Axxess AXLOC-FD2

Axxess AXLOC-FD2 2-Channel Line Output Converter Instruction Manual for Ford 2011-Up

Model: AXLOC-FD2

Introducció

The Axxess AXLOC-FD2 is a 2-channel line output converter designed to integrate aftermarket amplifiers with factory audio systems in select Ford vehicles from 2011 and newer. This device converts high-level speaker signals from the factory radio into low-level RCA signals, providing a clean and adjustable output for your amplifier. It also provides a 12-volt accessory output for ampencès del lifier.

Informació de seguretat

  • Always disconnect the vehicle's negative battery terminal before beginning any installation.
  • Assegureu-vos que totes les connexions del cablejat estiguin ben fixades i degudament aïllades per evitar curtcircuits.
  • Consulteu un instal·lador professional d'àudio per a cotxes si no teniu cap dubte sobre alguna part del procés d'instal·lació.
  • Do not operate the vehicle's audio system at excessively high volumes for prolonged periods, as this may cause hearing damage.
  • Mount the converter in a location that is protected from moisture and excessive heat.

Contingut del paquet

Verifiqueu que hi hagi tots els elements abans de començar la instal·lació:

  • AXLOC-FD2 Line Output Converter Module
  • Arnès de cablejat específic per a vehicles
  • RCA output cables
  • Remote turn-on wire
Various components of the Axxess AXLOC-FD2 kit, including the main converter module, wiring harnesses, and RCA cables.
Figure 1: Components included in the Axxess AXLOC-FD2 kit. This image displays the main converter unit, various wiring harnesses with connectors, and RCA cables, illustrating the complete set of parts for installation.

Instruccions d'instal·lació

This section outlines the general installation procedure. Specific vehicle disassembly instructions are beyond the scope of this manual. Refer to a vehicle-specific service manual for dash removal and access to the factory radio wiring.

Eines necessàries:

  • Pelafils/enganxadores
  • Cinta elèctrica o tub termoretractable
  • Multímetre
  • Eines d'eliminació de panells
  • Screwdrivers/socket set

Wiring Diagram and Connections:

  1. Desconnecta la bateria: Before starting, disconnect the negative terminal of the vehicle's battery to prevent electrical shorts.
  2. Access Factory Radio: Carefully remove the necessary trim panels and components to gain access to the back of the factory radio.
  3. Identify Speaker Wires: Using a vehicle-specific wiring diagram or a multimeter, identify the factory speaker output wires (positive and negative for each channel) from the factory radio harness.
  4. Connect Input Harness: Connect the vehicle-specific wiring harness provided with the AXLOC-FD2 to the factory radio harness. This harness will typically plug in-line with the factory radio, intercepting the speaker outputs.
  5. Connect AXLOC-FD2 Module: Plug the main connector from the vehicle-specific harness into the AXLOC-FD2 module.
  6. Connect RCA Outputs: Connect the RCA output cables from the AXLOC-FD2 module to the RCA inputs of your aftermarket ampmés viu.
  7. Connect Remote Turn-On: The AXLOC-FD2 provides a 12-volt accessory output (remote turn-on) for your amplifier. Connect this wire to the remote turn-on input of your amplifier. This eliminates the need to find a separate switched 12V source.
  8. Connexió a terra: Ensure the AXLOC-FD2 module has a solid ground connection. The vehicle-specific harness should provide this, but always verify.
  9. Muntatge: Securely mount the AXLOC-FD2 module in a suitable location, away from heat and moisture, ensuring it does not interfere with any moving parts or vehicle components.
Axxess AXLOC-FD2 wiring harness and converter units laid out, showing the main connections.
Figura 2: Mésview of the AXLOC-FD2 wiring harness and converter units. This image illustrates how the main harness connects to the converter module, providing a visual guide for the primary connections during installation.
Detallada view of the Axxess AXLOC-FD2 converter module and various connectors.
Figura 3: Detallada view of the AXLOC-FD2 converter module and associated connectors. This image provides a closer look at the input and output ports on the converter, as well as the design of the various plugs and sockets.

Instruccions de funcionament

Ajust de guany:

The AXLOC-FD2 features adjustable gain controls to match the output level of the factory radio to the input sensitivity of your aftermarket amplifier. Proper gain setting is crucial for optimal sound quality and to prevent distortion.

  1. Configuració inicial: Start with the gain controls on the AXLOC-FD2 set to their minimum position (fully counter-clockwise).
  2. AmpGuany lifier: Set the gain control on your aftermarket amplifier to its minimum position.
  3. Reproduir música: Play a dynamic piece of music through your factory radio at about 75% of its maximum volume.
  4. Adjust AXLOC-FD2 Gain: Slowly increase the gain controls on the AXLOC-FD2 until you hear a slight distortion, then back off slightly until the sound is clean.
  5. Ajustar AmpGuany lifier: Once the AXLOC-FD2 gain is set, slowly increase the gain control on your amplifier until the desired volume is achieved without distortion.
  6. Afinament: Make small adjustments to both the AXLOC-FD2 and amplifier gains as needed to achieve the best sound quality. Avoid setting gains too high, as this will introduce distortion and can damage speakers.

Manteniment

The Axxess AXLOC-FD2 is designed for reliable, maintenance-free operation. No user-serviceable parts are inside. To ensure longevity:

  • Mantingueu la unitat lliure de pols i deixalles.
  • Assegureu-vos que totes les connexions de cablejat romanguin segures.
  • Eviteu exposar la unitat a temperatures o humitat extremes.

Resolució de problemes

ProblemaCausa possibleSolució
No audio output from ampmés viu
  • Loose RCA connections
  • No remote turn-on signal to ampmés viu
  • Incorrect input wiring to AXLOC-FD2
  • Amplifier not powered
  • Check and secure all RCA cables.
  • Verify remote turn-on wire is connected and receiving 12V.
  • Double-check speaker input wiring from factory radio.
  • Assegureu-vos amplifier has power and ground connections.
So distorsionat o de mala qualitat
  • Gain levels set too high
  • Mala connexió a terra
  • Incorrect speaker polarity
  • Re-adjust gain settings on AXLOC-FD2 and amplifier (refer to Operating Instructions).
  • Verify a solid, clean ground connection for both AXLOC-FD2 and ampmés viu.
  • Check speaker wire polarity; ensure positive and negative are consistent.
Hissing or whining noise
  • Interferència del bucle de terra
  • Cables RCA de mala qualitat
  • Ensure all components are grounded to the same point.
  • Try routing RCA cables away from power wires.
  • Consider using higher quality shielded RCA cables.

Especificacions

  • Model: AXLOC-FD2
  • Canals: 2-Canals
  • Tipus d'entrada: High-level (speaker level)
  • Tipus de sortida: Low-level (RCA)
  • Compatibilitat: Ford vehicles 2011-Up
  • Característiques: Adjustable gain, 12V remote turn-on output
  • Pes de l'article: Aproximadament 1.37 lliures
  • Dimensions del paquet: Aproximadament 10.39 x 10.31 x 4.92 polzades

Garantia i Suport

Per obtenir informació sobre la garantia o assistència tècnica, consulteu el lloc web oficial del fabricant. weblloc web o poseu-vos en contacte amb el seu departament d'atenció al client. Conserveu el comprovant de compra per a reclamacions de garantia.

Fabricant: Axxess

Weblloc: axxessinterfaces.com (Exampl'enllaç, l'enllaç real pot variar)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.