Wisoqu MC701 Digital PID Temperature Controller User Manual

1. Producte acabatview

The Wisoqu MC701 is a digital PID temperature controller designed for precise temperature management in various industrial and scientific applications. It features a PVSV (Process Value/Set Value) display, supports both K-type thermocouples and PT100 RTD sensors, and offers integrated Relay and SSR outputs for versatile control. The unit also supports Celsius (℃) and Fahrenheit (℉) temperature display conversion.

2. Característiques clau

• High Resolution Display: When a thermocouple is used, the digital display resolution can be 0.1 ℃ / 0.1 ℉.
• Dual Output Integration: Features integrated Relay and SSR outputs, allowing users to select the appropriate output type.
• Temperature Unit Conversion: Supports both Celsius (℃) and Fahrenheit (℉) temperature display.
• Compact Design: Short shell design with only 85mm depth for easy mounting and installation.
• Accurate Control: Built-in high-performance chip ensures high sensitivity and accurate temperature control.

3. Informació de seguretat

Please read all instructions carefully before installation and operation. Failure to follow these instructions may result in equipment damage, personal injury, or improper operation.

• Seguretat elèctrica: Ensure all power connections are made by a qualified electrician and comply with local electrical codes. Disconnect power before wiring or servicing the unit.
• Voltage Compatibilitat: Comproveu que la font d'alimentació voltage matches the controller's specifications (85-265VAC).
• Connexió a terra adequada: Assegureu-vos que la unitat estigui correctament connectada a terra per evitar descàrregues elèctriques.
• Condicions ambientals: Do not expose the controller to excessive moisture, dust, corrosive gases, or extreme temperatures outside its operating range.
• Ús previst: Use this device only for its intended purpose of temperature control.

4. Product Components and Diagram

Familiarize yourself with the controller's front panel and wiring terminals.

Figura 4.1: Tauler frontal View
This image displays the front panel of the MC701 controller, showing the red PV (Process Value) display, the green SV (Set Value) display, and the control buttons: SET, R/S (Run/Stop or Reset/Set), Down arrow, and Up arrow. Indicators for OUT (Output), AT (Auto-tuning), ALM1 (Alarm 1), and ALM2 (Alarm 2) are also visible.

Figure 4.2: Wiring Terminal Diagram
Aquesta imatge ofereix una vista de dalt a baix view of the MC701 controller's terminal block, illustrating the wiring connections. It shows terminals for 85-265VAC power input (8, 9), AL1 (Alarm 1) output (1, 2), SSR output (10, 11), RTD/TC input (3, 4, 5, 6, 7), and Relay output (12, 13, 14).

Figura 4.3: Dimensions del producte
Aquesta imatge mostra un costat view of the MC701 controller with its physical dimensions indicated. The front panel measures 72mm x 72mm (2.8in x 2.8in), and the depth of the unit is 85mm (3.3in).

5. Configuració i instal·lació

5.1 Muntatge

The MC701 controller is designed for panel mounting. Refer to Figure 4.3 for dimensions. Ensure adequate space for ventilation and wiring connections at the rear of the unit.

5.2 Connexions de cablejat

Refer to Figure 4.2 for the wiring terminal diagram. All wiring should be performed with power disconnected.

1. Font d'alimentació (85-265 VCA): Connect the main power supply to terminals 8 and 9.
2. Entrada del sensor:
   • K-Type Thermocouple (TC): Connect the positive (+) lead to terminal 6 and the negative (-) lead to terminal 7.
   • PT100 RTD: Connect the two signal wires to terminals 4 and 5. If using a 3-wire PT100, connect the third compensation wire to terminal 3.
3. SSR Output: Connect the Solid State Relay (SSR) control input to terminals 10 (+) and 11 (-).
4. Sortida de relé: Connect the load to the relay contacts. Terminal 12 is Normally Open (NO), Terminal 13 is Common (COM), and Terminal 14 is Normally Closed (NC).
5. Alarm Output (AL1): Connect alarm devices to terminals 1 and 2.

5.3 Engegada inicial

After all connections are securely made, apply power to the unit. The controller will perform a self-test, and the PV and SV displays will illuminate.

6. Instruccions de funcionament

6.1 Mostra finalview

• VA (Valor del Procés): The upper red display shows the current measured temperature from the sensor.
• SV (Valor definit): The lower green display shows the desired target temperature.
• Indicador OUT: Illuminates when the output (Relay or SSR) is active.
• Indicador AT: Illuminates during the auto-tuning process.
• Indicadors ALM1/ALM2: Illuminate when the respective alarm conditions are met.

6.2 Configuració de la temperatura objectiu (SV)

1. Premeu el botó SET el botó una vegada. La pantalla SV començarà a parpellejar.
2. Utilitza el ▲ (Amunt) i ▼ (Avall) arrow buttons to adjust the SV to your desired temperature.
3. Premeu el botó SET button again to confirm and save the new SV. The display will stop flashing.

6.3 Accessing Parameter Settings

To access advanced parameters (e.g., PID settings, alarm values, sensor type, ℃/℉ conversion):

1. Manteniu premut el botó SET durant aproximadament 3-5 segons fins que aparegui el primer codi de paràmetre a la pantalla PV.
2. Utilitza el ▲ (Amunt) i ▼ (Avall) arrow buttons to navigate through the parameter codes.
3. Premeu SET a view el valor del paràmetre seleccionat.
4. Utilitza el ▲ (Amunt) i ▼ (Avall) arrow buttons to change the parameter value.
5. Premeu SET again to save the new value and move to the next parameter, or press R/S to exit the parameter setting mode without saving the current parameter change.

6.4 Auto-Tuning (AT)

Auto-tuning helps the controller optimize its PID parameters for your specific system, leading to more stable and accurate temperature control.

1. Set the desired SV.
2. Manteniu premut el botó R/S button for approximately 3-5 seconds. The AT indicator will illuminate, and the controller will begin the auto-tuning process.
3. Allow the system to cycle through several heating/cooling periods. The AT process is complete when the AT l'indicador s'apaga.
4. To stop auto-tuning manually, press and hold the R/S button again for 3-5 seconds.

7. Manteniment

The Wisoqu MC701 controller requires minimal maintenance to ensure long-term reliable operation.

• Neteja: Periodically wipe the front panel with a soft, dry cloth. Do not use abrasive cleaners or solvents. Ensure no liquids enter the unit.
• Control ambiental: Regularly inspect the operating environment to ensure it remains free from excessive dust, moisture, and corrosive substances.
• Inspecció del cablejat: Comproveu periòdicament totes les connexions del cablejat per comprovar si estan ben ajustades i si hi ha signes de desgast o danys.
• Ventilació: Ensure that the ventilation openings on the sides of the unit are not obstructed to prevent overheating.

8. Solució De Problemes

If you encounter issues with your MC701 controller, refer to the following common problems and solutions:

If the problem persists after attempting these solutions, please contact Wisoqu customer support for further assistance.

9. Especificacions

10. Garantia i Suport

Wisoqu products are designed for reliability and performance. For warranty information, technical support, or service inquiries, please refer to the documentation included with your purchase or contact Wisoqu customer service through their official channels. Please have your product model (MC701) and purchase details available when contacting support.