Manual d'usuari de la màquina de premsa de calor per a carcasses de telèfon HTVRONT H17

1. Introducció

The HTVRONT H17 Phone Case Heat Press Machine is designed for creating custom sublimation transfers on various items, including phone cases, badges, and coasters. This machine utilizes advanced intelligent temperature control and vacuum heat press technology to ensure vibrant, bubble-free, and full-wrap transfers. This manual provides essential information for safe and effective operation of your device.

Image 1.1: The HTVRONT H17 Phone Case Heat Press Machine. This image displays the compact, light blue heat press machine with its handle and control panel visible.

2. Instruccions de seguretat importants

• Llegiu totes les instruccions abans d'utilitzar l'aparell.
• No toqueu superfícies calentes. Utilitzeu nanses o poms.
• Per protegir-se de les descàrregues elèctriques, no submergiu el cable, els endolls o l'aparell en aigua o altres líquids.
• És necessària una supervisió estreta quan qualsevol aparell és utilitzat per o a prop dels nens.
• Desendolleu la presa de corrent quan no utilitzeu i abans de netejar. Deixeu refredar abans de posar o treure peces.
• No feu servir cap aparell amb un cable o un endoll danyats o després que l'aparell funcioni malament o s'hagi fet malbé de cap manera.
• L'ús d'accessoris no recomanats pel fabricant de l'aparell pot causar lesions.
• No utilitzar a l'aire lliure.
• No deixeu que el cable pengi de la vora de la taula o del taulell, ni toqui superfícies calentes.
• No col·loqueu-lo sobre o prop d'un cremador de gas o elèctric calent, ni en un forn calent.
• Cal extremar la precaució quan es mou un aparell que contingui oli calent o altres líquids calents.
• Connecteu sempre primer l'endoll a l'aparell i després el cable a la presa de corrent. Per desconnectar-lo, gireu qualsevol control a la posició "off" i, a continuació, retireu l'endoll de la presa de corrent.
• No utilitzeu l'aparell per a un altre ús que el previst.

3. Contingut del paquet

Verifiqueu que tots els elements que s'enumeren a continuació s'inclouen al vostre paquet:

• HTVRONT H17 Phone Case Heat Press Machine (x1)
• Phone Case Fixture Set (x1)
• Badge Fixture Set (x1)
• Sublimation Film (A4) (x5 sheets)
• Heat-resistant Gloves (x1 pair)
• Sublimation Badges (58 mm) (x3)
• Tweezers (x1)
• Heat-resistant Tape (x1 roll)

Image 3.1: Contents of the HTVRONT H17 Phone Case Heat Press Kit. This image shows the heat press machine along with included accessories: phone case fixture, badge fixture, sublimation film, heat-resistant gloves, blank sublimation badges, tweezers, and heat-resistant tape.

4. Producte acabatview

The HTVRONT H17 features a user-friendly design with intuitive controls for temperature and time. Its compact size and lightweight construction make it suitable for various crafting environments. The vacuum technology ensures even pressure and full-surface sublimation for professional results.

Image 4.1: Open view of the HTVRONT H17 Heat Press Machine. This image shows the machine with its lid open, revealing the heating plate and the pressing area.

Característiques principals:

• 3D Full-Wrap Vacuum Heat Press: Achieves vibrant, bubble-free transfers that wrap around curves and edges.
• Control precís de la temperatura: Adjustable from 100°C to 180°C (212°F to 356°F) with fine increments.
• Configuració d'hora ajustable: Transfer time can be set from 1 to 600 seconds.
• Universal Adjustable Fixtures: Compatible with various iPhone models (iPhone 12 and above) and Android models (Samsung, Xiaomi, Google, Huawei, etc.) using included fixtures.
• Integrated Design Software Support: Works with IS software for pattern adjustment, mirroring, and outputting sublimation-ready files.
• Funcionament silenciós: Operates at less than 65 dB.
• Lleuger i compacte: Weighs approximately 5.3 kg (11 pounds).

5. Configuració

5.1 Desembalatge i col·locació

1. Carefully remove the heat press machine and all accessories from the packaging.
2. Place the machine on a stable, flat, and heat-resistant surface. Ensure adequate ventilation around the machine.
3. Keep the machine away from flammable materials and out of reach of children.

