indoor use only. The dimmer offers two distinct outputs: one for dimmable lighting (0-100% adjustable) and a separate ON/OFF switch for non-dimmable applications, such as reading lamps.

2. Instruccions de seguretat

Llegiu atentament aquestes instruccions de seguretat abans de la instal·lació i l'ús. Si no seguiu aquestes instruccions, podeu patir descàrregues elèctriques, incendis o altres perills.

• Només per a ús interior: This device is rated IP20 and is suitable for dry indoor environments only. Do not expose to moisture or water.
• Seguretat elèctrica: Installation must be performed by a qualified electrician or a person with appropriate electrical knowledge, in accordance with local wiring regulations.
• Desconnexió d'alimentació: Always disconnect the power supply before performing any installation, wiring, or maintenance.
• Compatibilitat de càrrega: Ensure that the connected lampestan dins de l'aigua especificadatage range (3-100W for dimmable LEDs, 75-300W for incandescent/halogen) and are explicitly marked as dimmable.
• Cablejat correcte: Pay close attention to correct polarity (Live, Neutral) and ensure the Protective Earth (PE) conductor is properly connected for Class 1 luminaires.
• Fusible: The device contains an internal, replaceable 2A/250V fuse. Only replace with a fuse of the same type and rating.
• Danys: No utilitzeu el dispositiu si sembla malmès.

3. Contingut del paquet

• 1x ChiliTec 23522 Foot Dimmer Switch

4. Especificacions

5. Configuració i instal·lació

Before proceeding with installation, ensure the main power supply is disconnected at the circuit breaker.

1. Obre l'habitatge: Carefully open the dimmer housing. This typically involves unscrewing the housing screws located on the underside.
2. Interna View:
   

   Interna view of the ChiliTec 23522 foot dimmer switch with the top cover removed. The image displays the green 6-pole screw terminal block for wiring connections, the dimmer circuit board, and the internal components including the fuse and inductor.
3. Diagrama de cablejat: Refer to the wiring diagram below for correct connections.
   

   Wiring diagram for the ChiliTec 23522 foot dimmer switch. This schematic illustrates the connections for two outputs: one dimmable (L/N/PE) and one switched (L/N), along with the input power (L/N/PE) and internal components like the slider, switch, and fuse.

4. Connecteu l'alimentació d'entrada: Connect the main power supply cable (230V/50Hz) to the designated input terminals (L/N/PE) on the 6-pole terminal strip. Ensure Live (L), Neutral (N), and Protective Earth (PE) are correctly matched. The Protective Earth connection is essential for Class 1 luminaires.
5. Connect Output 1 (Dimmable): Connect the cable for your dimmable lamp to the first output terminals (L/N/PE). This output is controlled by the slider for dimming.
6. Connect Output 2 (Switched): Connect the cable for your non-dimmable lamp (e.g., a reading lamp) to the second output terminals (L/N). This output is controlled by the separate ON/OFF button.
7. Cables segurs: Ensure all wires are securely fastened in the screw terminals. The minimum wire cross-section is 3x 1.0 mm², and the outer diameter of the connecting cables should not exceed 6.5mm.
8. Install Strain Relief: Properly install the strain relief mechanisms for all connected cables to prevent accidental pulling or damage to the connections.
9. Tancament d'habitatges: Carefully close the dimmer housing and secure it with the screws.
10. Restaura l'alimentació: Un cop finalitzada i verificada la instal·lació, restableix l'alimentació del circuit.

6. Instruccions de funcionament

The ChiliTec 23522 foot dimmer switch offers intuitive control over your lighting.

ChiliTec 23522 foot dimmer switch, top-down view.

ChiliTec 23522 foot dimmer switch, angled top view.

• Dimmable Output Control: Use the prominent slider control to adjust the brightness of the connected dimmable lamp. Sliding it from one end to the other will smoothly vary the light output from 0% (off) to 100% (full brightness).
• Switched Output Control: The separate square button acts as an ON/OFF switch for the second, non-dimmable output. Press the button to toggle the connected lamp encès o apagat.
• Orientation Light: The dimmer features an orientation light, which may illuminate to help locate the switch in the dark.

7. Manteniment

• Neteja: To clean the dimmer, wipe the exterior with a dry, soft cloth. Do not use abrasive cleaners, solvents, or wet cloths, as this may damage the device or pose an electrical hazard.
• Substitució de fusibles: The dimmer contains an internal 2A/250V fuse. If the dimmer stops functioning, the fuse may need replacement. Disconnect power before opening the housing and replace the fuse with one of identical type and rating (2A/250V).
• Inspecció: Periodically inspect the cables and housing for any signs of wear or damage. If damage is found, discontinue use and have the device inspected by a qualified professional.

8. Solució De Problemes

If you encounter issues with your ChiliTec 23522 dimmer, refer to the following common troubleshooting steps:

• La llum no s'encén:
  • Comproveu si la font d'alimentació principal està connectada i activa.
  • Verifiqueu que totes les connexions de cablejat siguin segures i correctes segons el diagrama.
  • Ensure the connected lamp is functional and properly installed.
  • Check the internal 2A/250V fuse and replace if blown (see Maintenance section).
• Light Not Dimming or Flickering:
  • Confirm that the connected lamp is explicitly marked as dimmable. Not all LED lamps són regulables.
  • Assegureu-vos que lampés watage is within the specified range for the dimmer (3-100W for LEDs, 75-300W for incandescent/halogen).
  • Comproveu si hi ha connexions de cablejat soltes.
  • Si utilitzeu LED lamps, some LED types may exhibit minor flickering at very low dimming levels due to compatibility.
• No Power to Switched Output:
  • Ensure the ON/OFF button is pressed to the 'ON' position.
  • Verify wiring connections for the second output.

Si el problema persisteix després d'intentar aquests passos, poseu-vos en contacte amb l'atenció al client.

9. Informació de la garantia

This ChiliTec product is covered by a standard manufacturer's warranty. The specific terms and duration of the warranty may vary based on your region and point of purchase. Please retain your proof of purchase for any warranty claims. For detailed information regarding your warranty, refer to the documentation provided at the time of purchase or contact your retailer.

10. Suport

Should you require technical assistance, have questions about installation, or need further support regarding your ChiliTec 23522 foot dimmer switch, please contact:

• ChiliTec Customer Service: Refer to the contact information provided on the product packaging or the official ChiliTec weblloc.
• El vostre distribuïdor: The store or online platform where you purchased the product can often provide direct support or guide you to the appropriate service channels.