TURBRO 72W UV Sanitizer Lamp Manual d'instruccions

Introducció

This manual provides essential information for the safe and effective installation, operation, and maintenance of your TURBRO 72W UV Sanitizer Lamp, Model UV72PA. This device is designed to purify air within HVAC units and ducted systems using ozone-free ultraviolet-C (UV-C) light, featuring an energy-saving airflow sensor for optimized performance.

Informació de seguretat

ADVERTIMENT: Ultraviolet-C (UV-C) light is harmful to eyes and skin. Never look directly at the UV lamp when it is operating. Avoid direct exposure to UV-C light. Always disconnect power before servicing or replacing the lamp.

• Ensure the product is installed by a qualified technician in accordance with local electrical codes.
• No feu funcionar lamp outside of the HVAC duct system.
• This product is ETL listed, ensuring compliance with safety standards. It also meets EPA and CARB ozone limit standards, maintaining ozone levels below 0.05 ppm (equivalent to 0 ozone).
• A slight odor may be noticeable during the first few hours of operation; this is normal and will dissipate.
• Mantingueu els nens i les mascotes allunyats de la zona d'instal·lació.

Contingut del paquet

Verifiqueu que tots els elements que s'enumeren a continuació s'inclouen al vostre paquet:

• 2 x 15.2-inch UV Lamps
• 1 x Ballast
• 4 x Seal Strips
• 4 x cargols de muntatge
• 1 x 2-1/4 inch Drill Bit Set
• 1 x Plantilla d'instal·lació

Figura 1: Contingut del paquet

Especificacions

Figure 2: Power Rating Comparison

Configuració i instal·lació

Follow these steps for proper installation of your UV Sanitizer Lamp:

1. Tria la ubicació: Select a suitable location on the exterior of your HVAC ductwork. Ensure there is at least 16 inches of clear space inside the duct where the UV lamps will be positioned. A nearby 120V electrical outlet is required for power.
2. Prepare Duct: Use the provided installation template to mark the drilling points on the duct exterior.
3. Forats: Using the included 2-1/4 inch drill bit, carefully drill the marked holes through the ductwork.
4. Insereix Lamps: Gently insert the UV lamps through the drilled holes into the duct. Ensure the 2G11 4-pin ceramic base is securely seated.
5. Mount Ballast: Secure the ballast unit to the exterior of the duct using the provided mounting screws. Ensure the ballast is firmly attached.
6. Connectar l'alimentació: Plug the ballast into a standard 120V electrical outlet.

Figure 3: Installation Requirements

Figure 4: Using the Installation Template

Figure 5: 4-Pin 2G11 Lamp Base

Instruccions de funcionament

The TURBRO UV Sanitizer Lamp offers two operating modes:

• Mode HOLD: Provides continuous UV disinfection. The lamp remains on as long as power is supplied.
• AIRFLOW Mode: Activates the UV lamp only when airflow is detected within the HVAC system. This mode conserves energy and extends lamp vida.

To select a mode, refer to the switch on the ballast unit. The green indicator lights on the ballast (labeled "UPPER" and "LOWER") confirm that the system is functioning correctly and the lamps estan actius.

Figure 6: Smart Airflow Sensor Operation

Figure 7: Ballast Status Indicators

Manteniment

Regular maintenance ensures optimal performance and longevity of your UV Sanitizer Lamp.

• Lamp Substitució: UV-C lamps have a finite lifespan. It is recommended to replace the lamps annually to maintain germicidal effectiveness. Refer to the model number on your lamp for compatible replacements.
• Neteja: Inspeccioneu periòdicament la lamps for dust or debris accumulation. If necessary, gently wipe the quartz glass with a clean, dry cloth. Do not use liquid cleaners.
• Precaució de seguretat: Always disconnect power to the unit before performing any maintenance, including lamp substitució o neteja.

Resolució de problemes

If you encounter issues with your UV Sanitizer Lamp, consulteu els problemes i solucions habituals següents:

Garantia i Suport

This TURBRO product is covered by a manufacturer's warranty. For specific warranty terms and conditions, please refer to the documentation included with your purchase or visit the official TURBRO website. For technical support, replacement parts, or any inquiries, please contact TURBRO customer service.

Informació de contacte: Please refer to the TURBRO official weblloc web o el rebut de compra per obtenir les dades de contacte del servei d'atenció al client més actualitzades.