WONDOM ADAU1701 DSP PreamplificadorampManual d'instruccions del processador de senyal digital de 2 entrades i 4 sortides

Introducció

This manual provides detailed instructions for the installation, operation, and maintenance of your WONDOM ADAU1701 DSP Preamp. This unit is designed for advanced audio signal processing, offering a 2-input, 4-output configuration with digital crossover capabilities and support for SigmaStudio programming.

Les característiques clau inclouen:

• Powered by ADAU1701 DSP, a 28/56bit Digital Signal Processor Engine.
• 24bit ADC/DAC Resolution Ratio with a 48kHz Sampling Tarifa.
• Unbalanced 2-Input, 4-Output Preamp Unitat.
• USB Type-C Port for DC 5V Power.
• Four Potentiometers for High-Pass Filter (HPF), Low-Pass Filter (LPF), and Volume Control.
• Integrated Mute & Phase Switches.
• Supports SigmaStudio Programming when connected with an ICP5 programmer.
• Open-sourced Demo Program & HEX Files are provided for restoring factory settings.

Contingut del paquet

Si us plau, verifiqueu que tots els elements siguin presents al paquet:

• WONDOM ADAU1701 DSP Preamplificadoramp Unitat
• USB Type-C Cable (for power)
• Manual d'usuari (aquest document)
• (Optional: ICP5 Programmer, sold separately for advanced programming)

Informació de seguretat

• Ensure the power supply matches the device's requirements (DC 5V, 1A via USB Type-C).
• No exposeu la unitat a la humitat ni a temperatures extremes.
• Avoid opening the enclosure unless you are a qualified technician.
• Mantenir fora de l'abast dels nens.

Configuració

1. Connexions físiques

Refer to the diagrams below for proper connection of audio inputs, outputs, and power.

Figura 1: Connexions del panell posterior. This image shows the rear panel of the ADAU1701 DSP Preamp, highlighting the DC Input (5V, 1A), ICP Port, Line In (ADC0 Left, ADC1 Right), and Line Out (DAC0 Right, DAC1 Left, DAC2 Right, DAC3 Left) RCA jacks.

• Connexió d'alimentació: Connect a DC 5V, 1A power supply to the USB Type-C port labeled "DC INPUT 5V, 1A" on the rear panel.
• Entrada d'àudio: Connect your audio source (e.g., media player, pre-amplifier) to the "LINE IN" RCA jacks (ADC0 Left, ADC1 Right).
• Sortida d'àudio: Connecteu el vostre amplifiers or powered speakers to the "LINE OUT" RCA jacks. The default configuration provides 2-channel mid-range output (DAC2 Right, DAC3 Left) and 2-channel bass output (DAC0 Right, DAC1 Left) for a 2-way digital crossover setup.
• ICP Port: This port is used for connecting an ICP5 programmer (sold separately) for advanced SigmaStudio programming.

2. Engegada inicial

Once all connections are secure, apply power to the unit. The "POWER" LED on the front panel should illuminate, indicating the device is operational.

Instruccions de funcionament

The WONDOM ADAU1701 DSP Preamp features several controls on its front panel for direct adjustment, as well as advanced programming capabilities via SigmaStudio.

Figura 2: Controls del panell frontal. This image displays the front panel, showing the Power LED, Busy LED, SW1 (Mute) and SW2 (Phase) switches, and four potentiometers (POT1, POT2, POT3, POT4) for various audio adjustments.

Controls del panell frontal:

• LED d'alimentació: Indica que la unitat està encesa.
• BUSY LED: Indicates DSP activity.
• SW1 (Mute Switch): Toggles audio output mute on/off.
• SW2 (Phase Switch): Adjusts the phase of the audio output.
• POT1 (MP3 / ADC2): Controls the High-Pass Filter (HPF) for Bank B (3kHz-20kHz).
• POT2 (MP8 / ADC3): Controls the Low-Pass Filter (LPF) for Bank A (210Hz-3kHz).
• POT3 (MP9 / ADC0): Controls the High-Pass Filter (HPF) for Bank A (10Hz-310Hz).
• POT4 (VOL): Controla el volum general.

Digital Crossover Configuration:

The unit's default output is configured as a 2-way digital crossover, providing dedicated outputs for bass and mid-range frequencies.

Figure 3: 2-In, 4-Out Digital Crossover. This diagram shows the RCA jack assignments for 2-channel Line Input, 2-channel Mid-range Output, and 2-channel Bass Output, facilitating a 2-way digital crossover setup.

• 2CH Line Input: ADC0 Left (White), ADC1 Right (Red).
• 2CH Mid-range Output: DAC2 Right (Red), DAC3 Left (White).
• 2CH Bass Output: DAC0 Right (Red), DAC1 Left (White).

SigmaStudio Programming:

For advanced customization and fine-tuning of the DSP functions, the unit supports programming via Analog Devices' SigmaStudio software. An ICP5 programmer (sold separately) is required to connect the DSP unit to your computer.

Figure 4: SigmaStudio Programming Setup. This image illustrates the connection between the DSP unit and an ICP5 programmer, along with a visual representation of the SigmaStudio graphical programming interface.

• Programari: Download and install SigmaStudio from the Analog Devices weblloc.
• Maquinari: Connect the ICP5 programmer to the ICP Port on the DSP unit and to your computer via USB.
• Programació: Utilize the open-sourced demo program and HEX files provided by WONDOM to get started or to restore factory settings. All terminal functions can be tailored to specific needs using SigmaStudio.

Manteniment

• Mantingueu la unitat neta netejant-la amb un drap suau i sec.
• Eviteu utilitzar productes químics aggressivs o netejadors abrasius.
• Assegureu-vos que hi hagi una ventilació adequada al voltant de la unitat per evitar el sobreescalfament.
• Comproveu regularment totes les connexions dels cables per assegurar-vos que estiguin ben ajustades.

Resolució de problemes

Especificacions

Garantia i Suport

WONDOM products are manufactured by Sure Electronics. For warranty information, technical support, and further assistance, please refer to the official Sure Electronics weblloc web o contacteu directament amb el servei d'atenció al client. Conserveu el rebut de compra com a comprovant de compra per a reclamacions de garantia.

Manufacturer: Sure Electronics

For additional resources and community support regarding SigmaStudio programming, online forums and tutorials can be a valuable resource.