Fms MXS V2 1100mm 3D Aerobatic RC Airplane Instruction Manual

1. Introducció

Welcome to the world of Fms RC aerobatic flight! The Fms MXS V2 1100mm is a high-performance 3D aerobatic remote control airplane designed for enthusiasts seeking advanced maneuverability and a thrilling flying experience. This Plug and Play (PNP) model comes equipped with a powerful motor, ESC, and digital metal gear servos, requiring only your preferred radio system, battery, and charger to get airborne.

Its robust EPO foam construction, combined with enhanced features like wing tip Side Force Generators and extended horizontal stabilizers, ensures both durability and exceptional flight characteristics. Please read this manual thoroughly before assembly and operation to ensure safe and optimal performance.

2. Informació de seguretat

ADVERTIMENT: Failure to operate this product in a safe manner may result in damage, injury, or property damage. Always operate within your skill level and follow all instructions.

• Always operate in open areas away from people, vehicles, and buildings.
• Keep hands clear of the propeller when the battery is connected.
• Ensure all control surfaces move freely and correctly before each flight.
• Do not fly near power lines, airports, or restricted airspace.
• Always disconnect the battery after use and before performing any maintenance.
• Es recomana la supervisió d'un adult per als operadors més joves.

3. Contingut del paquet

The Fms MXS V2 1100mm PNP package includes the following components:

• Pre-assembled airframe (wings, fuselage, tail sections)
• 35-41 1230kv Outrunner motor (pre-installed)
• 40A ESC (pre-installed)
• 4 digital full metal gear servos (pre-installed)
• Hèlix
• Tren d'aterratge
• Wing tip Vortex generators
• Small parts and hardware for final assembly
• Manual d'instruccions

Note: A radio transmitter, receiver, flight battery, and charger are NOT included with this PNP version.

Figura 1: Explotat view diagram of the Fms MXS V2 1100mm RC airplane components.

4. Instruccions de muntatge

The Fms MXS V2 is designed for effortless assembly. Follow these steps to prepare your aircraft for flight. Only glue is required for the wing tip Vortex generators.

4.1 Wing Assembly

Figure 2: Visual guide for key assembly steps, including wing and tail section attachment.

1. Carefully attach the main wings to the fuselage. Ensure all connections are secure.
2. Connect the aileron servo leads from the wings to the corresponding channels on your receiver.
3. Secure the wings using the provided screws or locking mechanisms.

4.2 Tail Section and Vortex Generators

1. Attach the horizontal and vertical stabilizers to the rear of the fuselage. Connect the elevator and rudder servo leads.
2. Apply a small amount of foam-safe glue to secure the wing tip Vortex generators in place. Allow sufficient drying time.

4.3 Landing Gear Installation

1. Install the main landing gear and tail wheel assembly. Ensure they are firmly attached and allow for smooth movement.

Figure 3: The Fms MXS V2 1100mm with its robust landing gear installed, ready for ground operations.

5. Configuració

As a Plug and Play (PNP) model, the Fms MXS V2 requires you to supply your own radio system (transmitter and receiver), flight battery, and charger.

5.1 Instal·lació i vinculació del receptor

1. Install your chosen receiver into the designated compartment within the fuselage.
2. Connect the pre-installed servo leads (aileron, elevator, rudder, throttle) to the corresponding channels on your receiver. Refer to your receiver's manual for correct channel assignments.
3. Bind your receiver to your transmitter according to your radio system's instructions.

5.2 Battery Installation and Center of Gravity (CG)

1. Insert your flight battery (recommended 4S LiPo, 2200-3300mAh) into the battery compartment. Secure it with the provided hook-and-loop straps.
2. Ensure the aircraft's Center of Gravity (CG) is within the recommended range specified in the full instruction manual. Adjust battery position as needed. Proper CG is crucial for stable flight.

Figure 4: The powerful 35-41 1230kv Outrunner motor, part of the pre-installed power system.

6. Instruccions de funcionament

The Fms MXS V2 is a 3D aerobatic aircraft capable of advanced maneuvers. Familiarize yourself with basic flight controls before attempting complex aerobatics.

6.1 Comprovacions prèvies al vol

• Check all control surfaces (ailerons, elevator, rudder) for correct movement and throw.
• Ensure the propeller is securely attached and free from damage.
• Verify battery is fully charged and securely installed.
• Perform a range check of your radio system.

6.2 Enlairament

Place the aircraft on a smooth, flat surface facing into the wind. Gradually increase throttle while applying slight up-elevator to lift off. For hand launches, ensure sufficient throttle and a firm, level throw.

6.3 Flight Controls and Aerobatics

The MXS V2 excels in 3D aerobatics. Its wing tip Side Force Generators and upgraded horizontal stabilizers provide superior control for maneuvers like Knife Edge flying, loops, rolls, and inverted flight.

Figure 5: The Fms MXS V2 1100mm demonstrating its 3D aerobatic capabilities with a vertical climb.

Figure 6: The Fms MXS V2 1100mm maintaining stable inverted flight, showcasing its precise control.

6.4 Aterratge

Approach into the wind, reducing throttle gradually. Maintain sufficient airspeed to avoid a stall. Gently flare the aircraft just above the ground to achieve a smooth touchdown.

6.5 Vídeos instructius

7. Manteniment

• Neteja: After each flight, wipe down the airframe with a soft, dry cloth to remove dirt and debris.
• Comprovació de l'hèlix: Regularly inspect the propeller for cracks, nicks, or damage. Replace if necessary to ensure safe and efficient flight.
• Control Surface Inspection: Check all control surfaces and linkages for any looseness or damage. Ensure servos operate smoothly.
• Cura de la bateria: Store LiPo batteries in a cool, dry place at storage voltage. Do not overcharge or over-discharge.
• Motor i ESC: Ensure the motor spins freely and the ESC connections are secure. Avoid prolonged operation in dusty conditions.

8. Solució De Problemes

9. Especificacions

Figure 7: Dimensional diagram of the Fms MXS V2 1100mm RC airplane.

10. Garantia i Suport

For warranty information, technical support, or replacement parts, please refer to the official Fms website or contact your authorized Fms dealer. Keep your purchase receipt for warranty claims.

Fms is committed to providing high-quality products and customer satisfaction. If you encounter any issues, please reach out to their support team for assistance.