GODIYMODULES LD1500SB Constant Current LED Driver Module Instruction Manual

1. Producte acabatview

The GODIYMODULES LD1500SB is a versatile constant current LED driver module designed to provide adjustable output current for various LED applications. It operates within a DC input voltage range of 2.9V to 6.1V and offers an adjustable output current from 28mA to 1500mA, with a maximum output power of 8W. This module is suitable for driving 1 to 16 LEDs within its voltage i límits de corrent.

1.1. Característiques clau

• Entrada Voltage: DC 2.9V - 6.1V
• Output Current: 28mA - 1500mA (Adjustable)
• Potència de sortida màxima: 8 W
• Output Current Accuracy: ±5%
• Low Dropout Voltage: 0.37 V @ 1.5 A
• Integrated Chip Temperature Regulation
• Protecció de corrent LED
• Rang de temperatura de funcionament: -40 ° C a + 85 ° C
• Current Regulation via Adjustable Resistor or PWM Control

1.2. Contingut del paquet

Cada paquet conté:

• 2 x GODIYMODULES LD1500SB Constant Current LED Driver Modules

Image: Two GODIYMODULES LD1500SB LED Driver Modules, showing their compact size and components.

2. Especificacions

3. Configuració i instal·lació

The LD1500SB module offers two primary methods for current regulation: using an adjustable resistor on the module itself or via an external PWM signal. Ensure all connections are secure and correct before applying power.

3.1. Wiring Diagram Overview

The module features input terminals (IN+, IN-) for power supply and output terminals (L+, L-) for connecting LEDs. An 'EN' pin is available for output enable and PWM control.

Imatge: Superior view of a single LD1500SB module, showing the input (IN+, IN-, EN) and output (L+, L-) terminals, along with the adjustable potentiometer.

3.2. Application 1: Adjustable Current via Onboard Resistor

This method allows you to set the output current using the adjustable potentiometer (trimmer) located on the module.

1. Connect the DC power supply (2.9V-6.1V) to the IN+ i EN- terminals. Ensure correct polarity.
2. Connect your LED(s) in parallel to the L+ i L- terminals. The module can drive 1 to 16 LEDs, provided the total current does not exceed 1.5A and the LED voltage is within the module's operating range.
3. Using a suitable small screwdriver, gently and slowly rotate the adjustable resistor on the module to set the desired output current. Rotating clockwise typically increases the current, while counter-clockwise decreases it.

Image: Diagram illustrating wiring for current adjustment using the onboard potentiometer. Input DC 2.9-6.1V connects to IN+ and IN-. LEDs are connected in parallel to L+ and L-. The potentiometer is shown with arrows indicating increase and decrease of output current.

3.3. Application 2: PWM Regulated Output Current

For dynamic current control, the module supports PWM input on the 'EN' pin. This allows for external control of LED brightness or other effects.

1. First, adjust the onboard adjustable resistor to 0 ohms (minimum resistance) or to the maximum desired current. This sets the upper limit for PWM control.
2. Connect the DC power supply (2.9V-6.1V) to the IN+ i EN- terminals.
3. Connect your LED(s) in parallel to the L+ i L- terminals.
4. Connect an MCU (Microcontroller Unit) output PWM signal to the EN pin. The 'EN' pin is an active high output enable and PWM control port. It can be driven by TTL or CMOS logic levels.
5. Ensure the frequency of the PWM signal is less than 2kHz for optimal performance.

Image: Diagram illustrating wiring for PWM current regulation. Input DC 2.9-6.1V connects to IN+ and IN-. LEDs are connected in parallel to L+ and L-. A PWM signal from an MCU is connected to the EN pin for controlling the output current.

4. Instruccions de funcionament

Once the module is correctly wired according to your chosen application, operation involves applying power and, if applicable, adjusting the current or providing a PWM signal.

4.1. Current Adjustment (Manual)

For manual current adjustment, ensure the module is powered and LEDs are connected. Use a small, non-conductive screwdriver to turn the potentiometer. Observe the LED brightness or measure the current with an ammeter to achieve the desired output. Avoid excessive force when turning the potentiometer.

4.2. PWM Control

When using PWM control, the output current will be proportional to the duty cycle of the PWM signal applied to the EN pin. A higher duty cycle will result in higher LED current (up to the limit set by the potentiometer), and a lower duty cycle will result in lower current. Ensure your PWM source is stable and within the specified frequency range (<2kHz).

5. Manteniment

The LD1500SB LED driver module is designed for reliable operation with minimal maintenance. Follow these guidelines to ensure longevity:

• Mantenir sec: Avoid exposure to moisture or liquids, which can damage the electronic components.
• Neteja: Keep the module free from dust and debris. Use a soft, dry brush or compressed air for cleaning if necessary.
• Temperatura: Operate the module within its specified temperature range (-40°C to +85°C). Avoid extreme heat or cold.
• Protecció física: Handle the module with care to prevent physical damage to components or solder joints.
• Power Off Before Adjustments: Always disconnect power before making any wiring changes or significant adjustments to the potentiometer.

6. Solució De Problemes

If you encounter issues with your LD1500SB module, refer to the following troubleshooting steps:

• No LED Output:
  • Comproveu el volum d'entradatage: Ensure DC 2.9V-6.1V is correctly applied to IN+ and IN-.
  • Check LED connections: Verify LEDs are correctly wired to L+ and L- with correct polarity.
  • Check LED functionality: Test LEDs with a known good power source.
  • Potentiometer setting: If using manual adjustment, ensure the potentiometer is not set to minimum current (0mA).
  • PWM signal: If using PWM, ensure the signal is present, active high, and within the <2kHz frequency range. Also, check that the potentiometer is not set to 0 ohms.
• Incorrect Output Current:
  • Potentiometer adjustment: Carefully adjust the onboard potentiometer.
  • PWM signal: If using PWM, verify the duty cycle and frequency of your PWM signal.
  • Load impedance: Ensure the connected LEDs are within the module's voltage i capacitats actuals.
• Sobreescalfament del mòdul:
  • Assegureu-vos que hi hagi una ventilació adequada al voltant del mòdul.
  • Verify that the total power consumption of the LEDs does not exceed the module's 8W maximum output power.
  • Check for short circuits in the LED wiring.

7. Garantia i Suport

The GODIYMODULES LD1500SB LED Driver Module is manufactured by GODIYMODULES. For warranty information or technical support, please contact GODIYMODULES directly through their official channels or the retailer from whom the product was purchased.

Si us plau, consulteu la documentació de compra per conèixer els termes i condicions específics de la garantia.