Introducció
Thank you for choosing the JONSBO TG-360 ARGB CPU Liquid Cooler. This all-in-one (AIO) liquid cooling system is designed to provide efficient heat dissipation for your CPU while offering customizable ARGB lighting effects. This manual will guide you through the installation, operation, maintenance, and troubleshooting of your new cooler.
Figure 1: JONSBO TG-360 CPU Liquid Cooler Overview
Configuració i instal·lació
Before installation, ensure your system is powered off and unplugged. Refer to your motherboard manual for specific CPU socket mounting instructions if needed.
Contingut del paquet
Figura 2: Maquinari de muntatge inclòs
Sòcols de CPU compatibles
The JONSBO TG-360 supports a wide range of Intel and AMD sockets:
- **Intel:** LGA 1150, LGA 1155, LGA 1151, LGA1200, LGA 1700, LGA 2011
- **AMD:** AM4, Socket AM5
Figure 3: CPU Socket Compatibility
Passos d'instal·lació (generals)
- Prepareu la CPU i la placa base: Clean the CPU surface thoroughly. Apply thermal paste (included) to the center of the CPU in a pea-sized dot or thin line. The cooler features a slightly convex copper bottom for optimal contact.
- Instal·leu els suports de muntatge: Attach the appropriate mounting brackets for your CPU socket to the pump head.
- Muntar el radiador i els ventiladors: Secure the radiator to an available mounting location in your PC case (e.g., top, front, or rear). Ensure fans are oriented for optimal airflow (typically exhausting air out of the case when mounted at the top/rear, or intaking air when mounted at the front).
- Instal·leu el capçal de la bomba: Carefully place the pump head onto the CPU, aligning it with the mounting holes. Secure it with the provided screws, tightening them in a cross pattern until snug.
- Connectar els cables:
- Connexió del ventilador: The cold exhaust fan connects to the motherboard with a single cable for simplified wire management. Connect the 4-pin PWM fan connector to an available CPU_FAN or SYS_FAN header on your motherboard.
- Connexió de la bomba: Connect the pump's 3-pin power connector to a dedicated AIO_PUMP or PUMP_FAN header on your motherboard.
- Il·luminació ARGB: Connect the 5V 3-pin ARGB connector from the cooler to a compatible 5V 3-pin ARGB header on your motherboard. This allows for synchronized lighting effects. Do NOT connect to a 12V RGB header.
- Adjust Pump Logo: The pump head features a damping rotation nameplate, allowing you to adjust the JONSBO logo direction for optimal aesthetic alignment after installation.
Figure 4: ARGB Connection Diagram
Figure 5: Rotatable Pump Logo
Figure 6: Simplified Fan Wiring
Instruccions de funcionament
Encès
Once installation is complete, power on your computer. The fans and pump should start operating, and the ARGB lighting will illuminate.
Control d'il·luminació ARGB
The JONSBO TG-360 features ARGB Phantom Synchronous Light Effect. This means the customizable lighting can be synchronized with your motherboard's ARGB software (e.g., ASUS Aura Sync, MSI Mystic Light Sync, GIGABYTE RGB Fusion, ASRock Polychrome Sync). Ensure the 5V 3-pin ARGB cable is correctly connected to your motherboard's ARGB header.
Figure 7: Motherboard ARGB Software Interface Example
Control de velocitat del ventilador
The fans are PWM controlled, allowing your motherboard to dynamically adjust their speed based on CPU temperature. This ensures optimal cooling performance and reduced noise levels when the system is under light load.
Video 1: JONSBO TG-240/360 ARGB Water/Liquid Cooler in action, showcasing RGB lighting and features.
Manteniment
Un manteniment regular ajuda a garantir la longevitat i el rendiment òptim del vostre refrigerador de líquid.
- Neteja de pols: Netegeu periòdicament les aletes del radiador i les aspes del ventilador per evitar l'acumulació de pols, que pot impedir el flux d'aire i reduir l'eficiència de la refrigeració. Feu servir aire comprimit o un raspall suau.
- Comprovació de la canonada i les connexions: While the cooler features a compression multilayer sealing interface for strong sealing and no leakage, it's good practice to occasionally inspect the tubing and connections for any signs of wear or damage.
- Vida útil del ventilador: The fans are designed for a long lifespan of ≥40,000 hours at 25°C.
Resolució de problemes
Sense alimentació/Els ventiladors no giren
- Ensure all power cables (4-pin PWM for fans, 3-pin for pump) are securely connected to the correct headers on your motherboard.
- Check your motherboard's BIOS/UEFI settings to ensure fan headers are enabled and configured correctly.
ARGB Lighting Not Working/Synchronizing
- Verify that the 5V 3-pin ARGB connector is securely plugged into a compatible 5V 3-pin ARGB header on your motherboard.
- Do NOT connect to a 12V RGB header, as this can damage the LEDs.
- Ensure your motherboard's ARGB software is installed and updated, and that the lighting effects are enabled and configured.
- If using a separate ARGB controller, ensure it is powered and correctly connected.
Rendiment de refrigeració deficient
- Check if the pump is running (you might hear a faint hum or feel vibrations). If not, refer to 'No Power/Fans Not Spinning'.
- Ensure the pump head is making good contact with the CPU. Re-seat if necessary, reapplying thermal paste.
- Verify that the fans are spinning and oriented correctly for optimal airflow.
- Clean any dust buildup from the radiator fins and fan blades.
- Check CPU temperatures using monitoring software to confirm the issue.
Especificacions
Figura 8: Paràmetres detallats del producte
| Característica | Especificació |
|---|---|
| Número de model | TG-360 |
| Tipus | CPU All In One Liquid Cooler |
| Mida del radiador | 397 mm (L) x 120 mm (A) x 27 mm (Al) |
| Mida del ventilador | 120mm x 120mm x 25mm (each) |
| Velocitat del ventilador | 900-1800 RPM (±10%) |
| Volum d'aire | 29.22-66.19 CFM (each) |
| Soroll del ventilador | 22.9-35.4 dB(A) (max) |
| Coixinet del ventilador | Hidràulica |
| Interfície de ventilador | PWM 4-pin |
| Mida de la bomba | 74 mm x 89.2 mm x 51.8 mm |
| Velocitat de la bomba | 2500 RPM (±10%) |
| Soroll de la bomba | < 30 dB(A) |
| Bomba Voltage | 12V DC |
| Potència de la bomba | 3.6W |
| Suport RGB | A-RGB (5V 3-pin) |
| Material del dissipador de calor | Copper & Aluminum |
| CPU compatible | LGA 1150, LGA 1155, LGA 1151, LGA1200, AM4, LGA 1700, Socket AM5, LGA 2011 |
| Certificació | CE, RoHS |
Consells per a l'usuari
- Gestió de cables: Avançanttage of the simplified fan wiring (single cable per fan) to achieve a cleaner build. Plan your cable routes before securing components.
- ARGB Customization: Experiment with your motherboard's ARGB software to find your preferred lighting patterns and colors. The 5V 3-pin ARGB allows for addressable effects.
- Orientació de la bomba: The rotatable pump logo is a thoughtful design feature. Don't forget to adjust it to match your build's aesthetic after the pump is mounted.
- Aplicació de pasta tèrmica: While the cooler comes with thermal paste, ensure it's applied evenly and adequately for the best heat transfer.
Garantia i Suport
For warranty claims or technical support, please contact your retailer or the official JONSBO customer service. Keep your proof of purchase for any warranty-related inquiries.
