JOROBURO S866 Electric Bike LCD Display User Manual

1. Introducció

This manual provides detailed instructions for the installation, operation, and maintenance of your JOROBURO S866 Electric Bike LCD Display. Designed for electric bicycles and scooters, this display offers essential riding data and control functions. Please read this manual thoroughly before use to ensure proper function and safety.

2. Informació de seguretat

• Ensure the display is securely mounted and all connections are waterproof before riding.
• Do not attempt to disassemble or modify the display.
• Always prioritize road safety. Do not operate the display while riding if it distracts you.
• Verify compatibility with your e-bike's controller (UART No. 2 protocol, 5-pin plug) before installation to prevent damage.

3. Contingut del paquet

• 1 x JOROBURO S866 LCD Display
• 1 x Manual d'instruccions (aquest document)

4. Producte acabatview

The S866 LCD display features a clear screen and intuitive buttons for easy control and monitoring of your e-bike's performance.

Figura 4.1: Davant view of the JOROBURO S866 LCD Display, showing the screen and control buttons.

4.1 Display Components

• Pantalla LCD: Displays speed, battery level, assist level, trip distance, and other data.
• Botó '+': Increases assist level, navigates menu up.
• 'Power' Button: Turns display on/off, confirms selections, enters menu.
• Botó '-': Decreases assist level, navigates menu down.
• Connector impermeable de 5 pins: For connection to the e-bike controller.

Figura 4.2: Primer pla view of the display's control buttons: Plus (+), Power, and Minus (-).

5. Instal·lació

1. Muntatge: Attach the display bracket to your e-bike's handlebars (suitable for 22.5mm handlebars). Secure it firmly using the provided screw.


Figura 5.1: Dimensions of the S866 LCD Display and its integrated mounting bracket.

2. Connexió: Locate the 5-pin UART No. 2 protocol connector on your e-bike's controller. Align the pins and firmly connect the display's waterproof connector. Ensure a secure fit to prevent water ingress.

Figura 5.2: The 5-pin waterproof connector of the S866 LCD Display.
3. Gestió de cables: Route the cable safely, ensuring it does not interfere with steering or moving parts. Use cable ties if necessary.

6. Instruccions de funcionament

6.1 Encès/Apagat

• To turn on the display, press and hold the 'Power' button for approximately 2 seconds.
• To turn off the display, press and hold the 'Power' button for approximately 2 seconds.

6.2 Adjusting Assist Level

• Press the '+' button to increase the pedal assist level.
• Press the '-' button to decrease the pedal assist level.
• The current assist level will be displayed on the screen.

6.3 Informació mostrada

The S866 display provides the following information:

• Velocitat: Current riding speed (km/h or mph).
• Nivell d'assistència: Current pedal assist level (e.g., 0-5).
• Nivell de bateria: Graphical representation of remaining battery charge.
• Distància del viatge: Distància recorreguda durant el trajecte actual.
• Odòmetre: Total distance covered by the e-bike.

Figura 6.1: The S866 display showing various riding parameters.

6.4 Accessing Settings (P-Settings)

To access advanced settings (P-settings), typically press and hold the '+' and '-' buttons simultaneously for a few seconds while the display is on. Navigation within the menu is usually done with '+' and '-' buttons, and selection/confirmation with the 'Power' button. Common settings include:

• P01: Backlight brightness (1-3 levels).
• P02: Mileage unit (0: km, 1: mile).
• P03: Voltage level (24V, 36V, 48V). Important: Set this correctly to match your e-bike's battery voltage.
• P04: Sleep mode time (0: never, 1-60 minutes).
• P05: Assist gear (0: 3 gears, 1: 5 gears).
• P06: Wheel diameter (inches).
• P07: Speed magnet number.
• P08: Speed limit.
• P09: Zero start/Non-zero start (0: zero start, 1: non-zero start).
• P10: Drive mode (0: pedal assist only, 1: electric only, 2: both).
• P11: Assist sensitivity.
• P12: Assist start strength.
• P13: Magnet disk type (5, 8, 12).
• P14: Controller current limit.
• P15: Undervoltage valor.
• P16: ODO reset.
• P17: Cruise control (0: off, 1: on).
• P18: Password setting (if applicable).

Note: The exact P-settings and their functions may vary slightly. Refer to your e-bike's controller manual for specific details if available. Incorrect settings can affect performance or damage components.

7. Manteniment

• Neteja: Netegeu la pantalla i el cos amb un drap suau iamp tela. No utilitzeu netejadors abrasius ni dissolvents.
• Exposició a l'aigua: Tot i que el connector és impermeable, eviteu submergir la pantalla. Si es mulla, eixugueu-la bé abans d'utilitzar-la.
• Emmagatzematge: Store the e-bike and display in a dry, cool place when not in use.

8. Solució De Problemes

9. Especificacions

• Model: S866
• Marca: JOROBURO
• Material: ABS
• Voltage Compatibilitat: 24V, 36V, 48V (auto-detect or configurable via P-settings)
• Tipus de connector: 5-Pin Waterproof Connector
• Protocol: UART núm. 2
• Tipus de visualització: LCD amb llum de fons
• Dimensions (Display Unit): Approximately 8cm (3.1in) x 4.8cm (1.9in) x 4.8cm (1.9in)
• Longitud del cable: Approximately 21cm (8.3in)
• Pes: 3.52 unces (aprox. 100 g)
• Manillar Clamp Diàmetre: Designed for 22.5mm handlebars

Figura 9.1: Detailed dimensions of the S866 LCD Display.

10. Garantia i Suport

This product is covered by a standard manufacturer's warranty against defects in materials and workmanship. For warranty claims, technical support, or further assistance, please contact your retailer or the JOROBURO customer service department. Keep your purchase receipt as proof of purchase.

For general inquiries or to learn more about JOROBURO products, please visit the official brand website or contact customer support through your purchase platform.