Manual d'usuari del kit de marc HGLRC Rekon7 Long Range PRO HD O3

1. Introducció

This manual provides detailed instructions for the assembly, setup, and maintenance of your HGLRC Rekon7 Long Range PRO HD O3 Frame Kit. This frame is designed for 7-inch FPV racing drones, offering durability and compatibility for extended flight times.

Advertència de seguretat: Always ensure all components are securely fastened before flight. Incorrect assembly or loose parts can lead to equipment damage or injury. Disconnect power before performing any maintenance or assembly.

2. Contingut del paquet

Verifiqueu que tots els components següents estiguin inclosos al paquet:

• 1x 2mm top plate
• 1x 2mm base plate
• 1x 2mm mid plate
• 2x 6mm front arm
• 2x 6mm rear arm
• 2x 2mm rack protection board
• 2x 2mm camera side panel
• 2x 4mm Arm Reinforcement rod
• 2x M3*28mm black mesh aluminum column
• 4x M3*20mm black mesh aluminum column
• 2x M3*18mm black mesh aluminum pillar
• 4 x M4 * 12 cargols
• 4 x M3 * 20 cargols
• 4 x M3 * 16 cargols
• 4 x M3 * 10 cargols
• 8 x M3 * 8 cargols
• 4 x M2 * 20 cargols
• 1 x M2 * 16 cargols
• 1 x M2 * 10 cargols
• 2 x M2 * 4 cargols
• 1x M5 lock nut (red)
• 4x M3 self-locking nuts
• 5x M2 self-locking nuts
• 8x M3*8 shock-absorption balls
• 4x M2*4 shock-absorption balls
• 2x battery straps 20x250mm
• 1x Battery Anti-slip pad
• 1x TPU black GoPro holder mount
• 1x TPU black GPS mount
• 1x TPU black antenna mount
• 1x TPU black T-antenna mount
• 1x TPU black buzzer mount
• 1x TPU black DJI Air unit Block A
• 1x TPU black DJI Air unit Block B
• 1x TPU black DJI O3 holder mount
• 1x TPU black Camera converting seat

3. Instruccions de muntatge

Follow these steps to assemble your Rekon7 LR Pro Frame Kit. Refer to the diagrams for visual guidance.

3.1 Base Frame Assembly

1. Attach the 6mm front and rear arms to the 2mm base plate using the appropriate M3 screws and self-locking nuts. Ensure the arms are oriented correctly.
2. Secure the 2mm rack protection boards to the arms.
3. Install the 4mm Arm Reinforcement rods for added structural integrity.

Figura 1: Mésview of the assembled Rekon7 LR Pro Frame, showcasing the carbon fiber arms and central structure.

3.2 Central Stack and Camera Mount

4. Mount the 2mm mid plate onto the base plate using the M3 aluminum columns.
5. Attach the 2mm camera side panels to the front of the frame. These panels support 19x19mm or 20x20mm cameras.

Figura 2: Frontal view of the frame, highlighting the camera mounting area and central stack.

3.3 Top Plate and TPU Mounts

6. Install the 2mm top plate, securing it with the remaining M3 aluminum columns. The space between the top and middle plate is 20mm.
7. Attach the various TPU mounts as needed: GoPro holder, GPS mount, antenna mounts (T-antenna, general antenna), buzzer mount, DJI Air unit blocks, and DJI O3 holder mount.

Figura 3: lateral view of the frame, showing the layered plate design and mounting points for electronics.

4. Instal·lació de components

This frame is designed for compatibility with various FPV drone components. Below are general guidelines for installing recommended parts.

4.1 Flight Controller (FC) and Electronic Speed Controller (ESC)

• The frame supports 20x20mm flight controller mounting holes.
• Mount your FC and ESC stack securely in the central section. Ensure proper isolation from the carbon fiber frame to prevent short circuits.
• Recommended FC: Zeus F722. Recommended ESC: Zeus 48-60A.

4.2 Motors

• The motor mounting holes are 16x16mm or 19x19mm.
• Attach your motors to the arms using the provided M3 screws. Ensure motor wires are routed safely and secured.
• Recommended Motor: 2806.5.

4.3 Camera and Video Transmitter (VTX)

• The frame supports 19x19mm or 20x20mm cameras. Mount the camera between the camera side panels.
• Utilize the TPU DJI Air unit blocks and DJI O3 holder mount for digital FPV systems.
• Recommended Camera: 19x19mm/20x20mm compatible.

4.4 Propellers and Battery

• Install 7-inch propellers onto your motors. Ensure correct rotation direction.
• Secure your battery to the top plate using the provided battery straps and anti-slip pad. The frame is designed to accommodate larger batteries for extended flight times.
• Recommended Propeller: 7 inches. Recommended Battery: 6S 1800-4200mAh.

5. Manteniment

Regular maintenance ensures the longevity and safe operation of your drone frame.

• Inspeccioneu els cargols: Periodically check all screws and nuts for tightness. Vibrations during flight can cause hardware to loosen.
• Carbon Fiber Inspection: Examine carbon fiber plates and arms for cracks or delamination, especially after hard landings. Replace damaged parts immediately.
• TPU Parts: Check TPU mounts for wear or damage. These parts are crucial for securing sensitive electronics.
• Neteja: Keep the frame free from dirt, dust, and debris, which can interfere with electronics or add unnecessary weight.

6. Solució De Problemes

This section addresses common issues related to the frame assembly.

• Vibracions: If your drone experiences excessive vibrations, check for loose motor screws, bent arms, or damaged propellers. Ensure all frame components are tightly secured.
• Component Fitment Issues: Double-check that you are using the correct screws and spacers for each component. Refer to the package contents list and assembly steps.
• Lost Model Buzzer/GPS Issues: Ensure the TPU mounts for the M80 PRO GPS and lost model buzzer are correctly installed and the components are securely seated.
• Signal Loss (TBS Crossfire): Verify that the pre-drilled mounts for TBS Crossfire dual RX/antenna are utilized correctly to optimize signal reception.

7. Especificacions

8. Garantia i Suport

For warranty information, please refer to the terms and conditions provided by your retailer or contact HGLRC directly. Product support and additional resources may be available on the official HGLRC weblloc web o a través de la vostra plataforma de compra.

You can visit the official HGLRC store for more information: HGLRC Store on Amazon