BIG RED T83505-2 Torin Pro Series Hydraulic Low Profile Jack de pis

Producte acabatview

The BIG RED T83505-2 Torin Pro Series Hydraulic Low Profile Floor Jack is engineered for general and heavy-duty industrial use, offering a substantial 3.5 ton (7,000 lb.) lifting capacity. Its low-profile design allows access under vehicles with minimal ground clearance, with a lift range extending from 3.25 inches to 22 inches. Constructed from high-strength steel with a rust-resistant powder-coated finish, this jack is built for durability. The dual pump system provides rapid lifting, making it efficient for various cars, trucks, and SUVs. Maneuverability is enhanced by two large steel casters and two 360-degree swivel casters. For safety, it incorporates a built-in overload system to prevent use beyond its rated capacity, and a wide stance ensures stability during operation.

Informació important de seguretat

WARNING: Read, understand, and follow all instructions and warnings before using this product. Failure to do so may result in property damage, serious injury, or death.

• Always use this jack on a hard, level surface.
• No supereu la capacitat nominal de 3.5 tones (7,000 lliures).
• This jack is a lifting device only. Immediately after lifting, support the vehicle with appropriate jack stands. Do not work under a vehicle supported only by the jack.
• Ensure the vehicle is in park (or gear for manual transmission) and the parking brake is engaged. Block wheels that are not being lifted.
• Centreu la càrrega a la sella. Les càrregues descentrades poden fer que el gat es bolqui.
• No utilitzeu el gat per a altres finalitats que no siguin aixecar vehicles.
• Mantingueu les mans i els peus allunyats de les parts mòbils i de la zona sota la càrrega.
• Utilitzeu equips de seguretat adequats, inclosa la protecció ocular.
• Inspect the jack before each use. Do not use if damaged, altered, or leaking hydraulic fluid.
• Només personal qualificat ha de realitzar el manteniment o les reparacions.

Què hi ha a la caixa

• 1 x BIG RED T83505-2 Hydraulic Low Profile Jack de pis
• 1 x Muntatge de mànec
• 1 x Manual d'usuari (aquest document)

Components i característiques

Figura 1: Davant view of the BIG RED T83505-2 Floor Jack. This image shows the overall design, including the lifting arm, saddle, and front wheels.

Figura 2: lateral view of the floor jack with the handle inserted. This perspective highlights the low-profile design and the handle's attachment point.

Figura 3: The floor jack in its fully lowered position, showcasing its minimal height for accessing low-clearance vehicles.

Figura 4: Un detallat view of the dual pump mechanism and the robust springs, illustrating the quick lift system.

Figura 5: Close-up of the rear 360-degree swivel casters and the lifting saddle, designed for smooth positioning and secure load contact.

The jack features a large steel saddle for secure contact with the vehicle's lifting point, a long handle for leverage and control, and durable steel and swivel casters for easy movement. The dual piston quick lift pump significantly reduces the number of strokes required to lift a load.

Configuració i preparació inicial

1. Desembalatge: Traieu amb cura el gat i tots els components de l'embalatge. Inspeccioneu-ho per si hi ha hagut danys durant l'enviament.
2. Muntatge del mànec: Insert the handle into the handle socket on the jack. Align the holes and secure it with the provided screw or pin, ensuring it is firmly seated.
3. Purging Air from Hydraulic System (Bleeding):
   • With the jack fully lowered, remove the oil filler plug (usually a rubber stopper or screw on the hydraulic cylinder).
   • Pump the handle rapidly 10-15 times to remove any trapped air.
   • Substituïu el tap d'ompliment d'oli.
   • Test the jack by lifting it to its full height and then lowering it completely. Repeat a few times. If the jack does not lift smoothly or reaches full height, repeat the bleeding process.

Instruccions de funcionament

1. Preparar el vehicle: Park the vehicle on a hard, level surface. Engage the parking brake and place the transmission in park (or lowest gear for manual). Block the wheels that are not being lifted to prevent accidental movement.
2. Col·loca el Jack: Locate the vehicle manufacturer's recommended lifting points. Slide the jack under the vehicle, positioning the saddle directly under the designated lifting point. Ensure the jack is stable and the load is centered on the saddle.
3. Aixecar el vehicle: Close the release valve by turning the handle clockwise until it is firmly closed. Pump the handle up and down to raise the vehicle to the desired height. Lift only high enough to allow for the placement of jack stands.
4. Assegurar amb suports hidràulics: Immediately after lifting, place appropriately rated jack stands under the vehicle's designated support points. Ensure the vehicle is securely resting on the jack stands before proceeding. NEVER work under a vehicle supported only by the floor jack.
5. Baixar el vehicle: Once work is complete and jack stands are removed (ensure they are clear of the vehicle), slowly open the release valve by turning the handle counter-clockwise. The vehicle will begin to lower. Control the lowering speed by adjusting how much you open the valve.
6. Treure el Jack: Once the vehicle is fully lowered and resting on its wheels, remove the floor jack.

Figura 6: The floor jack correctly positioned under a vehicle's front axle, with additional jack stands providing crucial support. Always use jack stands when working under a vehicle.

Figura 7: Un altre view of the floor jack and jack stands in use, demonstrating proper vehicle support during maintenance or repair.

Manteniment

• Lubricació: Periodically lubricate all moving parts, including the pivot points, casters, and handle mechanism, with light machine oil.
• Fluid hidràulic: Check the hydraulic fluid level every 6 months. With the jack fully lowered and on a level surface, remove the oil filler plug. The fluid level should be just below the filler hole. If low, add high-quality hydraulic jack oil (ISO VG 15 or equivalent). Do not use brake fluid or motor oil.
• Neteja: Keep the jack clean and free of dirt, grease, and debris. Wipe down the ram and pump plungers regularly.
• Emmagatzematge: Guardeu el gat en un lloc net i sec amb el pistó completament retret per evitar la corrosió i allargar la vida útil del segell.
• Inspecció: Before each use, inspect the jack for any signs of damage, wear, or leaks. Pay attention to welds, casters, and the hydraulic cylinder. Do not use a damaged jack.

Resolució de problemes

Especificacions

Informació de la garantia

This BIG RED T83505-2 Torin Pro Series Hydraulic Low Profile Floor Jack includes a limited 1-year manufacturer warranty. This warranty covers defects in materials and workmanship under normal use. For warranty claims or further details, please refer to the warranty card included with your product or contact the manufacturer directly.

Atenció al client

For technical assistance, parts inquiries, or general support regarding your BIG RED T83505-2 Floor Jack, please contact Torin customer service. Have your model number (T83505-2) and purchase information ready when contacting support.

Please note: Contact information for the manufacturer is typically provided on the product packaging or within the included warranty documentation.