5.2 Connexió d'alimentació

1. Assegureu-vos que l'interruptor d'alimentació de la màquina estigui en la posició "OFF".
2. Connect the power cord to the machine's power input.
3. Connecteu l'altre extrem del cable d'alimentació a una presa de corrent amb connexió a terra.

6. Instruccions de funcionament

6.1 Passos bàsics d'operació

Follow these general steps for sublimation transfer:

1. Power On and Set Parameters: Turn on the machine. Use the control panel to set the desired temperature and time according to the material being pressed. Short presses adjust by 5 units, long presses by 10 units.
2. Preheat and Mount Item: Place the appropriate fixture (e.g., phone case fixture) into the machine. Allow the machine to preheat. Once preheated, mount your item (e.g., phone case) onto the fixture.
3. Position Sublimation Film: Place the printed sublimation film onto the item. Ensure the matte side of the film is facing the print side of the item. Secure with heat-resistant tape if necessary.
4. Inicia la transferència: Close the lid and initiate the heat press process. The machine will apply heat and vacuum pressure.
5. Treure la pel·lícula: Once the transfer is complete and the machine signals, carefully open the lid (using heat-resistant gloves). Peel off the sublimation film while the item is still hot for best results.

Image 6.1: Visual guide for the 6-minute heat press process. This image illustrates the four key steps: powering on and setting parameters, preheating and mounting the item, positioning the sublimation film, and peeling the film after transfer.

6.2 Temperature and Time Reference Chart

Refer to the following chart for recommended settings. Adjustments may be necessary based on specific materials and desired results.

Image 6.2: Quick Reference Chart for various substrates. This chart provides recommended upper heat plate temperature, lower heat plate temperature, preheat time, transfer time, and peeling method for phone cases, badges, ceramic plates, coasters, and keychains.

6.3 Using Fixtures and Compatibility

The machine includes adjustable fixtures for various items. The phone case fixture is designed to accommodate most popular phone models.

Image 6.3: The HTVRONT H17 machine with a phone case fixture, demonstrating compatibility with various popular phone models.

For iPhone models, the fixture is compatible with iPhone 12 and above. Android molds are compatible with Samsung, Xiaomi, Google, Huawei, and other brands. The adjustable design minimizes the need for multiple specific molds.

Imatge 6.4: Detallada view of the phone case fixture components, including the main fixture, lens pads, and filler blocks for universal adaptation.

Image 6.5: Model Compatibility Chart. This chart lists various iPhone models and the corresponding lens pad and filler block combinations to use with the phone case fixture.

6.4 Design Software Integration

The HTVRONT H17 supports the use of the IS software, which provides a mobile model library and tools for precise design preparation.

• Adjust pattern size and position within templates.
• Perform mirror processing for sublimation.
• Output sublimation-ready files to ensure accurate pressing without offset or cutting errors.

Image 6.6: Screenshot of the design software interface demonstrating smart alignment features for phone case designs.

7. Manteniment

7.1 Neteja de la màquina

1. Ensure the machine is unplugged and completely cooled down before cleaning.
2. Netegeu les superfícies exteriors amb un damp tela. No utilitzeu netejadors abrasius ni dissolvents.
3. Gently clean the heating plates with a soft, dry cloth. Avoid scratching the surface.
4. Remove any debris or residue from the vacuum area.

7.2 Emmagatzematge

Store the machine in a dry, cool place, away from direct sunlight and moisture. Keep it covered to prevent dust accumulation.

8. Solució De Problemes

9. Especificacions

10. Garantia i Suport

10.1 Informació de la garantia

HTVRONT is committed to providing quality products. For specific warranty details, please refer to the warranty card included with your product or visit the official HTVRONT weblloc web. Conserveu el rebut de compra com a comprovant de compra per a reclamacions de garantia.

10.2 Atenció al client

If you encounter any issues or have questions regarding your HTVRONT H17 Phone Case Heat Press Machine, please contact our customer support team. We offer excellent after-sales service to assist you.

• Guia d'usuari en línia: Podeu descarregar una guia d'usuari detallada en PDF: Descarrega la Guia de l'usuari (PDF)
• Informació de contacte: Please refer to the contact details provided on the HTVRONT official website or your product packaging for the most up-to-date support channels.