Valkyrie A360 ARGB All-in-One CPU Liquid Cooler User Manual

1. Introducció

This manual provides detailed instructions for the installation, operation, and maintenance of your Valkyrie A360 ARGB All-in-One (AIO) CPU Liquid Cooler. Please read this manual thoroughly before installation to ensure proper setup and optimal performance. Keep this manual for future reference.

2. Informació de seguretat

• Assegureu-vos que el sistema informàtic estigui apagat i desendollat ​​de la presa de corrent abans de la instal·lació.
• Handle components with care to avoid damage. Avoid touching the cold plate surface directly.
• Do not open the liquid cooler's pump or radiator; it is a sealed unit. Tampering anularà la garantia.
• Mantingueu el producte allunyat de temperatures extremes, humitat i llum solar directa.
• Use only the provided mounting hardware to prevent damage to your CPU or motherboard.

3. Contingut del paquet

Verifiqueu que tots els components que s'enumeren a continuació siguin presents al vostre paquet:

• Valkyrie A360 ARGB AIO Liquid Cooler (Radiator, Pump/CPU Block, Tubing)
• 3 ventiladors ARGB de 120 mm
• Intel Mounting Bracket Kit (LGA 1700, 1200, 115X, 2066, 2011)
• AMD Mounting Bracket Kit (AM5, AM4)
• Fan Screws and Radiator Mounting Screws
• Pasta tèrmica (preaplicada o en tub)
• ARGB Controller/Cables (if included)
• Manual d'usuari

Image: The Valkyrie A360 ARGB AIO Liquid Cooler showing the radiator, three ARGB fans, and the pump/CPU block unit.

4. Configuració i instal·lació

4.1. Preparació

• Apagueu l'ordinador i desconnecteu tots els cables.
• Obriu la carcassa de l'ordinador per accedir a la placa base i a la zona de la CPU.
• Si substituïu un refrigerador existent, traieu-lo amb cura i netegeu qualsevol pasta tèrmica antiga de la superfície de la CPU amb alcohol isopropílic.

4.2. Radiator and Fan Installation

1. Attach the three 120mm ARGB fans to the radiator using the long fan screws provided. Ensure the fan airflow direction is appropriate for your case (typically exhausting air out or pulling air in).
2. Mount the assembled radiator and fans to an available 360mm mounting location in your PC case (e.g., top, front). Use the shorter radiator mounting screws.

Image: The radiator with three white fans attached, ready for case installation.

4.3. CPU Block Installation

1. For Intel Sockets: Install the appropriate Intel backplate behind the motherboard. Attach the Intel mounting standoffs to the motherboard.
2. For AMD Sockets: Remove the stock AMD retention brackets from the motherboard, but keep the original backplate. Attach the AMD mounting standoffs to the motherboard.
3. If thermal paste is not pre-applied to the cold plate, apply a small pea-sized amount to the center of your CPU's Integrated Heat Spreader (IHS).
4. Carefully place the CPU block onto the CPU, aligning the mounting holes with the standoffs.
5. Secure the CPU block with the thumb screws or nuts, tightening them in a diagonal pattern until snug. Do not overtighten.

Imatge: Un primer pla view of the Valkyrie A360 CPU block installed on a motherboard, illuminated with blue ARGB lighting.

4.4. Connexions de cable

1. Connect the pump's 3-pin or 4-pin power cable to the motherboard header labeled "AIO_PUMP," "CPU_OPT," or "SYS_FAN" (consult your motherboard manual for the recommended header).
2. Connect the ARGB cables from the fans and pump to the included ARGB controller or directly to a 5V 3-pin ARGB header on your motherboard. Ensure correct pin alignment to avoid damage.
3. Connect the fan power cables to available fan headers on your motherboard or to a fan hub/controller.

Image: The Valkyrie A360 AIO cooler fully installed within a white PC case, showcasing the blue ARGB lighting on the fans and CPU block.

5. Instruccions de funcionament

5.1. Engegada inicial

After completing the installation, close your PC case, reconnect all external cables, and power on your computer. Observe the cooler for any unusual noises or leaks. Check your system's BIOS/UEFI for CPU temperature readings to confirm proper operation.

5.2. Control d'il·luminació ARGB

If connected to a motherboard's 5V 3-pin ARGB header, you can control the lighting effects using your motherboard's RGB software (e.g., ASUS Aura Sync, MSI Mystic Light, Gigabyte RGB Fusion, ASRock Polychrome Sync). If using the included ARGB controller, refer to its specific instructions for mode and color selection.

Image: The Valkyrie A360 AIO cooler installed in a white PC case, displaying vibrant rainbow ARGB lighting effects on the fans and CPU block.

6. Manteniment

• Neteja de pols: Periodically clean the radiator fins and fan blades to prevent dust buildup, which can impede airflow and cooling performance. Use compressed air or a soft brush.
• Inspecció visual: Regularly check the tubing and connections for any signs of leaks or damage.
• Sense reompliment de refrigerant: The Valkyrie A360 is a sealed AIO unit and does not require coolant refills. Opening the unit will void the warranty.

7. Solució De Problemes

8. Especificacions

9. Garantia i Suport

Valkyrie products are backed by a limited warranty against defects in materials and workmanship. The specific warranty period may vary by region. Please retain your proof of purchase for warranty claims.

For technical support, troubleshooting assistance, or warranty inquiries, please visit the official Valkyrie weblloc web o poseu-vos en contacte amb el seu departament d'atenció al client. La informació de contacte normalment es pot trobar a l'embalatge del producte o a la fitxa oficial weblloc.

Note: Opening the sealed AIO unit or using non-approved components may void your warranty.