1. Introducció
This manual provides detailed instructions for the safe and effective use of your Godox K-180A 180Ws Photography Studio Flash Strobe Light Kit. Please read this manual thoroughly before operating the equipment and keep it for future reference.
2. Informació de seguretat
Always observe basic safety precautions when using electrical equipment to reduce the risk of fire, electric shock, or injury.
- No exposeu la unitat a la pluja o la humitat.
- Do not disassemble the unit. If repairs are needed, contact qualified service personnel.
- Assegureu-vos que la potència voltage matches the unit's requirements (AC220/60Hz or 110V/60Hz).
- Mantenir fora de l'abast dels nens.
- Unplug the unit from the power source before cleaning or when not in use.
- Avoid prolonged continuous use of the modeling lamp; allow it to cool down for at least 1 minute after 5 minutes of continuous use to prevent overheating.
3. Contingut del paquet
Verify that all items are included in your package (based on Kit 8, the most comprehensive option):
- 1x Godox K-180A Flash Unit
- 1x RT-16 Trigger (Transmitter and Receiver)
- 1x 180cm Light Stand
- 1x FS50X70cm Grid Softbox
- 1x Modeling Lamp
- 1x cable d'alimentació
4. Instruccions de configuració
4.1. Light Stand Assembly
Unfold the light stand legs and extend the telescopic sections to the desired height. Ensure all locking knobs are securely tightened.
4.2. Flash Unit Preparation
- Mount the K-180A flash unit onto the top stud of the light stand.
- Adjust the mounting bracket to achieve the desired angle and securely tighten it.
- The umbrella input is available for attaching a studio umbrella if desired.
4.3. Muntatge de la caixa de llum
Assemble the FS50X70cm Grid Softbox according to its specific instructions. Attach it to the universal mount on the flash unit.
4.4. RT-16 Trigger Setup
Insert the 23A 12V battery into the transmitter and 2 AAA batteries into the receiver (AAA batteries for receiver not included). Connect the receiver to the flash unit's sync port.
4.5. Connexió d'alimentació
Connect the power cord to the flash unit's power socket and then to a suitable AC power outlet. Ensure the power switch is in the OFF position before connecting.
5. Instruccions de funcionament
5.1. Encendre/apagar
Flip the Power Switch (labeled 'POWER') to turn the flash unit ON or OFF. The Charging LED Indicator will illuminate during charging.
5.2. Modelatge Lamp Control
Use the Modeling Light Switch (labeled 'MODEL') to turn the modeling lamp ON or OFF. Pushing it downwards (G position) turns it off, upwards (F position) turns it on. Note: Do not keep the modeling lamp on for too long; it is recommended to cool it down for 1 minute after 5 minutes of continuous use.
5.3. Flash Output Control
Rotate the Flash Output Controller (labeled with '+' and '-') to adjust the flash power. The output is stepless from 1/8 to full power. This allows for precise light requirements in different environments.
5.4. Botó de prova
To test the flash or before taking a picture, push the Test Button (labeled 'TEST'). This can also be used to adjust the brightness when combined with the flash output controller.
5.5. Slave Trigger Mode
The flash unit can be triggered synchronously with one external flash. This mode allows the K-180A to act as an auxiliary lamp, que ofereix diversos efectes de llum i ombra.
6. Manteniment
- Neteja: Use a soft, dry cloth to clean the exterior of the flash unit and accessories. Do not use abrasive cleaners or solvents.
- Emmagatzematge: Store the kit in a cool, dry place, away from direct sunlight and excessive humidity.
- Substitució de fusibles: If the unit fails to power on, check the fuse. Replace it with a fuse of the same rating (5A).
7. Solució De Problemes
- El flaix no s'activa:
- Check if the unit is powered on and connected correctly.
- Ensure the RT-16 trigger transmitter and receiver have fresh batteries and are properly synced.
- Verify the sync cord is securely connected to the flash unit.
- Comproveu el fusible.
- Modelatge lamp no treballant:
- Ensure the Modeling Light Switch is in the ON position.
- Comproveu si la lamp bulb is securely installed and not burnt out.
- Sortida de flaix inconsistent:
- Ensure the Flash Output Controller is set correctly.
- Allow sufficient recharging time between flashes.
8. Especificacions
8.1. Godox K-180A Flash Unit
| Característica | Especificació |
|---|---|
| Model | K-180A |
| Sortida de flaix | 180WS |
| Número de guia (m ISO 100) | 45 |
| Temperatura de color | 5600 ± 200K |
| Potència Voltage | AC220/60Hz or 100V/60Hz (Optional, check your unit) |
| Control de potència del flaix | Stepless (1/8-full) |
| Modelatge Lamp | 75WS |
| Temps de recàrrega | 0.5-3 seg |
| Flash Triggering Model | Sync cord, Test button, Slave |
| Durada del flaix | 1 / 2000-1 / 800 |
| Fusible | 5A |
| Dimensió | 17 x 10 x 17.5cm (approx. 7.2 x 4.1 x 5.4in) |
| Pes | Approx. 0.59KG (approx. 603g / 21.3oz) |
8.2. 180cm Light Stand
| Característica | Especificació |
|---|---|
| Coixinet de càrrega | 2 kg |
| Alçada telescòpica | 82-200 cm |
| Alçada d'emmagatzematge | 68 cm |
| Diàmetre del tub | Φ1.6/1.9/2.2cm |
| Forat de cargol | 1/4" |
| Pes | 0.81 kg |
| Longitud plegada | 67 cm |
| Longitud mínima | 70cm (2'4") |
| Altura màx | 200cm (7') |
| Ideal Max. Working Height | 140-150 cm |
8.3. FS50X70cm Grid Softbox
| Característica | Especificació |
|---|---|
| Mida | 50 x 70cm / 20" x 27" |
| Muntanya | Muntatge Universal |
| Pes | Aprox. 0.6 kg |
8.4. RT-16 Wireless Flash Trigger
| Característica | Especificació |
|---|---|
| Tipus | Activador de flaix sense fil |
| Canals | 16 canals |
| Entrada de potència del transmissor | 23A 12V battery (included) |
| Entrada d'alimentació del receptor | 2 * AAA batteries (not included) |
| Receiver Plug Size | 3.5 mm |
| Adapter Size for Receiver Plug | 3.5 mm i 6.35 mm |
| Radio Working Frequency | 433 MHz |
| Velocitat de sincronització | 1/200 s |
| Outdoor Operation Distance | Fins a 30 m (espai obert) |
| Indoor Operation Distance | Fins a 20 m (espai obert) |
| Mida del paquet | 21.5 x 7.5 x 3.8cm / 8.5 x 3.0 x 1.5 in |
| Pes del paquet | 125 g / 4.4 oz |
9. Consells d'usuari
- Ús de la fotografia: This kit is primarily intended for photography, providing controlled lighting for studio setups. Experiment with different flash power settings and softbox positions to achieve desired lighting effects.
- Modelatge Lamp Ús: While useful for previewing lighting, remember to give the modeling lamp breaks to prevent overheating and prolong its lifespan.
- Trigger Placement: For optimal wireless triggering, ensure a clear line of sight between the RT-16 transmitter and receiver, especially in indoor environments.
10. Garantia i Suport
Per obtenir informació sobre la garantia, assistència tècnica o consultes sobre el servei, poseu-vos en contacte directament amb el venedor o el fabricant. Conserveu el rebut de compra com a comprovant de compra.
