FMS HT-TX02

FMS RC 2.4G HT-TX02 Radio Transmitter User Manual

Model: HT-TX02

Introducció

Welcome to the FMS RC 2.4G HT-TX02 Radio Transmitter user manual. This transmitter is designed for precise control of 1/18 scale RC vehicles, including the FJ Cruiser, K10, and HILUX models. Please read this manual thoroughly before operation to ensure safe and optimal performance.

Informació de seguretat

  • Feu servir sempre el vostre vehicle RC en zones obertes lluny de persones, mascotes i obstacles.
  • Never operate the transmitter with low batteries.
  • Keep the transmitter away from water and moisture.
  • This product is not a toy. Recommended for ages 14 and up.
  • Disconnect the vehicle's battery when not in use.

Contingut del paquet

  • FMS HT-TX02 2.4G Radio Transmitter (1 unit)
  • (Note: Receiver is sold separately and not included with this transmitter.)

Transmissor acabatview

The HT-TX02 transmitter features a standard pistol-grip design for comfortable and intuitive control.

FMS HT-TX02 Radio Transmitter front view

Imatge: Frontal view of the FMS HT-TX02 Radio Transmitter, showing the steering wheel, throttle trigger, and main body.

Controls i indicadors

  • Volant: Controla la direcció esquerra i dreta.
  • Activador de l'accelerador: Controls forward, brake, and reverse. Pull for forward, push for brake/reverse.
  • Interruptor d'alimentació: Encén/apaga l'emissor.
  • Indicador LED: Shows power status and binding status.
  • Retall de direcció: Adjusts the neutral steering position.
  • Retall de l'accelerador: Ajusta la posició neutral de l'accelerador.
  • Binding Button: Used for pairing with a compatible receiver.

Configuració

1. Instal·lació de la bateria

The HT-TX02 transmitter requires 4x AAA batteries (not included).

  1. Open the battery compartment cover on the bottom of the transmitter.
  2. Introduïu 4 piles AAA noves, assegurant-vos de la polaritat correcta (+/-).
  3. Tanqueu bé la tapa del compartiment de la bateria.

Avís: No barregeu piles velles i noves. No barregeu piles alcalines, estàndard (carboni-zinc) o recarregables (níquel-cadmi).

2. Binding the Transmitter to a Receiver

This transmitter operates on a 2.4GHz frequency and must be bound to a compatible FMS 2.4G receiver (sold separately) before use.

  1. Ensure the transmitter batteries are installed and the power switch is OFF.
  2. Connect the receiver to your RC vehicle's Electronic Speed Controller (ESC) and power source.
  3. Turn ON the receiver power. The receiver's LED should flash, indicating it is waiting for a binding signal.
  4. While holding down the BIND button on the transmitter, turn ON the transmitter's power switch.
  5. Continue holding the BIND button until the LED indicator on both the transmitter and receiver turns solid, indicating a successful bind.
  6. Deixeu anar el botó BIND.
  7. Turn OFF both the transmitter and receiver, then turn them ON again to confirm the binding.

If binding fails, repeat the steps. Ensure the transmitter and receiver are close to each other during the binding process.

Instruccions de funcionament

Encès

  1. Engegueu primer l'emissor.
  2. Then, turn ON the receiver/vehicle power.

Important: Always power on the transmitter before the vehicle and power off the vehicle before the transmitter to prevent loss of control.

Controls bàsics

  • Direcció: Rotate the steering wheel clockwise for right turns, counter-clockwise for left turns.
  • Acceleració: Pull the trigger towards you for forward movement. Push the trigger away from you for braking, and further for reverse.

Ajustos de retallades

Trim controls allow fine-tuning of the steering and throttle neutral positions.

  • Retall de direcció: If the vehicle pulls left or right when the steering wheel is centered, adjust the steering trim dial until the vehicle tracks straight.
  • Retall de l'accelerador: If the vehicle creeps forward or backward when the throttle trigger is at neutral, adjust the throttle trim dial until the vehicle remains stationary.

Manteniment

  • Neteja: Use a soft, dry cloth to clean the transmitter. Avoid using solvents or harsh chemicals.
  • Emmagatzematge: Store the transmitter in a cool, dry place away from direct sunlight. Remove batteries if storing for extended periods to prevent leakage.
  • Cura de la bateria: Replace batteries when the LED indicator shows low power. Dispose of used batteries responsibly.

Resolució de problemes

ProblemaCausa possibleSolució
El transmissor no s'encén.Piles gastades o instal·lades incorrectament.Comproveu la polaritat de la bateria; substituïu-la per piles noves.
El vehicle no respon a l'emissor.Not bound; low transmitter/receiver battery; out of range.Perform binding procedure; replace batteries; ensure vehicle is within operating range.
Vehicle steers incorrectly.Steering trim is off.Adjust steering trim until the vehicle tracks straight.

Especificacions

  • Model: HT-TX02
  • Freqüència: 2.4 GHz
  • Canals: 2 (Steering, Throttle)
  • Font d'alimentació: 4x piles AAA (no incloses)
  • Dimensions: Aproximadament 4.7 x 2.7 x 4.5 polzades (119 x 69 x 114 mm)
  • Edat recomanada: 14 anys i més
  • Compatibilitat: FMS 1/18 FJ Cruiser, K10, HILUX RC vehicles (requires compatible receiver)

Garantia i Suport

This FMS product is manufactured by RC BAR. For warranty information and technical support, please refer to the documentation provided with your purchase or contact your retailer. Keep your proof of purchase for warranty claims.

Per a més ajuda, podeu visitar el RC BAR Store on Amazon.