Surpass Hobby M Series Waterproof ESC Instruction Manual

1. Introducció

This manual provides detailed instructions for the installation, operation, and maintenance of your Surpass Hobby M Series Waterproof Electronic Speed Controller (ESC). The M Series ESCs (35A, 45A, 60A) are designed for 1/10, 1/12, 1/14, and 1/16 scale RC cars, offering robust performance with sensorless brushless motors.

2. Característiques clau

• Impermeable i a prova de pols: Designed for all-weather racing conditions. (Note: Remove cooling fan before water use; clean and dry thoroughly afterward to prevent connector rust.)
• Optimized for RC Cars: Excellent start-up, acceleration, and linearity characteristics.
• Sensorless Brushless Motor Compatibility: Seamless integration with sensorless brushless motors.
• High Current Resistance & Heat Dissipation: Robust design for demanding applications.
• Múltiples funcions de protecció:
  • Vol baixtage cut-off protection for Lithium (LiPo) or Nickel (NiMH) batteries.
  • Throttle signal loss protection.
  • Motor blocked protection.
• Volum baixtage Cut-off Indication: Motor emits "Beep-Beep" sound and LED flashes.
• Built-in BEC:
  • M35A: Analog-mode BEC 5V/2A.
  • M45A/M60A: Switch-mode BEC 5.3V/2A for high torque and high voltagi servos.
• Programable: Easily configured using a pocket-sized program card.

3. Especificacions

Refer to the table below for detailed specifications of the M Series ESCs:

4. Contingut del paquet

El vostre paquet hauria d'incloure els elements següents:

• Surpass Hobby M Series Waterproof ESC (35A, 45A, or 60A model as selected)
• Optional: Programming Card (may be sold separately or included depending on package)

5. Instal·lació i configuració

Follow these steps to properly install your ESC in your RC vehicle:

1. Muntatge de l'ESC: Securely mount the ESC in your RC car chassis using double-sided tape or screws, ensuring good airflow for cooling.
2. Connexió del motor: Connect the three motor wires from the ESC to your brushless motor. The order of connection may affect motor rotation direction; if the motor spins in the wrong direction, swap any two of the three wires.
3. Connexió de la bateria: Connect your battery pack to the ESC's power input wires. Ensure correct polarity (red to positive, black to negative). The ESC supports T-Plug or XT60 Plug connectors depending on the variant.
4. Connexió del receptor: Plug the ESC's 3-pin servo connector (usually black, red, white/orange wires) into the throttle channel (typically channel 2) of your RC receiver.
5. Interruptor d'alimentació: Ensure the ESC's power switch is accessible for easy on/off control.

Important Note for Water Use:

• Before using the ESC in water, please uninstall the cooling fan.
• After use in water, clean and dry the ESC thoroughly to prevent the connectors from rusting.

6. Funcionament

Once the ESC is correctly installed and connected:

1. Turn on your RC transmitter first.
2. Then, turn on the ESC using its power switch.
3. The ESC will perform a self-test and emit a series of beeps.
4. Calibrate the throttle range if necessary (refer to your transmitter's manual for throttle calibration procedures).
5. You are now ready to operate your RC vehicle.
6. To power off, turn off the ESC first, then your transmitter.

7. Programming Card Usage

The optional programming card allows you to adjust various parameters of your ESC. Connect the programming card to the ESC's programming port (usually the receiver cable port, or a dedicated port if available) before powering on the ESC.

Available settings on the programming card include:

• Volum baixtage Tall: Estableix el voltage at which the ESC will reduce power to protect your battery. Options typically include 3.1V, 2.9V, 2.7V, or 0V (no cut-off, not recommended for LiPo).
• Modes d'inici: Adjust the initial acceleration response. Options like Medium, Soft, or Strong.
• Màx. Força de frenada: Configure the maximum braking power. Options may include 50%, 75%, 100% (for 25A/35A/45A/60A/120A).
• Màx. Força inversa: Set the maximum power for reverse movement. Options may include 25%, 50%, 75%, 100%.
• Interval neutre: Define the dead band around the neutral throttle position. Options like 9%, 6%, 12%, or Work State.

Use the buttons on the programming card to navigate and select your desired settings. Press 'Programme' to save changes and 'Reset' to restore factory defaults.

8. Manteniment

• Regularly inspect all wires and connectors for damage or loose connections.
• Keep the ESC clean and free from dirt, dust, and debris.
• If used in wet conditions, ensure the ESC is thoroughly dried and cleaned immediately after use to prevent corrosion, especially on connectors.
• Ensure the cooling fan (if installed) is free from obstructions and functioning correctly.

9. Solució De Problemes

10. Consells d'usuari

• Funcionalitat inversa: The ESC does support reverse, which can be adjusted via the programming card's 'Max. reverse force' setting.
• Compatibilitat de la bateria: The 60A ESC model supports 2S (7.4V) and 3S (11.1V) LiPo batteries, as well as 4-9 cell NiMH batteries, as detailed in the specifications. Always ensure your battery voltage matches the ESC's capabilities.
• Motor Connector Size: While not explicitly stated, the motor connectors are typically standard bullet connectors (e.g., 3.5mm or 4mm) compatible with most brushless RC motors. Ensure a snug fit for optimal performance.

11. Garantia i Suport

For warranty information, technical support, or any issues not covered in this manual, please contact the seller or manufacturer directly. Keep your proof of purchase for any warranty claims.