MicroZone RC Receiver Instruction Manual

1. Introducció

This manual provides essential information for the proper setup, operation, and maintenance of your MicroZone RC receivers. Please read this manual thoroughly before using your receiver to ensure safe and optimal performance. These receivers are designed for use with various RC models, including airplanes and drones, and are compatible with specific MicroZone transmitters.

Figure 1: Various MicroZone RC Receiver Models

2. Transmitter & Receiver Compatibility

Ensure your receiver is compatible with your MicroZone transmitter. Refer to the compatibility table below for details.

Figure 2: Comparison Table of Transmitter & Receiver Compatibility

Nota: A checkmark (✓) indicates full compatibility. An orange dot (•) indicates specific or partial compatibility, please consult your transmitter's manual for further details on these pairings.

3. Especificacions

Detailed specifications for each receiver model are provided below.

3.1. MC6RE Mini Receiver

Figure 3: MC6RE Mini Receiver

3.2. MC7RB Receiver

Figure 4: MC7RB Receiver

3.3. MC8RE Receiver

Figure 5: MC8RE Receiver

3.4. MC9002 Receiver PWM/SBUS

Figure 6: MC9002 Receiver

3.5. MC9008S Receiver

Figure 7: MC9008S Receiver

3.6. Mini M-SBUS Receiver (for MC6C)

Figure 8: Mini M-SBUS Receiver

4. Setup and Binding

Before operating your RC model, the receiver must be properly connected and bound to your compatible MicroZone transmitter.

4.1. Connexions

Connect the receiver to your flight controller or servos according to your model's wiring diagram. Ensure correct polarity for power connections. PWM channels are typically connected directly to servos, while SBUS outputs connect to flight controllers that support SBUS input.

Figura 9: Example Receiver Connections (MC-GPS and E7R shown)

4.2. Binding Procedure (Frequency Matching)

The binding process, also referred to as 'contact frequency' or 'electric shock frequency', establishes a secure communication link between your transmitter and receiver. The exact steps may vary slightly by transmitter model, but generally involve:

1. Assegureu-vos que tant l'emissor com el receptor estiguin apagats.
2. Connect a bind plug (if required by your receiver model) to the 'BIND' port on the receiver.
3. Power on the receiver. The LED indicator on the receiver should start flashing, indicating it is in bind mode.
4. While holding the bind button on your transmitter (if applicable), power on the transmitter.
5. Observe the receiver's LED. Once binding is successful, the LED should turn solid or flash in a different pattern (refer to your specific receiver's LED indicator guide).
6. Power off both the receiver and transmitter.
7. Traieu el connector de connexió del receptor.
8. Power on the transmitter first, then the receiver. Verify that the receiver's LED is solid, indicating a successful connection. Test control surfaces or motor response carefully.

For models like the MC9008S, which feature dual antennas, ensure both antennas are positioned optimally for signal reception, typically at 90-degree angles to each other, away from carbon fiber or metal components.

5. Funcionament

Once successfully bound, your receiver will relay control signals from your transmitter to your RC model. Always perform a range check before flying or operating your model to ensure a stable connection.

• Comprovació prèvia al vol: Before each use, verify that all control surfaces respond correctly to transmitter inputs and that the receiver's LED indicates a stable link.
• Signal Loss Protection: Some receivers support 'out of control protection' (failsafe). Configure this feature on your transmitter to ensure your model reacts predictably in case of signal loss (e.g., motors off, control surfaces neutral).
• Voltage Seguiment: Pay attention to the receiver's voltage range. Operating outside this range can lead to performance issues or damage.

6. Manteniment

To ensure the longevity and reliable performance of your MicroZone receiver:

• Keep the receiver clean and free from dust, dirt, and moisture.
• Avoid exposing the receiver to extreme temperatures or direct sunlight for prolonged periods.
• Regularly inspect antenna wires for any damage or kinks. Ensure they are securely attached.
• Store the receiver in a dry, cool place when not in use.

7. Solució De Problemes

If you encounter issues with your MicroZone receiver, consider the following common troubleshooting steps:

• Sense enllaç/error d'enllaç:
• Ensure both transmitter and receiver are fully charged.
• Verify the binding procedure is followed correctly (refer to Section 4.2).
• Comproveu si hi ha interferències d'altres dispositius de 2.4 GHz.
• Confirm receiver compatibility with your transmitter (refer to Section 2).
• Intermittent Signal/Short Range:
• Inspect antenna placement and condition. Ensure antennas are not obstructed by carbon fiber or metal.
• Comproveu si hi ha connexions soltes o cablejat danyat.
• Ensure the receiver is not too close to high-current components (ESCs, motors) that can generate electrical noise.
• Resposta de control incorrecta:
• Verify correct channel mapping on your transmitter and flight controller.
• Ensure servos are connected to the correct PWM ports.

If problems persist, consult your transmitter's manual or seek assistance from experienced RC enthusiasts or the seller.

8. Consells d'usuari

• For optimal signal reception, especially with dual-antenna receivers like the MC9008S, position the antennas at a 90-degree angle to each other. This helps minimize signal loss due to orientation.
• Always perform a thorough range check before the first flight of a new setup or after any significant changes to your RC model.
• Consider using a voltage alarm if your model does not have built-in telemetry to monitor receiver voltage and prevent unexpected power loss.

9. Garantia i Suport

For warranty information, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your purchase records for any warranty claims.