CIPU SFPS14502
CIPU 14-inch Sand Filter System
Model: SFPS14502
Introducció
Thank you for choosing the CIPU 14-inch Sand Filter System. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your new pool filter system. Designed for above-ground swimming pools, this system integrates a 14-inch filter tank with a powerful 0.5HP pump, ensuring crystal clear water with ease of use.
Figura 1: The CIPU 14-inch Sand Filter System, featuring the filter tank and pump unit, positioned beside an above-ground swimming pool.
The system is portable, operating on 115V, and includes a 6-foot power cord for flexible placement. Its 0.5HP high-efficiency pump ensures quiet operation and effective filtration for pools up to 9500 gallons. The reinforced thermoplastic housing provides corrosion resistance and long-lasting performance in all weather conditions.
Figura 2: The filter system is compatible with various above-ground pool types, effectively filtering pools up to 9500 gallons.
Informació de seguretat
Please read all instructions carefully before installing, operating, or performing maintenance on this product. Failure to follow these instructions could result in serious injury or property damage. This product is ETL certified, ensuring it meets recognized safety standards.
Precaucions generals de seguretat:
- Desconnecteu sempre l'alimentació de la bomba abans de realitzar qualsevol servei o manteniment.
- Ensure the electrical outlet is a grounded, GFCI-protected receptacle.
- No feu funcionar la bomba si el cable d'alimentació o l'endoll estan danyats.
- Mantingueu els nens allunyats del sistema de filtre durant el funcionament.
- Install the system on a firm, level surface to prevent tipping.
- Do not bury the power cord. Protect it from sharp edges, oil, grease, hot surfaces, and chemicals.
- Never run the pump dry. Ensure the pump is primed with water before starting.
- Consult a qualified electrician for any electrical questions or issues.
Contingut del paquet
Abans de començar el muntatge, comproveu que totes les peces que s'enumeren a continuació estiguin incloses al paquet. Si falta alguna peça o hi ha alguna danyada, poseu-vos en contacte amb el servei d'atenció al client.
Figura 3: Explotat view of the sand filter system components, showing all included accessories for assembly.
| Ref. No. | Descripció | QTY |
|---|---|---|
| 1 | Vàlvula de 4 vies | 1 |
| 2 | Brida Clamp | 1 |
| 3 | junta tòrica | 1 |
| 4 | Tanc de filtre | 1 |
| 5 | Conjunt de filtres | 1 |
| 6 | Tap de drenatge | 1 |
| 7 | Sand Filter Support | 1 |
| 8 | Screw ST5.5x25mm and Gasket | 4 |
| 9 | junta tòrica | 5 |
| 10 | Adaptador de mànega | 5 |
| 11 | Mànega Clamp | 2 |
| 12 | 1 1/4"(32mm)x45cm hose | 1 |
| 13 | 0.5HP Pump (115V-60Hz) | 1 |
| 14 | Escut de sorra | 1 |
| 15 | Manòmetre | 1 |
| 16 | Plug W/O-ring 1 1/2# MIP | 1 |
| 17 | Cinta de tefló | 1 |
| 18 | Adaptador curt | 2 |
| 19 | Short Adapter Gasket | 2 |
Configuració i instal·lació
Follow these steps to properly assemble and install your sand filter system.
Vídeo 1: A comprehensive guide to setting up the CIPU Sand Filter Pump System for above-ground pools, demonstrating assembly and connection steps.
Assemblea inicial:
- Instal·leu el tap de drenatge: Attach the drain plug (6) to the bottom of the filter tank (4). Ensure the O-ring (9) is properly seated for a watertight seal.
- Assemble Multi-Port Valve: Attach the hose adaptors (10) to the 4-way valve (1) ports. Ensure O-rings (9) are in place.
- Load Filter Media: Place the sand shield (14) over the filter tube inside the tank. Carefully add fine silica sand (0.018 to 0.022 inches in size) into the filter tank. The 14-inch tank holds approximately 75 lbs of sand. Fill to the indicated level on the tank.
- Attach 4-Way Valve: Place the 4-way valve (1) onto the top of the filter tank (4), aligning the central pipe. Secure it with the flange clamp (2) and tighten the screws (8) evenly.
- Instal·leu el manòmetre: Screw the pressure gauge (15) into the designated port on the 4-way valve.
- Muntar la bomba: Secure the 0.5HP pump (13) to the sand filter support (7) using the provided screws (8) and washers.
Figura 4: Key components of the 14-inch filter pump, including the 4-way control valve and pressure gauge.
Connexió a la piscina:
- Connexions de mànega: Connect the pool hoses (not included, use common 1.5" PVC tubing or discharge hoses) to the pump and filter system. The pump is designed for 1.5-inch threaded pool hoses or 1-1/2" or 1-1/4" pool hoses with clamps.
- Pump to Filter: Connect the pump's discharge port to the
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.